1998 MITSUBISHI MONTERO boot

\









\









\









\









\









\









\


DIP STICK TUBES
See DIP STICKS AND TUBES .
DISTRIBUTOR ADVANCES AND RETARDERS (MECHANICAL AND VACUUM)
DISTRIBUTOR ADVANCE AND RETARDER (MECHANICAL AND VACUUM) INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Binding ................. A .. Require repair or replacement.
Inoperative ............. A ........... ( 1) Require repair or
replacement.
Leaking ................. A ............ Require replacement.
Out of specification .... B .. Require repair or replacement.
( 1) - Inoperative includes intermittent operation.









\









\









\









\









\









\









\


DISTRIBUTOR BOOTS AND SHIELDS
DISTRIBUTOR BOOT AND SHIELD INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Deteriorated ............ A ............ Require replacement.
Leaking ................. A ............ Require replacement.
Missing ................. A ............ Require replacement.
Torn .................... A ............ Require replacement.









\









\









\









\









\









\









\


DISTRIBUTOR CAPS
DISTRIBUTOR CAP INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Arcing .................. A ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.

Eroded .................. 1 ............ Suggest replacement.
Loose ................... A .. Require repair or replacement.
Out of specification .... B ............ Require replacement.









\









\









\









\









\









\









\


DISTRIBUTOR SHIELDS
See DISTRIBUTOR BOOTS AND SHIELDS .
DISTRIBUTORS
DISTRIBUTOR INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Bushings worn, affecting
performance ............ A .. Require repair or replacement.
Bushings worn, not
affecting performance .. 1 .. Suggest repair or replacement.
Cam lobes worn, affecting
performance ............ A .. Require repair or replacement.
Cam lobes worn, not
affecting performance .. 1 .. Suggest repair or replacement.
Gear broken ............. A .. Require repair or replacement.
Gear worn, affecting
performance ............ A ............ Require replacement.
Gear worn, not affecting
performance ............ .. ........ No service suggested or
required.
Integrated pickup
triggering device
loose .................. A .. Require repair or replacement.
Integrated pickup
triggering device
magnetism incorrect .... A .. Require repair or replacement.
Leaking oil internally .. A .. Require repair or replacement.
Noisy ................... 2 .. Suggest repair or replacement.
Pickup triggering device
(reluctor) broken ...... A .. Require repair or replacement.
Pickup triggering device
(reluctor) loose ....... A .. Require repair or replacement.
Pickup triggering device
(reluctor) weak ........ A .. Require repair or replacement.
Reluctor (pickup
triggering device)
broken ................. A .. Require repair or replacement.
Reluctor (pickup
triggering device)
loose .................. A .. Require repair or replacement.
Reluctor (pickup
triggering device)
weak ................... A .. Require repair or replacement.
Shaft bent .............. A ............ Require replacement.
Thrust washer broken .... A .. Require repair or replacement.

Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... (1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Wire lead conductors
exposed ................ B .. Require repair or replacement.
Wire lead corroded ...... A .. Require repair or replacement.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Determine source of contamination, such as engine coolant,
fuel, metal particles, or water. Require repair or
replacement.
( 3) - Inoperative includes intermittent operation or out of
OEM specification. Some components may be serviceable;
check for accepted cleaning procedure.









\









\









\









\









\









\









\


IGNITION BOOTS
See
IGNITION WIRES, BOOTS, COIL TOWERS AND TERMINALS (SECONDARY) .
IGNITION COIL TOWERS
See
IGNITION WIRES, BOOTS, COIL TOWERS AND TERMINALS (SECONDARY) .
IGNITION COILS
IGNITION COIL INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Arcing .................. A ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........... ( 1) Require repair or

Connector missing ....... A ................. Require repair.
Contaminated ............ A ........... (3) Require repair or
replacement.
Leaking ................. A .. Require repair or replacement.
Malfunctioning .......... A ........... ( 4) Require repair or
replacement.
Missing ................. C ............ Require replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 2) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Wire lead conductors
exposed ................ B .. Require repair or replacement.
Wire lead corroded ...... A .. Require repair or replacement.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
( 1) - Refer to manufacturer's diagnostic trouble code
procedure and require repair or replacement of affected
component(s).
( 2) - Determine cause and correct prior to repair or
replacement of part.
( 3) - Determine source of contamination, such as engine
coolant, fuel, metal particles, or water. Require
repair or replacement.
( 4) - Includes inoperative, intermittent operation, or failure to
perform all functions.









\









\









\









\









\









\









\


IGNITION SWITCHES
See SWITCHES.
IGNITION TERMINALS
See
IGNITION WIRES, BOOTS, COIL TOWERS AND TERMINALS (SECONDARY) .
IGNITION WIRES, BOOTS, COIL TOWERS AND TERMINALS (SECONDARY)
NOTE: You are not required to replace ignition wires in sets.
However, you may suggest replacement of the entire
secondary wire set for preventive maintenance.
IGNITION WIRE, BOOT, COIL TOWER AND TERMINAL (SECONDARY) INSPECTION









\









\









\









\









\









\









\


Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.

\
\
\
\
\
\
\
 
REPLACE 
\b
\
\
\
\
\
\
\



 Engine Oil (
1) 
\b
 \
\
\
\
\
\
\



 Engine Oil Filter (
2) 
\b
\
\
\
\
\
\
\



(
1) - Change once a year or every 7500 miles (12,000 KM). 

(
2) - If mileage is less than 7,500 miles (12,000 KM) each year, 

replace the oil filter at every oil change. 
\b
\
\
\
\
\
\
\




LUBRICATION SPECIFICATIONS 
\b
\
\
\
\
\
\
\




Material  Condition  Specification 
\b
\
 \
\
\
 \
\
\



Engine Oil  Ambient Temperature Less Than SAE 5W-30 

(
1)  0F (-18C) To 100F (38C)  

\b
\
\
\
 \
\



Ambient Temperature Above 0F  SAE 10W-30 

 (-18C) To Over 100F (38C)  
\b
\
\
\
\
\
\
\



(
1) - SAE 5W-30 engine oil is preferred. SAE 10W-30 may be used if 

the Ambient Temperature is above 0 F (-18 C). 
\b
\
\
\
\
\
\
\




FLUID CAPACITIES 
\b
\
\
\
\
\
\
\




Item  Condition  Specification (1) 
\b
\
 \
\
\
 \
\
\



Engine Oil  Oil Pan  4.5 Qts. (4.3L) 

(
1) \b \
\
\
 \
\



 Oil Filter  0.32 Qts. (0.3L) 

\b
\
\
\
 \
\



 Oil Cooler  0.32 Qts. (0.3L) 
\b
\
\
\
\
\
\
\



(
1) - Capacities are recommended or calculated levels. Always use 

dipstick to measure level. 
\f
\
\
\
\
\
\
\


15,000 MILE (24,000 KM) NORMAL SERVICE
15,000 MILE (24,000 KM) NORMAL SERVICE
\
\
\
\
\
\
\


INSPECT 
\b
\
\
\
\
\
\
\



 Disc Brake Pads (
3) 
\b
 \
\
\
\
\
\
\



 Brake Hoses (
3) 
\b
 \
\
\
\
\
\
\



 Drive Shaft Boots (
3) 
\b
\
\
\
\
\
\
\




REPLACE 
\b
\
\
\
\
\
\
\



 Engine Oil (
1) 
\b
 \
\
\
\
\
\
\



 Engine Oil Filter (
2) 
\b
\
\
\
\
\
\
\



(
1) - Change once a year or every 7,500 miles (12,000 KM). 

(
2) - If mileage is less than 7,500 miles (12,000 KM) each year, 

replace the oil filter at every oil change. 

(
3) - Or inspect every year. 
\b
\
\
\
\
\
\
\




LUBRICATION SPECIFICATIONS 

\b\
 \
\
\
 \
\
\



Engine Oil  Oil Pan  4.5 Qts. (4.3L) 

(
1) \b \
\
\
 \
\



 Oil Filter  0.32 Qts. (0.3L) 

\b
\
\
\
 \
\



 Oil Cooler  0.32 Qts. (0.3L) 
\b
\
\
\
\
\
\
\



(
1) - Capacities are recommended or calculated levels. Always use 

dipstick to measure level. 
\f
\
\
\
\
\
\
\


30,000 MILE (48,000 KM) NORMAL SERVICE
30,000 MILE (48,000 KM) NORMAL SERVICE
\
\
\
\
\
\
\
 
VERIFY 
\b
\
\
\
\
\
\
\




Last Major Service Was Performed 
\b
\
\
\
\
\
\
\




SERVICE 
\b
\
\
\
\
\
\
\



 Ball Joints With Grease Nipple (
6) 
\b
 \
\
\
\
\
\
\



 Propeller Shaft Joints (
6) 
\b
\
\
\
\
\
\
\




INSPECT 
\b
\
\
\
\
\
\
\



 Fuel Hoses (
3) 
\b
 \
\
\
\
\
\
\



 Drive Belt (For Generator, Water Pump, Power Steering Pump) 
\b
 \
\
\
\
\
\
\



 Manual Transmission Oil 
\b
 \
\
\
\
\
\
\



 Transfer Oil 
\b
 \
\
\
\
\
\
\



 Disc Brake Pads (
4) 
\b
 \
\
\
\
\
\
\



 Brake Hoses (
4) 
\b
 \
\
\
\
\
\
\



 Ball Joint & Steering Linkage Seals (
3) 
\b
 \
\
\
\
\
\
\



 Drive Shaft Boots (
4) 
\b
 \
\
\
\
\
\
\



 Exhaust System (
3) 
\b
\
\
\
\
\
\
\




REPLACE 
\b
\
\
\
\
\
\
\



 Engine Oil (
1) 
\b
 \
\
\
\
\
\
\



 Engine Oil Filter (
2) 
\b
 \
\
\
\
\
\
\



 Engine Coolant 
\b
 \
\
\
\
\
\
\



 Automatic Transmission Fluid 
\b
 \
\
\
\
\
\
\



 Rear Axle Oil 
\b
 \
\
\
\
\
\
\



 Air Cleaner Filter 
\b
\
\
\
\
\
\
\



(
1) - Change once a year or every 7,500 miles (12,000 KM). 

(
2) - If mileage is less than 7,500 miles (12,000 KM) each year, 

replace the oil filter at every oil change. 

  Brake Hoses (3) 
\b
 \
\
\
\
\
\
\



 Drive Shaft Boots (
3) 
\b
\
\
\
\
\
\
\




REPLACE 
\b
\
\
\
\
\
\
\



 Engine Oil (
1) 
\b
 \
\
\
\
\
\
\



 Engine Oil Filter (
2) 
\b
\
\
\
\
\
\
\



(
1) - Change once a year or every 7,500 miles (12,000 KM). 

(
2) - If mileage is less than 7,500 miles (12,000 KM) each year, 

replace the oil filter at every oil change. 

(
3) - Or inspect every year. 
\b
\
\
\
\
\
\
\




LUBRICATION SPECIFICATIONS 
\b
\
\
\
\
\
\
\




Material  Condition  Specification 
\b
\
 \
\
\
 \
\
\



Engine Oil  Ambient Temperature Less Than SAE 5W-30 

(
1)  0F (-18C) To 100F (38C)  

\b
\
\
\
 \
\



Ambient Temperature Above 0F  SAE 10W-30 

 (-18C) To Over 100F (38C)  
\b
\
 \
\
\
 \
\
\



Brake Fluid  All  DOT 3 Or DOT 4 
\b
\
\
\
\
\
\
\



(
1) - SAE 5W-30 engine oil is preferred. SAE 10W-30 may be used if 

the Ambient Temperature is above 0 F (-18 C). 
\b
\
\
\
\
\
\
\




FLUID CAPACITIES 
\b
\
\
\
\
\
\
\




Item  Condition  Specification (1) 
\b
\
 \
\
\
 \
\
\



Engine Oil  Oil Pan  4.5 Qts. (4.3L) 

(
1) \b \
\
\
 \
\



 Oil Filter  0.32 Qts. (0.3L) 

\b
\
\
\
 \
\



 Oil Cooler  0.32 Qts. (0.3L) 
\b
\
\
\
\
\
\
\



(
1) - Capacities are recommended or calculated levels. Always use 

dipstick to measure level. 
\f
\
\
\
\
\
\
\


52,500 MILE (84,000 KM) NORMAL SERVICE
52,500 MILE (84,000 KM) NORMAL SERVICE
\
\
\
\
\
\
\
 
VERIFY 
\b
\
\
\
\
\
\
\




Last Major Service Was Performed 
\b
\
\
\
\
\
\
\




REPLACE 
\b
\
\
\
\
\
\
\



 Engine Oil (
1) 
\b
 \
\
\
\
\
\
\



 Engine Oil Filter (
2) 
\b
\
\
\
\
\
\
\



(
1) - Change once a year or every 7,500 miles (12,000 KM). 

(
2) - If mileage is less than 7,500 miles (12,000 KM) each year, 

replace the oil filter at every oil change. 
\b
\
\
\
\
\
\
\


\b \
\
\
\
\
\
\



 Drive Shaft Boots (
4) 
\b
 \
\
\
\
\
\
\



 Exhaust System (
3) 
\b
 \
\
\
\
\
\
\



 Distributor Cap & Rotor (
7) 
\b
\
\
\
\
\
\
\




REPLACE 
\b
\
\
\
\
\
\
\



 Engine Oil (
1) 
\b
 \
\
\
\
\
\
\



 Engine Oil Filter (
2) 
\b
 \
\
\
\
\
\
\



 Engine Coolant 
\b
 \
\
\
\
\
\
\



 Automatic Transmission Fluid 
\b
 \
\
\
\
\
\
\



 Rear Axle Oil 
\b
 \
\
\
\
\
\
\



 Spark Plugs 
\b
 \
\
\
\
\
\
\



 Timing Belt (
9) 
\b
 \
\
\
\
\
\
\



 Ignition Cables (
8) 
\b
 \
\
\
\
\
\
\



 Air Cleaner Filter 
\b
\
\
\
\
\
\
\



(
1) - Change once a year or every 7,500 miles (12,000 KM). 

(
2) - If mileage is less than 7,500 miles (12,000 KM) each year, 

replace the oil filter at every oil change. 

(
3) - Or inspect every 2 years. 

(
4) - Or inspect every year. 

(
5) - Or change every 2 years. 

(
6) - Or lubricate grease every 2 years. 

(
7) - Or inspect every 5 years. 

(
8) - Or replace every 5 years. 

(
9) - For California & Massachusettes, this maintenance is 

recommended but not required. 
\b
\
\
\
\
\
\
\




LUBRICATION SPECIFICATIONS 
\b
\
\
\
\
\
\
\




Material  Condition  Specification 
\b
\
 \
\
\
 \
\
\



Engine Oil  Ambient Temperature Less Than SAE 5W-30 

(
1)  0F (-18C) To 100F (38C)  

\b
\
\
\
 \
\



Ambient Temperature Above 0F  SAE 10W-30 

 (-18C) To Over 100F (38C)  
\b
\
 \
\
\
 \
\
\



Engine  All  50/50 Mixture Of 

Coolant   Distilled Water & 

  Ethylene Glycol 
\b
\
 \
\
\
 \
\
\



Manual  All API Classification GL-4

Transmission   SAE 75W-85W Or 75W-90 
\b
\
 \
\
\
 \
\
\



Automatic  All  "ATF DEXRON II" Or 

Transmission   Equivalent 
\b
\
 \
\
\
 \
\
\



Brake Fluid  All  DOT 3 Or DOT 4 
\b
\
 \
\
\
 \
\
\



Rear Axle  All API Classification GL-5

  Or Higher (
2)