1998 MITSUBISHI MONTERO fuel pressure
[x] Cancel search: fuel pressurePage 673 of 1501
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
(1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Determine source of contamination, such as engine coolant,
fuel, metal particles, or water. Require repair or
replacement.
( 3) - Inoperative includes intermittent operation or out of
OEM specification. Some components may be serviceable;
check for accepted cleaning procedure.
\
\
\
\
\
\
\
SENSORS AND ACTUATORS
NOTE: Conditions pertaining to the sensors and actuators listed
in this section may be found under the name of the sensor
or actuator.
SENSOR ABBREVIATION TABLE
\
\
\
\
\
\
\
Sensor Abbreviation
Accelerator Pedal Position Sensor ......................... APP
Air Conditioning Cycling Switch ............................ AC
Air Conditioning Pressure Sensor ........................... ..
Air Fuel Ratio Sensor ...................................... ..
Barometric Pressure Sensor ............................... BARO
Camshaft Position Sensor .................................. CMP
Clutch Pedal Position Switch .............................. CPP
Cooling Fan Motor Sensors and Switches ..................... ..
Crankshaft Position Sensor ................................ CKP
Electronic Transmission Feedback Devices ................... ..
Engine Coolant Temperature Sensor ......................... ECT
Evaporative Emission feedback devices ...................... ..
Exhaust Gas Recirculation feedback devices ................. ..
Fan Control Sensor ......................................... FC
Intake Air Temperature Sensor ............................. IAT
Knock Sensor ............................................... KS
Manifold Absolute Pressure Sensor ......................... MAP
Mass Air Flow Sensor ...................................... MAF
O2 Sensor ................................................. O2S
Park Neutral Position Switch .............................. PNP
Power Steering Pressure Sensor ............................ PSP
Thermal Vacuum Valve ...................................... TVV
Throttle Position Sensor ............................ TP Sensor
Throttle Position Switch ................................... ..
Transmission Range Switch ........................... TR Switch
Vehicle Speed Sensor ...................................... VSS
Volume Air Flow Sensor .................................... VAF
\
\
\
\
\
\
\
ACTUATOR ABBREVIATION TABLE \
\
\
\
\
\
\
Actuator Abbreviation
Air Injection Control Solenoid ............................. ..
Electronic Transmission control devices .................... ..
Evaporative Emission Canister ............................ EVAP
Purge Device ............................................... ..
Exhaust Gas Recirculation Device .......................... EGR
Fuel Injector .............................................. ..
Idle Air Control .......................................... IAC
Page 685 of 1501
![MITSUBISHI MONTERO 1998 Service Manual check for accepted cleaning procedure. \
\
\
\
\
\
\
TUB](/manual-img/19/57333/w960_57333-684.png "MITSUBISHI MONTERO 1998 Service Manual check for accepted cleaning procedure. \
\
\
\
\
\
\
TUB")
check for accepted cleaning procedure. \
\
\
\
\
\
\
TUBE CLAMPS
See HOSE AND TUBE COUPLERS, CONNECTORS AND CLAMPS .
TUBE CONNECTORS
See HOSE AND TUBE COUPLERS, CONNECTORS AND CLAMPS .
TUBE COUPLERS
See HOSE AND TUBE COUPLERS, CONNECTORS AND CLAMPS .
TUBES
See HOSES AND TUBES (FUEL LINES , RADIATOR, BY PASS, HEATER,
RECOVERY TANK AND OIL COOLERS).
TURBO CHARGERS
TURBO CHARGER INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Boost pressure
incorrect .............. A ........... ( 1) Require repair or
replacement.
Leaking ................. A .. Require repair or replacement.
Noisy ................... 2 .. Suggest repair or replacement.
Oil seal (internal)
leaking ................ A .. Require repair or replacement.
Vibrates ................ A .. Require repair or replacement.
( 1) - Boost pressure problems may be caused by other systems
or components.
\
\
\
\
\
\
\
VACUUM CONNECTIONS
See VACUUM HOSES, TUBES AND CONNECTIONS (NON-METALLIC) .
VACUUM HOSES, TUBES AND CONNECTIONS (NON-METALLIC)
VACUUM HOSE, TUBE AND CONNECTION (NON-METALLIC) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Leaking ................. A .. Require repair or replacement.
Melted .................. A ............ Require replacement.
Missing ................. C ............ Require replacement.
Oil-soaked (spongy) ..... 1 ............ Suggest replacement.
Page 690 of 1501
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Wire lead conductors
exposed ................ B .. Require repair or replacement.
Wire lead corroded ...... A .. Require repair or replacement.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
(1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Determine source of contamination, such as engine coolant,
fuel, metal particles, or water. Require repair or
replacement.
( 3) - Inoperative includes intermittent operation or out of
OEM specification. Some components may be serviceable;
check for accepted cleaning procedure.
\
\
\
\
\
\
\
WASTE GATES AND BOOST CONTROL MECHANISMS
WASTE GATE AND BOOST CONTROL MECHANISM INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Boost pressure
incorrect .............. A ........... ( 1) Require repair or
replacement. Further
inspection required.
Leaking ................. A .. Require repair or replacement.
( 1) - Incorrect boost pressure includes intermittent operation
or out of OEM specification.
\
\
\
\
\
\
\
WATER PUMPS (ELECTRIC)
WATER PUMP (ELECTRIC) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........... ( 1) Require repair or
replacement.
Connector missing ....... C ............ Require replacement.
Inoperative ............. A ........ ( 2) Require replacement.
Leaking ................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Noisy ................... 2 ............ Suggest replacement.
Rotation incorrect for
application ............ B .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Page 703 of 1501
2.0L
(VIN F) ........................................ 8.5:1
(VIN Y) ........................................ 9.6:1
2.4L (VIN G) ..................................... 9.5:1
3.0L
(VIN H) ........................................ 8.9:1
(VIN J) ....................................... 10.0:1
(VIN K) ........................................ 8.0:1
(VIN P) ........................................ 9.0:1
3.5L (VIN M & P) ................................. 9.0:1
Compression Pressure
1.5L (VIN A) ..................... 192 psi (13.4 kg/cm
)
1.8L (VIN C) ..................... 199 psi (13.9 kg/cm)
2.0L (VIN F) ..................... 178 psi (12.5 kg/cm)
2.0L (VIN Y) ............ 170-225 psi (11.7-15.5 kg/cm)
2.4L (VIN G) ..................... 192 psi (13.4 kg/cm)
3.0L
(VIN H & P) .................... 171 psi (12.0 kg/cm
)
(VIN J) ........................ 185 psi (13.0 kg/cm)
(VIN K) ........................ 156 psi (10.9 kg/cm)
3.5L (VIN M & P) ................. 171 psi (12.0 kg/cm)
Maximum Variation
Between Cylinders ( 2) ............... 14 psi (1.0 kg/cm
)
( 1) - See A - ENGINE/VIN ID article for VIN information.
( 2) - On Eclipse 2.0L non-turbo engine, maximum variation
between cylinders is 25%.
\
\
\
\
\
\
Exhaust System Backpressure
The exhaust system can be tested with a vacuum or pressure
gauge. If using a pressure gauge, remove HO2S or air injection check
valve (if equipped). Connect a 0-5 psi pressure gauge and run engine
at 2500 RPM. If exhaust system backpressure is greater than 2 psi,
exhaust system or catalytic converter is plugged.
If using a vacuum gauge, connect vacuum gauge hose to intake
manifold vacuum port. Start engine. Observe vacuum gauge. Open
throttle part way and hold steady. If vacuum gauge indication slowly
drops after stabilizing, inspect exhaust system for restriction.
FUEL SYSTEM
* PLEASE READ THIS FIRST *
WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel
injection-related component. DO NOT allow fuel to contact
engine or electrical components.
RELIEVING FUEL PRESSURE
1) On Diamante, disconnect fuel pump harness connector at
fuel tank from underneath vehicle. On Montero and Montero Sport,
remove cargo compartment carpet, remove access plate and disconnect
fuel pump harness connector. On all other models, remove rear seat
cushion, remove access plate (if required) and disconnect fuel pump
harness connector.
2) On all models, start engine. Let engine run until it
stops. Turn ignition off. Disconnect negative battery cable. Connect
fuel pump harness connector. Install rear seat and/or carpet as
necessary.
WARNING: Before disconnecting high pressure fuel hose at fuel
Page 704 of 1501
delivery pipe, cover fuel hose connection with a rag. Some
residual fuel pressure may still be in system.
FUEL PRESSURE
1) Relieve fuel pressure. See RELIEVING FUEL PRESSURE. On
models with fuel rail service valve, connect fuel pressure gauge to
fuel rail. On models without fuel rail service valve, disconnect high
pressure fuel inlet line at fuel rail. Remove throttle body bracket
(if necessary). Connect fuel pressure gauge with adapter between fuel
rail and high pressure fuel inlet line. See Fig. 1.
Fig. 1: Installing Fuel Pressure Tester (Typical)
Courtesy of Mitsubishi Motor Sales of America
2) On Eclipse 2.0L non-turbo and Montero Sport, use scan tool
to operate fuel pump. On all other models, operate fuel pump by
connecting battery voltage to fuel pump test terminal. See
FUEL PUMP TEST TERMINAL LOCATION table. Ensure no fuel leaks are
present. Disconnect battery voltage from fuel pump test terminal.
FUEL PUMP TEST TERMINAL LOCATION TABLE
\
\
\
\
\
\
Page 705 of 1501
Application Wire Color Location
Diamante .................. Black/Blue ............ (1)
Eclipse (Turbo & 2.4L) .... Black/Blue ............. ( 2)
Galant .................... Black/Blue ............ ( 3)
Mirage .................... Black/Blue ............ ( 1)
Montero ...................... White .............. ( 4)
3000GT .................... Black/Blue ............ ( 6)
( 1) - On firewall, above brake master cylinder.
( 2) - On firewall behind battery.
( 3) - On main wiring harness, near center of firewall.
( 4) - On main wiring harness, near right center of firewall.
( 5) - Near left rear corner of engine compartment, below
cruise control actuator (if equipped).
( 6) - On main wiring harness, near wiper motor on firewall,
behind battery.
\
\
\
\
\
\
3) Start engine and allow it to idle. Measure fuel pressure
with vacuum hose connected to fuel pressure regulator. Record fuel
pressure reading. See FUEL PUMP PERFORMANCE table. Disconnect and plug
vacuum hose from fuel pressure regulator. Record fuel pressure
reading.
4) Check for fuel pressure in fuel return hose by gently
pinching hose while increasing engine speed. If fuel volume is low,
fuel pressure in return hose will not be felt. Increase engine speed
to 2500-3000 RPM, 2-3 times. Return engine to idle. Fuel pressure
should not drop when engine is returned to idle.
5) Turn ignition off. Ensure fuel pressure reading does not
decrease within 2 minutes. If a decrease is noted, monitor speed of
decrease.
6) If fuel pressure is lower than specification, fuel
pressure drops at idle after increasing engine speed to 2500-3000 RPM,
or no fuel pressure in fuel return hose can be felt, check for clogged
fuel filter, or faulty fuel pressure regulator or fuel pump.
7) If fuel pressure is greater than specification, check for
a faulty fuel pressure regulator or plugged fuel return line. If fuel
pressure does not change when vacuum hose to regulator is connected or
disconnected, check for a leaking or clogged vacuum hose to fuel
pressure regulator or faulty fuel pressure regulator.
8) If fuel pressure decreases suddenly after engine is
stopped, check valve in fuel pump is not seated. Replace fuel pump. If
fuel pressure drops slowly, fuel injector is leaking or fuel pressure
regulator valve seat is leaking. Check for faulty fuel injector or
fuel pressure regulator. Repair as necessary.
9) When fuel pressure test is complete, repeat fuel pressure
release procedure before disconnecting fuel pressure gauge. Install
NEW "O" ring at end of high pressure fuel inlet line. Check for fuel
leaks.
FUEL PUMP PERFORMANCE TABLE
\
\
\
\
\
\
At Idle w/Vacuum At Idle w/o Vacuum
Application psi (kg/cm) psi (kg/cm)
Eclipse 2.0L
Non-Turbo ........... ( 1) ............ 47-50 (3.3-3.5)
Turbo ............. 33 (2.3) ......... 42-45 (3.0-3.5)
3000GT Turbo ........ 34 (2.4) ......... 43-45 (3.0-3.1)
All Other Models .... 38 (2.7) ......... 47-50 (3.3-3.5)
( 1) - Information is not available from manufacturer at time
Page 720 of 1501
TROUBLE CODE DEFINITION
When DTC is obtained, refer to appropriate DTC test
procedure.
DIAGNOSTIC TROUBLE CODES (DTCS)
NOTE: DTCs can only be retrieved by using a scan tool. Listed DTCs
are retrieved using a generic scan tool. MUT II scan tool
can be used, but it may not read all DTCs. DTCS listed are
not used on all vehicles.
DTC P0100
Volume Airflow (VAF) circuit failure. Possible causes are:
connector or harness, or faulty VAF sensor.
DTC P0105
Barometric (BARO) pressure circuit failure. Possible causes
are: connector or harness, or faulty BARO pressure sensor.
DTC P0105
Manifold Absolute Pressure (MAP) circuit failure. Possible
causes are: connector or harness, or faulty MAP sensor.
DTC P0110
Intake Air Temperature (IAT) circuit failure. Possible causes\
are: connector or harness, or faulty VAF sensor.
DTC P0115
Engine Coolant Temperature (ECT) circuit failure. Possible
causes are: connector or harness, or faulty ECT sensor.
DTC P0120
Throttle Position (TP) circuit failure. Possible causes are:
connector or harness, or faulty TP sensor.
DTC P0125
Excessive time to enter closed loop fuel control. Possible
causes are: faulty front HO2S, HO2S connector or harness, or faulty
fuel injector.
DTC P0130
Front Heated Oxygen Sensor (HO2S) circuit failure. Possible
causes are: connector or harness, or faulty HO2S.
DTC P0135
Front Heated Oxygen Sensor (HO2S) heater circuit failure.
Possible causes are: connector or harness, or faulty HO2S.
DTC P0136
Rear Heated Oxygen Sensor (HO2S) circuit failure. Possible
causes are: connector or harness, or faulty HO2S.
DTC P0141
Rear Heated Oxygen Sensor (HO2S) heater circuit failure.
Possible causes are: connector or harness, or faulty HO2S.
DTC P0150
Heated Oxygen Sensor (HO2S) circuit failure (bank 2, sensor
1). Possible causes are: connector or harness, or HO2S.
Page 721 of 1501
DTC P0155
Heated Oxygen Sensor (HO2S) heater circuit failure (bank 2,
sensor 1). Possible causes are: connector or harness, or HO2S.
DTC P0156
Heated Oxygen Sensor (HO2S) circuit failure (bank 2, sensor
2). Possible causes are: connector or harness, or HO2S.
DTC P0161
Heated Oxygen Sensor (HO2S) heater circuit failure (bank 2,
sensor 2). Possible causes are: connector or harness, or HO2S.
DTC P0170
Fuel trim failure (bank 1). Possible causes are: intake air
leaks, cracked exhaust manifold, faulty VAF sensor frequency, HO2S,
injector, fuel pressure, ECT, IAT or BARO pressure sensor.
DTC P0173
Fuel trim failure (bank 2). Possible causes are: intake air
leaks, cracked exhaust manifold, faulty VAF sensor frequency, HO2S,
injector, fuel pressure, ECT, IAT or BARO pressure sensor.
DTC P0201
Cylinder No. 1 injector circuit failure. Possible causes are:
connector or harness, or faulty injector.
DTC P0202
Cylinder No. 2 injector circuit failure. Possible causes are:
connector or harness, or faulty injector.
DTC P0203
Cylinder No. 3 injector circuit failure. Possible causes are:
connector or harness, or faulty injector.
DTC P0204
Cylinder No. 4 injector circuit failure. Possible causes are:
connector or harness, or faulty injector.
DTC P0205
Cylinder No. 5 injector circuit failure. Possible causes are:
connector or harness, or faulty injector.
DTC P0206
Cylinder No. 6 injector circuit failure. Possible causes are:
connector or harness, or faulty injector.
DTC P0300
Random misfire detected. Possible causes are: connector or
harness, faulty ignition coil, ignition power transistor, spark plug,
ignition circuit, injector, HO2S, compression pressure, timing belt,
air intake system, fuel pressure, or CKP sensor.
DTC P0301
Cylinder No. 1 misfire detected. Possible causes are:
connector or harness, faulty ignition coil, ignition power transistor,
spark plug, ignition circuit, injector, HO2S, compression pressure,
timing belt, air intake system, fuel pressure, or CKP sensor.
DTC P0302
Cylinder No. 2 misfire detected. Possible causes are:
connector or harness, faulty ignition coil, ignition power transistor,
spark plug, ignition circuit, injector, HO2S, compression pressure,
timing belt, air intake system, fuel pressure, or CKP sensor.