1998 MITSUBISHI MONTERO power steering
[x] Cancel search: power steeringPage 32 of 1501
![MITSUBISHI MONTERO 1998 Service Manual "P" ABBREVIATION TABLE
"P" ABBREVIATION TABLE \
\
\
\
\
\
\](/manual-img/19/57333/w960_57333-31.png "MITSUBISHI MONTERO 1998 Service Manual \"P\" ABBREVIATION TABLE
\"P\" ABBREVIATION TABLE \
\
\
\
\
\
\")
"P" ABBREVIATION TABLE
"P" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
"P" Park
P/C Printed Circuit
P/N Park/Neutral
P/S Power Steering
PAV Pulse Air Valve
PC-SOL Purge Control Solenoid
PCM Powertrain Control Module
PCS Purge Control Solenoid
PCSDM Passenger Compartment Sensor/Diagnostic Module
PCV Positive Crankcase Ventilation
PFE Pressure Feedback EGR sensor or circuit
PFI Port Fuel Injection (see MA SEFI)
PGM-CARB Programmed Carburetor
PGM-FI Programmed Fuel Injection
PIP Profile Ignition Pickup
PNK Pink
PPL Purple
PRNDL Park Reverse Neutral Drive Low
PROM Programmable Read-Only Memory
psi Pounds Per Square Inch
PSPS Power Steering Pressure Switch
PTC Positive Temperature Coefficient
PTO Power Take-Off
PWR GND Power Ground circuit
Pkg. Package
Press. Pressure
Prog. Programmed or Programmable
Pts. Pints
Pwr. Power
\
\
\
\
\
\
\
\f
"Q" ABBREVIATION TABLE
"Q" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
Qts. Quarts
\
\
\
\
\
\
\
\f
"R" ABBREVIATION TABLE
"R" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
RABS Rear Anti-Lock Brake System
RAC Remote Accessory Control
RAM Random Access Memory
RAP Retained Accessory Power
RECIRC Recirculation
RED Red
RH Right Hand
ROM Read Only Memory
RPM Revolutions Per Minute
Page 34 of 1501
TCC Torque Converter Clutch
TCCS Toyota Computer Control System
TDC Top Dead Center
TDCL Total Diagnostic Communication Link
TFI Thick Film Ignition system
TGS Top Gear Switch (cancels SIL in top gear)
THERMAC Thermostatic Air Cleaner
THS Transmission Hydraulic Switch
TP/TPS Throttle Position Sensor
TPI Tuned Port Injection
TPS Throttle Position Sensor/Switch
TS Temperature Sensor
TSB Technical Service Bulletin
TTS Transmission Temperature Switch
TV Thermovalve
TWC Three-Way Catalyst
Temp. Temperature
Trans. Transaxle/Transmission
\
\
\
\
\
\
\
\f
"V" ABBREVIATION TABLE
"V" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
V Valve
VAF Vane Air Flow sensor or circuit
VAPS Variable Assist Power Steering
VAT Vane Air Temperature
VATS Vehicle Anti-Theft System
VBATT Vehicle Battery Voltage
VCC Viscous Converter Clutch
VIN Vehicle Identification Number
VIO Violet
VLR Volt Loop Reserve
VM Vacuum Modulator
VM Vane Meter
VOM Volt-Ohmmeter (Analog)
VPWR Vehicle Power supply voltage (10-14 volts)
VREF Voltage Reference (ECA supplied reference voltage
VRV Vacuum Regulator Valve
VSC Vehicle Speed Control sensor or signal
VSS Vehicle Speed Sensor or signal
VSV Vacuum Switching Valve
Vac. Vacuum
Volt. Voltage
\
\
\
\
\
\
\
\f
"W" ABBREVIATION TABLE
"W" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
W/ With
W/O Without
WAC WOT A/C Cut-off switch or circuit
WAC Wide Open Throttle A/C Switch
WHT White
WOT Wide Open Throttle
YEL Yellow
Page 247 of 1501
Montero .............................. 10.0 Qts. (9.5L)
Montero Sport
2.4L
With Rear Heater .................. 9.5 Qts. (9.0L)
Without Rear Heater ............... 8.5 Qts. (8.0L)
3.0L
With Rear Heater ................ 10.6 Qts. (10.0L)
Without Rear Heater ............... 9.5 Qts. (9.0L)
3000GT ................................ 8.5 Qts. (8.0L)
Crankcase (Includes Filter)
Diamante ............................... 4.5 Qts. (4.3L)
Eclipse
Non-Turbo ............................ 4.5 Qts. (4.3L)
2.0L Turbo ........................... 4.6 Qts. (4.4L)
Galant ................................. 4.5 Qts. (4.3L)
Mirage
1.5L ................................. 3.5 Qts. (3.3L)
1.8L ................................. 4.0 Qts. (3.8L)
Montero ............................ (1) 5.0 Qts. (4.8L)
Montero Sport
2.4L ................................. 4.5 Qts. (4.3L)
3.0L ................................. 5.2 Qts. (4.9L)
3000GT
Non-Turbo ............................ 4.5 Qts. (4.3L)
Turbo ................................ 5.0 Qts. (4.6L)
Differential (SAE 80W-90/API GL-5)
Eclipse ................................... .9 Qt. (.8L)
Montero
Front ................................ 1.3 Qts. (1.2L)
Rear ................................. 3.3 Qts. (3.2L)
Montero Sport
Front ................................ 1.2 Qts. (1.1L)
Rear
2.4L ............................... 1.6 Qts. (1.5L)
3.0L ............................... 2.7 Qts. (2.6L)
3000GT ................................. 1.2 Qts. (1.1L)
Manual Transaxle (SAE 75W-85/API GL-4)
Eclipse
Non-Turbo ( 2) ........................ 2.1 Qts. (2.0L)
Turbo
AWD ................................ 2.4 Qts. (2.3L)
FWD ................................ 2.1 Qts. (2.0L)
Galant ................................. 2.3 Qts. (2.2L)
Mirage
1.5L ................................. 2.2 Qts. (2.1L)
1.8L ................................. 2.3 Qts. (2.2L)
3000GT
AWD .................................. 2.5 Qts. (2.4L)
FWD .................................. 2.4 Qts. (2.3L)
Manual Transmission (SAE 75W-85/API GL-4)
Montero ................................ 3.3 Qts. (3.2L)
Montero Sport .......................... 2.4 Qts. (2.3L)
Power Steering (Dexron-II)
3000GT W/4-Wheel Steering .............. 3.2 Pts. (1.5L)
Montero ................................ 2.2 Pts. (1.1L)
All Others .............................. 1.9 Pts. (.9L)
Transfer Case (SAE 75W-85/API GL-4)
Eclipse (AWD) ........................... 1.1 Pts. (.5L)
Montero ................................ 5.0 Pts. (2.5L)
Montero Sport .......................... 4.6 Pts. (2.3L)
3000GT .................................... .7 Pt. (.3L)
( 1) - Add .5 qt. (.3L) if oil cooler is drained.
Page 270 of 1501
COOLING SYSTEM SPECIFICATIONS & ENGINE COOLING FANS
1998 Mitsubishi Montero
1997-98 ENGINE COOLING
Mitsubishi Specifications & Electric Cooling Fans
Diamante, Eclipse, Galant, Mirage, Montero, Montero Sport,
3000GT
SPECIFICATIONS
BELT ADJUSTMENT
NOTE: Use illustration for water pump drive belt routing. See
Figs. 1-6. The terms alternator and generator are used
interchangeably.
BELT ADJUSTMENT
\
\
\
\
\
\
\
Application Deflection (1) In. (mm)
Diamante ....................................................... ( 2)
Eclipse & Galant
2.0L Non-Turbo ............................................... ( 2)
2.0L Turbo & 2.4L
Generator & Water Pump .................... 0.35-0.45 (9.0-11.4)\
Water Pump & Power Steering ................ 0.22-0.32 (5.6-8.1)\
Mirage
1.5L ........................................ 0.34-0.45 (8.6-11.4)\
1.8L ......................................................... ( 2)
Montero
A/C .......................................... 0.26-0.30 (6.6-7.6)\
Generator & Water Pump ................... ( 3) 0.22-0.26 (5.6-6.6)
Water Pump & Power Steering ................ 0.54-0.70 (13.7-17.8)\
Montero Sport
2.4L
A/C ........................................ 0.24-0.26 (6.1-6.6)\
Generator & Water Pump ................. ( 4) 0.28-0.35 (7.1-8.9)
Water Pump & Power Steering ................ 0.22-0.30 (5.6-7.6)\
3.0L
A/C ........................................ 0.22-0.26 (5.6-6.6)\
Generator & Water Pump ................. ( 3) 0.20-0.27 (5.1-6.8)
Water Pump & Power Steering .............. 0.52-0.68 (13.2-17.3)\
3000GT ......................................................... ( 3)
( 1) - With 22 lbs. (10 kg) pressure applied midway on belt run.
Values are for a used belt.
( 2) - Water pump is driven by timing belt. Timing belt deflection is
controlled by timing belt automatic tensioner.
( 3) - Measured between water pump pulley and crankshaft pulley.
( 4) - Measured between water pump pulley and generator pulley.
\
\
\
\
\
\
\
Page 297 of 1501
CRUISE CONTROL SYSTEM
1998 Mitsubishi Montero
1998 ACCESSORIES & EQUIPMENT
Mitsubishi - Cruise Control Systems
Montero
DESCRIPTION & OPERATION
WARNING: Deactivate air bag system before performing any service
operation. See AIR BAG RESTRAINT SYSTEMS article. Do not
apply electrical power to any component on steering column
without first deactivating air bag system. Air bag may
deploy.
Cruise control system is electronically and vacuum
controlled. System components include a control unit, actuator, vacuum
pump, cruise control switch, clutch pedal position switch (M/T),
cruise indicator light, diode, Park/Neutral (P/N) switch (A/T),
stoplight switch, vehicle speed sensor and A/T control unit (if
equipped).
System has self-diagnostic capability. When self-diagnostic
mode is activated, each switch and sensor is checked for defects. When
cruise control system has been canceled without using a normal cancel
method, a trouble code will be set and stored in control unit. Trouble
codes can be retrieved to help determine which circuit is
malfunctioning.
COMPONENT LOCATIONS
COMPONENT LOCATIONS TABLE \
\
\
\
\
\
Component Location
Cruise Control ECU .............. Behind Dash, On Steering
Column Bracket
Data Link Connector (DLC) ....... Under Left Side Of Dash,
Near Steering Column
Vehicle Speed Sensor ........... On Speedometer Assembly &
On Transmission
Throttle Position Sensor ........ Mounted On Throttle Body
\
\
\
\
\
\
ADJUSTMENTS
CRUISE CONTROL CABLE
Remove link protector. Loosen lock nut. Hold link "A" so that
it touches link "B". Adjust free play by turning adjusting nut until
free play is.04-.08" (1-2 mm). Tighten lock nut. See Fig. 1 or 2.
Page 319 of 1501
CRUISE CONTROL INDICATOR TEST under COMPONENT TESTS. If cruise control
indicator is defective, replace indicator. If indicator checks okay,
go to next step.
2) If cruise control indicator illuminates when cruise
control connector C-50 terminal No. 23 is grounded at harness side,
replace cruise control ECU. If indicator does not illuminate, check
combination meter connector C-12 and cruise control ECU connector C-
50. Repair as necessary. If connectors are okay and malfunction
remains, check harness between combination meter and cruise control
ECU. Repair as necessary.
Test No. 13
1) Perform stoplight switch test. See
BRAKELIGHT/STOPLIGHT SWITCH TEST under COMPONENT TESTS. If switch is
okay, go to next step. If switch is defective, replace brakelight
switch.
2) Check cruise control ECU connector C-50, stoplight switch
connector C-55 and joint connector C-131. Repair as necessary. See
Figs. 13 , 14, 16 and 29. If connectors are okay and malfunction
remains, check harness between joint connector C-131 and cruise
control ECU.
Test No. 14 (A/T)
1) Perform park/neutral switch test. See
PARK/NEUTRAL SWITCH TEST under COMPONENT TESTS. If switch is okay, go
to next step. If switch is defective, replace switch.
2) Check starter relay. Replace if defective. If relay is
okay, check cruise control ECU connector C-50 and joint connector C-
130. Repair as necessary. See Figs. 13, 16 and 28. If connectors are
okay and malfunction remains, check harness between cruise control ECU
and power supply.
COMPONENT TESTS
ACTUATOR TEST
Remove actuator. Apply vacuum to actuator. Actuator linkage
holder should move more than 1.38" (35 mm). Actuator diaphragm should
hold vacuum. Replace actuator if actuator does not test as specified.
BRAKELIGHT/STOPLIGHT SWITCH TEST
Disconnect stoplight switch connector C-55. When brake pedal
is pressed, continuity should be present between terminals No. 2 and
3. See Fig. 14. When brake pedal is released, continuity should be
present between terminals No. 1 and 4. Replace switch if it does not
test as specified.
CLOCKSPRING TEST
WARNING: Deactivate air bag system before performing any service
operation. See AIR BAG RESTRAINT SYSTEMS article. Do not
apply electrical power to any component on steering column
without first deactivating air bag system. Air bag may
deploy.
If clockspring fails any check, replace with a NEW
clockspring.
1) Check connectors and protective tube for damage and
deformities.
2) Visually check case for damage or deformities.
Page 324 of 1501
* PLEASE READ THIS FIRST *
NOTE: Self-diagnostics should be performed when cruise control
cancels without driver using normal cancel modes.
RETRIEVING CODES
1) Data Link Connector (DLC) is located to left of steering
column. Use analog voltmeter or scan tool for code retrieval. Follow
scan tool manufacturer's instructions.
2) Using an analog voltmeter, connect leads between cruise
control terminal and ground terminal of DLC. See Fig. 35. Count number
of deflections and pauses of voltmeter needle to determine trouble
code. Digit count is about 0.5 second per pulse and pause between
digits is about 2 seconds. Once trouble codes have been displayed, see
DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION table.
DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION TABLE
\
\
\
\
\
\
Code Diagnostic Item
11 .............................. Vacuum Pump Drive System
12 ........................... Vehicle Speed Sensor Signal
14 ....................... Vacuum Pump Power Supply System
15 ................................. Cruise Control Switch
16 .................................... Cruise Control ECU
17 ....................... Throttle Position Sensor System
\
\
\
\
\
\
Fig. 35: Identifying Data Link Connector Terminals
Courtesy of Mitsubishi Motor Sales of America
CLEARING CODES
Page 329 of 1501
* PLEASE READ THIS FIRST *
WARNING: Deactivate air bag system before performing any service
operation. See AIR BAG RESTRAINT SYSTEMS article. Do not
apply electrical power to any component on steering column
without first deactivating air bag system. Air bag may
deploy.
ACTUATOR
Removal & Installation
Disconnect cruise control cable from link. Disconnect
actuator wiring connector. Remove vacuum pump and vacuum pump bracket.
Remove actuator and actuator bracket. To install, reverse removal
procedure.
CRUISE CONTROL ECU
Removal & Installation
Cruise control ECU is located behind center of dash panel.
Remove center trim panel and radio or radio plug bezel. Remove control
unit. To install, reverse removal procedure.
CRUISE CONTROL SWITCH
Removal & Installation
Remove lower steering column cover. Disconnect electrical
connectors. Remove screws attaching cruise control switch to steering
column. Remove switch. To install, reverse removal procedure.
INSTRUMENT CLUSTER
Removal & Installation
Disconnect negative battery cable. Remove cluster cover.
Disconnect speedometer cable. Remove instrument cluster. To install,
reverse removal procedure.
WIRING DIAGRAMS