Page 1174 of 1501
![MITSUBISHI MONTERO 1998 Service Manual \
\
\
\
\
\
\
AIR RIDE SUSPENSION - WARNING LAMPS
AIR RIDE SU](/manual-img/19/57333/w960_57333-1173.png "MITSUBISHI MONTERO 1998 Service Manual \
\
\
\
\
\
\
AIR RIDE SUSPENSION - WARNING LAMPS
AIR RIDE SU")
\
\
\
\
\
\
\
AIR RIDE SUSPENSION - WARNING LAMPS
AIR RIDE SUSPENSION - WARNING LAMP INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bulb burned out ......... A ............ Require replacement.
Warning light does
not come on during
bulb check ............. .. . Further inspection required to
determine cause.
Warning light flashes ... .. . Further inspection required to
determine cause.
Warning light is
intermittent ........... .. . Further inspection required to
determine cause.
Warning light stays
on after initial
bulb check ............. .. . Further inspection required to
determine cause.
\
\
\
\
\
\
\
AIR RIDE SUSPENSION - WIRING HARNESSES
AIR RIDE SUSPENSION - WIRING HARNESS INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Connector bent .......... A .. Require repair or replacement.
Connector broken ........ A .. Require repair or replacement.
Connector loose ......... A .. Require repair or replacement.
Damaged (cut, burned, or
chafed) ................ A .. Require repair or replacement.
Excessive resistance .... B .. Require repair or replacement.
Fuse blown .............. A ............ Require replacement.
Fusible link blown ...... A ............ Require replacement.
Open .................... A .. Require repair or replacement.
Poor ground ............. A .. Require repair or replacement.
Routed incorrectly ...... B .. Require rerouting according to
vehicle manufacturer's
specifications.
Shorted ................. A .. Require repair or replacement.
Terminal bent ........... A .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal corroded ....... A .. Require repair or replacement.
Terminal loose .......... A .. Require repair or replacement.
\
\
\
\
\
\
\
BALL JOINTS
Before requiring or suggesting ball joint replacement, the
approved OEM procedure must be used to measure ball joint wear. The
measurement(s) obtained, along with the vehicle manufacturer's
specifications, must be noted on the inspection report. Some states
require that these measurements also appear on the invoice.
NOTE: The term "perceptible movement," defined as any visible
movement in any direction, has been the industry standard
for determining the need for replacement of follower ball
joints. Some vehicle manufacturers are now publishing
specifications for follower ball joints that were
Page 1218 of 1501
COMPONENT TESTS
DRIVE MOTOR
Eclipse & Montero Sport
Remove drive motor. See DRIVE MOTOR R & I under REMOVAL &
INSTALLATION. Using 12-volt power supply, apply voltage to 2-terminal
connector. Reverse power supply leads to reverse motor direction.
Replace motor as necessary.
Galant
Remove drive motor. See DRIVE MOTOR R & I under REMOVAL &
INSTALLATION. Using 12-volt power supply, apply voltage to terminals
No. 1 (Blue wire) and No. 4 (Blue/White wire) of 6-terminal drive
motor connector. Reverse power supply leads to reverse motor
direction. Replace motor as necessary.
Montero
Remove drive motor. See DRIVE MOTOR R & I under REMOVAL &
INSTALLATION. Using 12-volt power supply, apply voltage to terminals
No. 1 (Green wire) and No. 3 (Green/Red wire and Black wire) of 4-
terminal drive motor connector. Reverse power supply leads to reverse
motor direction. Replace motor as necessary.
3000GT
Remove drive motor. See DRIVE MOTOR R & I under REMOVAL &
INSTALLATION. Using 12-volt power supply, apply voltage to terminals
No. 1 (Red/Blue wire) and No. 2 (Red/Yellow wire) of 8-terminal driv\
e
motor connector. Reverse power supply leads to reverse motor
direction. Replace motor as necessary.
DRIVE MOTOR LIMIT SWITCH
Eclipse & Montero Sport
1) Remove sun roof ECU. Look into viewing windows while
turning rotating wheel. See Fig. 2. Turn rotating wheel until White
marks appear. When White marks appear in viewing windows at same time,
stop turning rotating wheel.
2) Close sun roof fully. Install timed sun roof control unit.
Ensure wiring connector is properly inserted into control unit. Insert
a flat-blade screwdriver, place on tab and press to right, being
careful not to pinch wiring. See Fig. 3.
Fig. 2: Timing Sun Roof ECU (Eclipse & Montero Sport)
Courtesy of Mitsubishi Motor Sales of America
Page 1228 of 1501
SUN ROOF R & I
Removal & Installation (Eclipse & Galant)
1) Remove side trim covers by lightly pulling panels straight
down. Unbolt and remove roof glass panel with adjust plates. See
Fig. 1 . Operate sun roof drive cable assembly to fully open position.
Remove deflector. Remove guide rail cover. Operate sun roof drive
cable assembly to fully closed position and remove rear drip channel.
2) Remove overhead switch assembly. Remove rear seat. Push
down on rear seat cushion and pull seat release lever. Unbolt and
remove seat back. Remove front and rear door scuff plate.
3) Remove center pillar lower and upper trim. Remove roof
rail and sun roof trim strips. Remove front and rear pillar trim.
Remove assist handle. Remove headliner. Disconnect motor harness
connector. Remove motor mounting bolts and remove motor.
4) Attach protective tape around roof opening. Pull sliding
roof assembly forward through roof opening. Disconnect drain hoses. If
drain hoses need replacement, attach cord to exterior end of drain
hose. Pull drain hose from interior end. Remove housing assembly and
set brackets.
5) To install components, reverse removal procedure. Sun roof
drive cables must be properly indexed to drive motor drive gear.
Remove drive motor cam gear cover. Using manual closure wrench
(included in tool pouch), rotate motor to correct position. See
Fig. 12 . Install motor. Install remaining components. To adjust roof
glass panel, see SUN ROOF GLASS FIT under ADJUSTMENTS.
Removal & Installation (Montero)
1) Remove trim covers. Unbolt roof glass panel from sliding
assembly and remove. Remove sun roof switch assembly and drive motor.
Remove front and rear door scuff plate.
2) Remove center pillar lower and upper trim. Remove roof
rail and sun roof trim strips. Remove front and rear pillar trim.
Remove assist handle. Remove headliner. Remove rear set bracket.
Remove sun roof assembly. Disconnect drain hoses.
3) If drain hoses need replacement, attach cord to exterior
end of drain hose. Pull drain hose from interior end. To install
components, reverse removal procedure. See DRIVE MOTOR R & I for
installation procedures.
Removal & Installation (Montero Sport & 3000GT)
Remove sun roof switch and dome light assembly. Remove
bracket behind dome light. Remove headliner. Remove drain hose
retaining clips and remove drain hose. Remove sun roof assembly. To
install, reverse removal procedure.
WIRING DIAGRAMS
Page 1229 of 1501
Fig. 14: Power Sun Roof System Wiring Diagram (Eclipse)
Page 1230 of 1501
Fig. 15: Power Sun Roof System Wiring Diagram (Galant)
Page 1231 of 1501
Fig. 16: Power Sun Roof System Wiring Diagram (Montero)
Page 1232 of 1501
Fig. 17: Power Sun Roof System Wiring Diagram (Montero Sport)
Page 1233 of 1501
Fig. 18: Power Sun Roof System Wiring Diagram (3000GT)
