1998 MITSUBISHI MONTERO service
[x] Cancel search: servicePage 434 of 1501
![MITSUBISHI MONTERO 1998 Service Manual Torn .................... A ............ Require replacement. \
\
\
\
\
\](/manual-img/19/57333/w960_57333-433.png "MITSUBISHI MONTERO 1998 Service Manual Torn .................... A ............ Require replacement. \
\
\
\
\
\")
Torn .................... A ............ Require replacement. \
\
\
\
\
\
\
ENGINE MOUNTS
See MOUNTS (ENGINE, TRANSAXLE AND TRANSMISSION) .
EXCITER RINGS
See TOOTHED RINGS (TONE WHEELS) .
FILLER TUBES
See DIP STICK TUBES .
FILTERS AND SCREENS
FILTER AND SCREEN INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
At service interval ..... 3 ............ Suggest replacement.
Bent .................... A .. Require repair or replacement.
Exceeding service
interval ............... 3 ............ Suggest replacement.
Missing ................. C ............ Require replacement.
Near service interval ... 3 ............ Suggest replacement.
Restricted .............. A ........... ( 1) Require repair or
replacement.
Torn .................... A ............ Require replacement.
Worn, affecting
performance (metal or
nylon screen type) ..... A .. Require repair or replacement.
( 1) - Further inspection may be required to determine the
source of restriction or contamination.
\
\
\
\
\
\
\
FLANGES
See COMPANION FLANGES .
FLEX PLATES
FLEX PLATE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bent, affecting
performance ............ A ............ Require replacement.
Bent, not affecting
performance ............ .. ........ No service suggested or
required.
Bolt or stud holes
elongated .............. B ............ Require replacement.
Broken .................. A ............ Require replacement.
Cracked ................. A ............ Require replacement.
Ring gear worn close
to the end of its
useful life ............ 1 ............ Suggest replacement.
Ring gear worn to the
extent that it no longer
Page 435 of 1501
![MITSUBISHI MONTERO 1998 Service Manual performs its intended
function ............... A ............ Require replacement.
Weights missing ......... A ............ Require replacement.
\
\](/manual-img/19/57333/w960_57333-434.png "MITSUBISHI MONTERO 1998 Service Manual performs its intended
function ............... A ............ Require replacement.
Weights missing ......... A ............ Require replacement.
\
\")
performs its intended
function ............... A ............ Require replacement.
Weights missing ......... A ............ Require replacement.
\
\
\
\
\
\
\
FLUID LEVEL INDICATORS
See DIP STICKS (FLUID LEVEL INDICATORS) .
FLUIDS AND LUBRICANTS
FLUID AND LUBRICANT INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B ........ ( 1) Require replacement.
At service interval ..... 3 ............ Suggest replacement.
Beyond service interval . 3 ............ Suggest replacement.
Burned .................. .. ......... ( 2) Further inspection
required.
Contaminated, for example,
fluid other than hydraulic
fluid present .......... A or B .... ( 3)( 4) Require service.
Exceeding service
interval ............... 3 ............ Suggest replacement.
Hydraulic fluid
incorrect .............. B ............ ( 5) Require service.
Level incorrect ......... B ..... Require correction of fluid
level.
Near service interval ... 3 ............ Suggest replacement.
Rubber master cylinder
cover gasket distorted
and gummy .............. A ............ ( 3) Require service.
Varnished ............... .. ......... ( 6) Further inspection
required.
( 1) - Determine and correct cause.
( 2) - Fluid that is burned indicates a serious problem.
Determine and correct the cause.
( 3) - If a fluid other than hydraulic fluid is present in the
hydraulic system which DOES affect the rubber parts, the
required service is to: 1) remove all components having
rubber parts from the system, 2) flush lines with
denatured alcohol or hydraulic cleaner, 3) repair or
replace all components having rubber parts, and 4) bleed
and flush with correct hydraulic fluid. (Code A)
( 4) - If a fluid other than hydraulic fluid is present in the
hydraulic system which DOES NOT affect the rubber parts,
the required service is to flush and fill with the
correct hydraulic fluid. (Code B)
( 5) - If a fluid other than specification hydraulic fluid is
present in the hydraulic system, the required service
is to flush and fill with the correct hydraulic fluid.
( 6) - Fluid that is varnished may indicate a serious problem.
Determine and correct the cause.
\
\
\
\
\
\
\
FLYWHEELS
NOTE: Clutch disc replacement does not necessitate flywheel
reconditioning, unless other conditions justify the
reason to do so.
Page 438 of 1501
![MITSUBISHI MONTERO 1998 Service Manual INTERMEDIATE SHAFT SUPPORT BEARINGS
INTERMEDIATE SHAFT SUPPORT BEARING INSPECTION \
\
\
\
\](/manual-img/19/57333/w960_57333-437.png "MITSUBISHI MONTERO 1998 Service Manual INTERMEDIATE SHAFT SUPPORT BEARINGS
INTERMEDIATE SHAFT SUPPORT BEARING INSPECTION \
\
\
\
\")
INTERMEDIATE SHAFT SUPPORT BEARINGS
INTERMEDIATE SHAFT SUPPORT BEARING INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Bearing rollers, balls or
races are worn, pitted,
noisy, or feel rough when
rotated as an assembly . A .. Require replacement of bearing
assembly.
Bracket bent, affecting
performance ............ A .. Require repair or replacement.
Bracket bent, not
affecting performance .. .. ........ No service suggested or
required.
Bracket broken, affecting
performance ............ A ............ Require replacement.
Bracket broken, not
affecting performance .. .. ........ No service suggested or
required.
Bracket corroded,
affecting performance .. A .. Require repair or replacement.
Bracket corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Bracket cracked, affecting
performance ............ A .. Require repair or replacement.
Bracket cracked, not
affecting performance .. 1 .. Suggest repair or replacement.
Bracket holes elongated,
affecting performance .. A .. Require repair or replacement.
Bracket holes elongated,
not affecting
performances) .......... .. ........ No service suggested or
required.
Bracket loose, affecting
performance ............ A .. Require repair or replacement.
Bracket loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Bracket missing ......... C ............ Require replacement.
Cracked ................. .. ........... Require replacement.
Rough (brinelling,
spalling) .............. A ............ Require replacement.
Rubber deteriorated,
affecting performance .. A ............ Require replacement.
Seized .................. A ............ Require replacement.
\
\
\
\
\
\
\
KEY INTERLOCK SYSTEMS
See
SHIFT INTERLOCK SYSTEMS (SELECTOR AND KEY INTERLOCK SYSTEMS) .
LIMITED SLIPS
Page 441 of 1501
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Broken .................. A ............ Require replacement.
Leaking (hydraulic
mount) ................. A ............ Require replacement.
Mounting hole worn,
affecting performance .. A ............ Require replacement.
Mounting hole worn, not
affecting performance .. .. ........ No service suggested or
required.
Rubber deteriorated,
affecting performance .. A ............ Require replacement.
Rubber deteriorated, not
affecting performance .. .. ........ No service suggested or
required.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
\
\
\
\
\
\
\
ODOMETER DRIVES (MECHANICAL)
See SPEEDOMETER/ODOMETER DRIVES (MECHANICAL) .
ODOMETER HEADS (MECHANICAL)
See SPEEDOMETER/ODOMETER HEADS (MECHANICAL) .
OIL PANS
See TRANSMISSION PANS .
PANS
See TRANSMISSION PANS .
PILOT HOLES
See DOWEL PINS, GUIDES AND PILOT HOLES .
PRESSURE PLATES
PRESSURE PLATE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Balance weight missing .. C ............ Require replacement.
Broken .................. A ............ Require replacement.
Contact surface
distorted .............. B ............ Require replacement.
Cracks .................. B ............ Require replacement.
Fingers bent ............ A ............ Require replacement.
Hard spots .............. B ............ Require replacement.
Page 442 of 1501
Scored .................. B ............ Require replacement.
Spring rate less than
specifications ......... B ............ Require replacement.
Worn, affecting
performance ............ A ............ Require replacement.
Worn beyond
specifications ......... B ............ Require replacement.
Worn close to the end of
its useful life ........ 1 ............ Suggest replacement.
\
\
\
\
\
\
\
PRESSURE SWITCHES
See SWITCHES.
RACES
See BEARINGS AND RACES .
RUBBER JOINTS (METALASTIC)
These joints may be found on half and/or drive shafts. They
are usually found on European vehicles featuring a three-lug drive
flange. They may be equipped with a centering ball or pin.
RUBBER JOINT (METALASTIC) INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Drive flange bent ....... A ............. Require repair or
replacement.
Drive flange damaged,
affecting performance .. A ............ Require replacement.
Rubber drive joint
cracked ................ 2 ............ Suggest replacement.
Rubber drive joint
damaged, affecting
performance ............ A ............ Require replacement.
Rubber drive joint split
between mounting holes . A ............ Require replacement.
Rubber drive joint torn at
mounting holes ......... A ............ Require replacement.
Rubber drive joint weather-
cracked ................ .. ........ No service suggested or
required.
\
\
\
\
\
\
\
SCREENS
See FILTERS AND SCREENS .
SEALS
SEAL INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Leaking ................. A ........... ( 1) Require repair or
replacement.
( 1) - Require inspection of mating and sealing surface and
repair or replace as necessary. Check vent. A plugged
Page 445 of 1501
specification .......... B .. Require repair or replacement.
Sensor housing cracked .. 2 ............ Suggest replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... (2) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Wire lead conductors
exposed ................ B .. Require repair or replacement.
Wire lead corroded ...... A .. Require repair or replacement.
Wire lead misrouted ..... B .... Require re-routing according
to vehicle manufacturer's
specifications.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
( 1) - If a sensor is not adjustable, further inspection is
required to identify and correct cause.
( 2) - Determine cause and correct prior to repair or
replacement of part.
( 3) - Determine source of contamination, such as metal particles
or water. Require repair or replacement.
( 4) - Inoperative includes intermittent operation or out of OEM
specification. Some components may be serviceable;
check for accepted cleaning procedure.
\
\
\
\
\
\
\
SPEEDOMETER-DRIVEN GEAR HOUSINGS
See SPEEDOMETER/ODOMETER DRIVES (MECHANICAL) .
SPEEDOMETER/ODOMETER DRIVES (MECHANICAL)
SPEEDOMETER/ODOMETER DRIVE (MECHANICAL) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Inoperative ............. A ........ ( 1) Require replacement.
Leaking ................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Teeth broken ............ A .. Require repair or replacement.
Page 450 of 1501
performance ............ A .. Require repair or replacement.
Fins damaged, not
affecting performance .. .. ........ No service suggested or
required.
Internal restrictions ... B .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A .. Require repair or replacement.
Tubes damaged, affecting
performance ............ A .. Require repair or replacement.
Tubes damaged, not
affecting performance .. .. ........ No service suggested or
required.
\
\
\
\
\
\
\
TRANSMISSION MOUNTS
See MOUNTS (ENGINE, TRANSAXLE AND TRANSMISSION) .
TRANSMISSION PANS
TRANSMISSION PAN INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bent, interfering with
filter or other internal
components ............. A .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
\
\
\
\
\
\
\
TRANSMISSION RANGE INDICATORS (PRNDL)
TRANSMISSION RANGE INDICATOR (PRNDL) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Binding ................. A .. Require repair or replacement.
Broken .................. A .. Require repair or replacement.
Components missing ...... C .. Require replacement of missing
components.
Loose, affecting
performance ............ A .. Require repair or replacement.
Out of adjustment ....... A ................. Require repair.
Worn, affecting
performance ............ A .. Require repair or replacement.
\
\
\
\
\
\
\
TUBES
See HOSES, LINES AND TUBES .
UNIVERSAL JOINTS (CARDON OR CROSS TYPE)
UNIVERSAL JOINT (CARDON OR CROSS TYPE) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Page 479 of 1501
* ELECTRICAL SYSTEM UNIFORM INSPECTION GUIDELINES *
1998 Mitsubishi Montero
GENERAL INFORMATION
Electrical System Motorist Assurance Program
Standards For Automotive Repair
All Makes and Models
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
CONTENTS
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
ACTUATOR MOTORS (SOLENOIDS) (ELECTRIC)
ACTUATOR MOTORS (VACUUM)
AIR BAGS
ALTERNATORS AND GENERATORS
AMPLIFIERS
ANTENNAS
BATTERIES
BATTERY CABLES
BATTERY CABLES
BATTERY HOLD DOWN HARDWARE
BATTERY TRAYS AND HOLD DOWN HARDWARE
BATTERY WIRES
BELTS
BULB SOCKETS
BULBS, SEALED BEAMS AND LEDS
CD PLAYERS
CIGARETTE LIGHTER ASSEMBLIES
CIRCUIT BREAKERS
CLUTCH SWITCHES
CONNECTORS
CONTROL MODULES
CRUISE CONTROL BRAKE SWITCHES
CRUISE CONTROL CABLES
CRUISE CONTROL CLUTCH SWITCHES
CRUISE CONTROL LINKAGES AND CABLES
CRUISE CONTROL RESERVOIRS
CRUISE CONTROL TUBES
CRUISE CONTROL VACUUM DUMP RELEASE VALVES
CRUISE CONTROL VACUUM HOSES, TUBES AND RESERVOIRS
CRUISE CONTROL VEHICLE SPEED SENSORS
DEFOGGERS
DEFROSTERS
DELAYS
DIMMERS
ELECTRIC HEATERS
EQUALIZERS
FUSE BLOCKS
FUSE BOXES AND BLOCKS
FUSES, FUSIBLE LINKS AND CIRCUIT BREAKERS
FUSIBLE LINKS
GAUGES
GENERATORS
GROUND CABLES AND STRAPS
GROUND STRAPS
HEADLIGHT ADJUSTERS
HEATING ELEMENTS (DEFROSTERS, DEFOGGERS, ELECTRIC HEATERS AND SEATS)
HORNS AND SIRENS