1998 MITSUBISHI LANCER EVOLUTION IV belt

ENGINE ELECTRICAL – Charging System16-3
REMOVAL SERVICE POINTS

APOWER STEERING, A/C COMPRESSOR, AND
ALTERNATOR DRIVE BELT REMOVAL
(1) Align the hole in the auto tensioner bracket with that
in the arm and insert a screwdriver into the holes.
(2) Remove the drive belt.

BDELIVERY PIPE, INJECTOR, AND PRESSURE
REGULATOR ASSEMBLY REMOVAL
After the mounting points have been loosened, slightly move
the corresponding part to allow for a space for removal of
the alternator.

CALTERNATOR REMOVAL
Push the engine all the way up with a garage jack and remove
the alternator upward the engine compartment.
Phillips
screwdriver
Hole in arm
Auto tensioner
Hole in bracket

ENGINE ELECTRICAL – Ignition System16-5
CAMSHAFT POSITION SENSOR AND CRANK ANGLE SENSOR
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
Timing Belt Removal and Installation
(Refer to GROUP 11.)
Unit: Nm {kgf
m}
49 {5.0}
5
9 {0.9}9 {0.9}
9 {0.9} 39 {4.0} 3 {0.3}
2
3
41
Removal steps
1. Camshaft position sensor
2. Center cover

A3. Power steering oil pump4. Power steering oil pump bracket
5. Crank angle sensor
REMOVAL SERVICE POINT

APOWER STEERING OIL PUMP REMOVAL
Remove the power steering oil pump with hose from the power
steering oil pump bracket.
NOTE
String up the oil pump which has been removed onto a location
that does not hamper removal and installation of the power
steering oil pump bracket.

37A-1
STEERING
CONTENTS
SERVICE SPECIFICATIONS 2. . . . . . . . . . . . . .
SPECIAL TOOLS 2. . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE 2. . . . . . . . . . . . . . . . . .
1. Steering Angle Check 2. . . . . . . . . . . . . . . . .
2. Oil Pump Belt Tension Check and
Adjustment 2. . . . . . . . . . . . . . . . . . . . . . . . . . .
STEERING WHEEL
3. . . . . . . . . . . . . . . . . . . .
POWER STEERING GEAR & LINKAGE 3. . .
POWER STEERING OIL PUMP 7. . . . . . . . . . .
POWER STEERING FLUID COOLER 9. . . . .

STEERING – Service Specifications / Special Tools / On-vehicle Service37A-2
SERVICE SPECIFICATIONS
ItemsStandard value
Steering angleEVOLUTION-IVInner wheel33
30’ ± 2

Outer wheel28
20’
EVOLUTION-VInner wheel33
10’ ± 2

Outer wheel28
10’
Steering gearPinion total turning torque
Nm {kgfcm}
Total turning torque0.9 – 1.7 {9 – 17}
Nm {kgf
cm}Torque fluctuations0.4 {4} or less
SPECIAL TOOLS
ToolNumberNameUse
MB991197Installer barPressfitting of gear housing oil seal
MB991199Oil seal installer
MB991214Oil seal protectorInstallation of rack assembly
ON-VEHICLE SERVICE
1. STEERING ANGLE CHECK
Locate front wheels on turning radius gauge and measure
steering angle.
Standard value:
Inner wheel
33
30’ ± 2

33
10’ ± 2

Outer wheel
28
20’
28
10’
When the angle is not within the standard value, the toe
is probably incorrect. Adjust toe (Refer to GROUP 33A –
On-vehicle Service) and recheck steering angle.
2. OIL PUMP BELT TENSION CHECK AND
ADJUSTMENT
Refer to GROUP 11 – Engine Adjustments.

STEERING – Power Steering Oil Pump37A-7
POWER STEERING OIL PUMP

REMOVAL AND INSTALLATION
Pre-removal Operation
Power Steering Fluid DrainingPost-installation Operation
(1) Power Steering Fluid Supplying
(2) Drive Belt Tension Adjusting
(Refer to GROUP 11 – On-vehicle Service.)
12 3
4 5
6 7
8 9 10
Unit: Nm {kgf
m}
49 {5.0}
59 – 69
{6.0 – 7.0} 10 – 12
{1.0 – 1.2}39 {4.0}
49 {5.0}
18 {1.8}
12 {1.2}
39 {4.0}
Removal steps
1. Drive belt
2. Pressure switch connector
3. Suction hose
4. Pressure hose
5. O-ring6. Heat protector
7. Bolt
8. Bolt
9. Oil pump assembly
10. Oil pump bracket

STEERING – Power Steering Oil Pump37A-8

REMOVAL AND INSTALLATION
Pre-removal Operation
Power Steering Fluid DrainingPost-installation Operation
(1) Power Steering Fluid Supplying
(2) Drive Belt Tension Adjusting
(3) Power Steering Fluid Line Bleeding
12
34
56
7
8 9 10
Unit: Nm {kgf
m}
22 {2.2}
11
22 {2.2}
52 {5.3}24 {2.4} 12 {1.2}
18 {1.8}
Removal steps
1. Drive belt
2. Suction hose
3. Pully
4. Pressure hose
5. O-ring
6. Heat protector A7. Heat protector B
8. Pressure switch connector
9. Bolt
10. Bolt
11. Oil pump assembly