1998 Mercury Villager brake

Trailer Tow Module (If equipped)
The trailer tow module on your vehicle (if equipped) allows
turn/stop lamp control on a trailer being towed by your vehicle.
The trailer tow package includes:
mtrailer tow module which is protected by the vehicle stop
lamp fuse
mone SAE J1239 specified connector
mone extension harness within the rear bumper
mheavy duty battery
mfull size spare
If you need further assistance in wiring a trailer to your vehicle,
contact your Ford or Lincoln-Mercury dealer.
Driving While You Tow
Be especially careful when driving while you tow a trailer. Never
drive faster than 45 mph (70 km/h) when you tow in hilly
country on hot days. Also, anticipate stops so that you can brake
gradually.
If you use the speed control while you are towing on very long,
steep grades, the speed control may shut off automatically.
This is caused by the decrease of vehicle speed 5 mph (8 km/h)
lower than set speed.
When descending a steep grade with a trailer, operate in Drive
rather than Overdrive. If additional braking is needed, shift into 2
(Second) or 1 (First) gear.
Servicing Your Vehicle If You Tow
If you tow a trailer for a long distance, your vehicle will need to
be serviced more frequently than usual. See theMaintenance
Schedulebooklet in the Owner's portfolio.
236

Trailer Towing Tips
Before starting on a trip, practice turning, stopping and backing
in an area away from heavy traffic. Get to know the ªfeelº of
the vehicle/trailer combination.
Practice backing up. Back up very slowly, with someone outside
at the rear of your trailer to guide you. Place your hand at
the bottom of the steering wheel and move it in the direction you
want the rear of the trailer to swing. Slight movement of the
steering wheel results in a much larger movement of the rear of
the trailer.
When turning, drive slightly beyond the normal turning point so
the trailer wheels will clear curbs or other obstructions.
Allow more room for stopping with a trailer attached. Trailer
brakes should be applied first, whether manually or automatically
controlled, when approaching a stop.
For an easy-to-operate vehicle/trailer combination, the trailer
tongue load should be approximately 10-15% of the loaded trailer
weight.
Make a thorough check of your equipment before starting out on
the road. After you have traveled about 50 miles (80 km), stop
in a protected area and double-check your hitch and electrical
connections. Also check trailer wheel lug nuts for tightness.
When stopped in traffic for long periods of time in hot weather,
place the gearshift selector lever in Park (P) to increase the
engine idle speed. This aids in engine cooling and air conditioner
efficiency. If the engine overheats, press the air intake selector
button to select the fresh air position to stop the air conditioner
compressor. Increase the engine speed for a short time.
Vehicles with trailers should not be parked on a grade. However,
if you must park on a grade, place wheel chocks under the
trailer's wheels as follows:
Driving
237

1. Apply the main brake pedal with your foot and hold it.
2. Have another person place the wheel chocks under the trailer
wheels.
3. With the chocks in place, release the brake pedal, making sure
the chocks are holding.
4. Apply the parking brake by pressing the main brake pedal
down firmly with your right foot while depressing the
parking brake pedal with your left foot.
5. Shift the gearshift lever into P (Park).
To start, after being parked on a grade:
1. Apply the main brake pedal with your foot and hold it.
2. Start the engine.
3. Shift the gearshift lever into gear and release the parking
brake.
4. Release the main brake pedal and move the vehicle uphill to
free the wheel chocks.
5. Apply the main brake pedal and hold while another person
retrieves the chocks.
238

Hazard Flasher Switch
The hazard flasher is used to alert other drivers to hazardous
situations.
The hazard flasher switch operates the same lamps as the turn
signal lever. When the hazard flasher is activated, all of these lamps
will flash on and off. The turn signal indicators cannot be used
when the hazard lamps are flashing. Operation of the hazard
flashers does not affect operation of the brakelamps.
The flashers work even with the key out of the ignition. The
flashers will work for up to two hours when the battery is fully
charged and in good condition. They will not drain the
battery excessively. If the flashers run for longer than two hours
or if your battery is not fully charged, your battery may be
drained to the point where the vehicle will not start.
The hazard flasher switch is located on the instrument panel to
the right of the instrument cluster.
Roadside Emergencies
241

Changing a Flat Tire
If you get a flat tire while you are driving, do not apply the
brake heavily. Instead, gradually decrease the speed. Hold the
steering wheel firmly and slowly move to a safe place on the side
of the road. Park on a level spot, turn off the ignition, set the
parking brake, and turn on the hazard flashers.
The Temporary Spare Tire
Your vehicle has a temporary spare tire (unless you ordered the
optional full-size spare tire). This spare tire is smaller than a
regular tire and is designed for emergency use only. Use it only
when you get a flat tire and replace it as soon as you can. This spare
tire is marked with the words TEMPORARY USE ONLY so
that you can easily identify it.
WARNING
If you use the temporary spare tire continuously or do not
follow these precautions, the tire could fail, causing
you to lose control of the vehicle, possibly injuring yourself
or others.
When you drive with the temporary spare tire, DO NOT:
mexceed 50 mph (80 km/h) under any circumstances
mload your vehicle so that it is heavier than the maximum
vehicle load rating listed on the tire decal
mtow a trailer
muse tire chains
mtry to repair the temporary spare tire or remove it from its
wheel
muse the wheel for any other type of vehicle
254

Stowing the spare tire
1. To raise the tire to the stowed position, lay the tire on the
ground with the inboard side facing up. Install the retainer
through the wheel center and slide the tire under the
vehicle. Fit the hex-shaped end of the lug wrench over the hex
nut in the floor of the cargo area. Turn the lug wrench
clockwise until the tire is raised to its original position
underneath the vehicle.
NOTE: The lug wrench ratchets when the tire is raised to the
stowed position. It will not allow you to over-tighten.
2. Check for proper seating against the underbody supports and
retighten if necessary.
WARNING
Make sure the spare tire and jacking equipment are
stowed and secured in the proper storage location.
Preparing to Change the Tire
You should only raise your vehicle with a jack properly placed at
the front or rear jacking points.
1. Make sure that your vehicle will not move or roll and that the
tires and jack are on a level, solid surface. Put the gearshift
lever in P (Park). Set the parking brake and block the wheel Ð
in both directions Ð that is diagonally opposite the tire that
you are changing.
WARNING
When one of the front wheels is off the ground, the
transaxle alone will not prevent the vehicle from moving
or slipping off the jack, even if the vehicle is in P
(Park).
258

WARNING
To prevent the vehicle from moving when you change a
tire, be sure the parking brake is set, then block (in both
directions) the wheel that is diagonally opposite (other
side and end of the vehicle) to the tire being changed.
WARNING
If the vehicle slips off the jack, you or someone else could
be seriously injured.
2. Remove the spare tire and jack. See previous section for
instructions on spare tire removal. The jack is located in the rear
storage compartment in the right door panel of the cargo
area. You will have to unfasten the jack before removing it as
shown in the illustration. The jack handle is in the tool kit
located behind the jack.
NOTE: All occupants should be out of the vehicle while it is
on the jack.
Roadside Emergencies
259

To avoid damaging your vehicle or your battery, and to avoid
injury to yourself, follow these directions for preparing your vehicle
to jump-start and connecting the jumper cables in the order
they are given. If in doubt, call for road service.
Preparing Your Vehicle
1. Your vehicle has a 12-volt starting system, so you need to use
a 12-volt jumper system. You will damage your starting
motor, ignition system, and other electrical parts if you connect
them to a 24-volt power supply (either two 12-volt batteries
in series or a 24-volt generator set).
2. Do not disconnect the battery of the disabled vehicle. You
could damage the vehicle's electrical system.
3. Park the booster vehicle close to the hood of the disabled
vehicle.Make sure the vehicles do not touch each other.Set the
parking brake on both vehicles and stay clear of the engine
cooling fan and other moving parts.
4. Check all battery terminals and remove any excessive
corrosion before you attach the jumper cables.
5. Turn on the heater blower in both vehicles. Turn off all other
switches and lights in both vehicles to prevent possible
damage to either vehicle's electrical systems.
Roadside Emergencies
269