1998 MITSUBISHI MONTERO radiator
[x] Cancel search: radiatorPage 999 of 1501
2) Disconnect air intake hose and vacuum hoses. Remove air
hose and air outlet housing. Remove heat protectors. Disconnect
exhaust pipe. Remove power steering oil pump and bracket. Remove
engine hanger bracket. Disconnect oil inlet pipe.
3) Disconnect engine coolant hoses and tubes from
turbocharger. Remove exhaust manifold nuts and bolts. Remove exhaust
manifold and gaskets. Disconnect oil pressure and return pipes. Remove
turbocharger and exhaust manifold assembly. Separate turbocharger from
exhaust manifold.
Removal (3000GT - Front)
1) Disconnect negative battery cable. Drain engine oil and
coolant. Remove radiator. Disconnect exhaust pipe. Remove air intake
hose, air hoses and air pipe. Remove generator and belt. Remove oil
dipstick guide.
2) Remove heat protector. Disconnect front heated oxygen
sensor connector. Remove oil return pipe. Remove turbocharger support
bracket, and remove turbocharger from exhaust manifold.
Removal (3000GT - Rear)
1) Disconnect battery cables, and remove battery. Drain
engine oil and cooling system. Remove accelerator cable. Remove air
hose, air pipe and heat protectors. Disconnect clutch booster vacuum
hose. Remove air intake hoses and EGR pipe. Disconnect heated oxygen
sensor connectors.
2) Remove oil pipe and EGR valve. Disconnect exhaust fitting,
and remove rear heat protector. Remove oil return pipe. Remove
turbocharger assembly.
Inspection (All Models)
Check turbine and compressor wheels for cracking and other
damage. Ensure turbine and compressor wheels turn smoothly. Check for
oil leakage from turbocharger assembly. Check for proper wastegate
valve operation. See I - SYSTEM/COMPONENT TESTS article.
CAUTION: Apply light coat of oil to inner surface of flared area on
water pipe (flare nut fitting) before connecting to engine.
Installation (All Models)
1) To install, reverse removal procedure. Before oil pipe
flare nut (above turbocharger) is installed, pour clean engine oil
into turbocharger oil pipe installation hole. Ensure oil and air hoses
are properly installed and securely clamped.
2) Use NEW gaskets. Adjust accelerator cable (if necessary).\
Refill engine oil and coolant. Check for oil and coolant leaks.
Tighten all bolts to specification. See TORQUE SPECIFICATIONS.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE\
\
\
\
\
\
Applications Ft. Lbs. (N.m)
Coolant Pipe-To-Turbocharger Banjo Bolt .......... 31 (42)
EGR Valve ........................................ 16 (22)
Engine Coolant Temperature Sensor ................ 22 (30)
Exhaust Manifold-To-Engine Nuts ............ 18-21 (24-29)
Exhaust Manifold-To-Turbocharger Bolts ..... 40-47 (54-64)
Exhaust Pipe Bolts ......................... 21-36 (29-49)
Fuel Filter Line ................................. 27 (36)
Fuel Tank Drain Plug ....................... 11-18 (15-24)
Fuel Tank Nuts ............................. 15-21 (20-29)
Page 1378 of 1501
Parking Brake cables frozen See DRUM BRAKES
BRAKE SYSTEM
Incorrect installation of
inboard disc pad Remove and replace
correctly
Power booster output
rod too long See POWER BRAKE UNITS
BRAKE SYSTEM
Brake pedal not returning See DISC, DRUM BRAKES
freely BRAKE SYSTEM
\
\
\
\
\
\
\
Brakes Grab or
Uneven Braking
Action Malfunction of combination See CONTROL VALVE or
valve BRAKE SYSTEM
Malfunction of power brake See POWER BRAKE UNITS
unit or BRAKE SYSTEM
Binding brake pedal See DISC, DRUM BRAKES
or BRAKE SYSTEM
\
\
\
\
\
\
\
Pulsation or
Roughness Uneven pad wear caused by See DISC BRAKES or
caliper BRAKE SYSTEM
Uneven rotor wear See DISC BRAKES or
BRAKE SYSTEM
Drums out-of-round Reface or replace drums
\
\
\
\
\
\
\
ENGINE MECHANICAL
COOLING SYSTEM TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
COOLING SYSTEM TROUBLE SHOOTING
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Overheating Coolant Leak Fill/Pressure Test
System
A/C Condenser Fins Clogged Remove/Clean Condenser
Radiator Fins Clogged Remove/Clean Radiator
Thermostat Stuck Closed Replace Thermostat
Clogged Cooling System
Passages Clean/Flush Cooling
System
Page 1379 of 1501
Water Pump Malfunction Replace Water Pump
Fan Clutch Malfunction Replace Fan Clutch
Retarded Ignition Timing Reset Ignition Timing
Cooling Fan Malfunction Test Cooling Fan/
Circuit
Cooling Fan Motor
Malfunction Test Fan Motor
Cooling Fan Relay
Malfunction Test Fan Relay
Faulty Radiator Cap Replace Radiator Cap
Broken/Slipping Fan Belt Replace Fan Belt
Restricted Exhaust Repair Exhaust System
\
\
\
\
\
\
\
Corrosion Impurities In Coolant Clean/Flush System \
\
\
\
\
\
\
Coolant Leakage Damaged hose Replace Hose
Leaky Water Pump Replace Water Pump
Damaged Radiator Seam Replace/Repair Radiator
Leaky Thermostat Cover Replace Thermostat
Cover
Cylinder Head Problem Check Head/Head Gasket
Leaky Freeze Plugs Replace Freeze Plugs
\
\
\
\
\
\
\
Recovery System Inoperative
Loose and/or Defective
Radiator Cap Replace Radiator Cap
Overflow Tube Clogged
and/or Leaking Repair Tube
Recovery Bottle Vent
Restricted Clean Vent
\
\
\
\
\
\
\
No Heater Core Flow
Collapsed Heater Hose Replace Heater Hose
Plugged Heater Core Clean/Replace Heater
Core
Faulty Heater Valve Replace Heater Valve
\
\
\
\
\
\
\
GASOLINE ENGINE - MECHANICAL TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available