Page 98 of 400

Accelerating With the Speed Control Operating
To pass another vehicle while the speed control is activated, press
the accelerator pedal. When you release the pedal, the vehicle
will return to the previously set speed.
Driving Uphill or on a Steep Grade
The vehicle may not maintain the set speed when going up or
down steep hills. If this happens, drive without the speed control.
When driving uphill, especially with a heavy load, you may
notice your speed decreasing, even if you have the speed control
set. If the speed drops more than 5 mph (8 km/h), it is
normal for the automatic speed control feature to be cancelled.
You may need to help your vehicle maintain the desired speed by
driving without the speed control when driving up steep
grades.
Cancelling the Speed Control
To cancel the preset speed, follow one of these three methods:
mPush the CANCEL button on the left side of the steering wheel;
the CRUISE light will go out.
mTap the brake pedal; the CRUISE light will go out.
mPress the main OFF switch to the left of the steering wheel.
Both the CRUISE CONT. ON switch indicator and the
CRUISE light in the instrument cluster will go out.
If you unintentionally press the brake pedal while pushing the
RES/ACCEL button to reset the cruising speed, press the OFF
switch once and then reactivate the system by pressing the
CRUISE CONT. ON switch.
The speed control will automatically be canceled if the vehicle
slows down approximately 5 mph (8 km/h) below the set speed.
94
Page 99 of 400

Resetting the Speed Control
To reset at a higher speed, use one of the following methods:
mPress the accelerator pedal. When the speedometer indicates
the desired speed, push and release the COAST/SET button.
mPush and hold the RES/ACCEL button. When the vehicle attains
the speed you desire, release the switch.
mPush, then quickly release the RES/ACCEL button. Each time
you do this, the set speed will increase by about 1 mph (1.6
km/h).
To reset at a lower speed, use one of the following methods:
mLightly tap the brake pedal. When the speedometer indicates
the desired speed, push the COAST/SET button and release
it.
mPush and hold the COAST/SET button. Release the button
when the vehicle slows down to the desired speed.
mPush, then quickly release the COAST/SET button. Each time
you do this, the set speed will decrease by about 1 mph (1.6
km/h).
Resuming a Set Speed
To resume the preset speed, push and release the RES/ACCEL
button. The vehicle will resume the last set speed as long as the
vehicle is traveling at a speed over 30 mph (48 km/h).
Information About the Speed Control System
If the speed control system malfunctions, it will cancel
automatically. The CRUISE indicator in the instrument cluster
will then blink to warn the driver.
Controls and Features
95
Page 213 of 400

NOTE: Your vehicle has an interlock that prevents you from
shifting out of P (Park) unless your foot is on the brake
pedal.
If the engine does not start after two attempts:
1. Turn the ignition key to the OFF position.
2. Press the accelerator all the way to the floor and hold it.
3. Turn the ignition key to the START position.
4. Release the ignition key when the engine starts.
5. Release the accelerator gradually as the engine speeds up.
If the engine still does not start, the fuel pump shut-off switch may
have been activated. For directions on how to reset the switch
seeFuel Pump Shut-Off Switchin the index.
A computer system controls the engine's idle speed. When you
start your vehicle, the engine's idle speed normally runs high.
These faster engine speeds will make your vehicle coast
slightly faster than its normal idle speed. It should, however,
slow down after a short time. If it does not, have the idle speed
checked.
If the engine idle speed does not slow down automatically, do
not allow your vehicle to idle for more than 10 minutes. Have the
vehicle checked.
WARNING
Extended idling at high engine speeds can produce very
high temperatures in the engine and exhaust system,
creating the risk of fire or other damage.
Starting
209
Page 215 of 400
Once the shut-off switch is activated, you must reset the switch
by hand before you can start your vehicle.
The fuel pump shut-off switch reset button is located below the
hood release handle.
WARNING
If you see or smell fuel, do not reset the switch or try to
start your vehicle. Have all the passengers get out of the
vehicle and call the local fire department or a towing
service.
If your engine cranks, but does not start after a collision:
1. Turn the key in the ignition to the OFF position.
2. Check under the vehicle for leaking fuel.
3. If you do not see or smell fuel, push the fuel pump shut-off
reset button down. If the red button is already set, you may
have a different mechanical or electrical problem.
4. Turn the ignition key to the ON position for a few seconds,
then turn it to the OFF position.
Fuel pump shut-off switch reset button location
Starting
211
Page 246 of 400
To use the hazard flasher:
1. Push the HAZARD switch; you will see the turn signal arrows
flash.
2. To stop the hazard flashers, push the HAZARD switch again.
Fuel Pump Shut-Off Switch
If the engine cranks but does not start or if you have had a
collision, the fuel pump shut-off switch may have been triggered.
The shut-off switch is a device that stops the fuel pump when
your vehicle has been involved in a substantial jolt.
For information on how to check and reset the fuel pump
shut-off switch, seeWhat to do if engine does not startin the Index.
Hazard flasher switch location
242
Page 256 of 400
Circuit Breakers
The circuit breakers will reset themselves and allow the electrical
parts to work again once the overload on the circuit is
removed. If the circuit breakers continue to cut off electricity,
have your vehicle's electrical system checked.
If you have questions about circuit breakers or how to check
them, see your Lincoln-Mercury dealer.
If you replace a circuit breaker, use one with the same amperage
rating. To remove a circuit breaker mounted by the fuse
panel, grip it with your finger and thumb and pull it straight out
of its socket.
252
Page 319 of 400

Do not drive your vehicle if it does not operate properly. See
your dealer if the engine runs on for more than five seconds after
you shut it off or if it misfires, surges, stalls, or backfires.
Information about your vehicle's emissions control system is on
the Vehicle Emission Control Information decal located on or
near the engine. This decal identifies engine displacement and gives
some tune-up specifications.
How to Prepare Your Vehicle for
Inspection/Maintenance (I/M) Testing
In some localities it may be a legal requirement to pass an I/M
test of the on-board diagnostic (OBD-II) system. If your``Service
Engine Soon''light is on, reference the applicable light
description in the Warning Light and Gauges section of your
owners guide. Your vehicle may not pass the I/M test with the
``Service Engine Soon''light on.
If the vehicles powertrain system or battery has just been
serviced, the OBD-II system is reset to a ``not ready for I/M test''
condition. To ready the OBD-II system for I/M testing, a
minimum of 30 minutes of city and highway driving is necessary
as described below:
mFirst, at least ten minutes of driving on an expressway or
highway.
mNext, at least twenty minutes of driving in stop-and-go,
city-type driving with at least four idle periods.
Allow the vehicle to sit for at least 8 hours without starting the
engine. Then, start the engine and complete the above driving cycle.
The engine must warm up to it's normal operating
temperature. Once started, do not turn off the engine until the
above driving cycle is complete.
Maintenance and Care
315
Page 392 of 400

changing the tire..................254, 258
conventional spare..................254, 255
finding the spare.....................255
removing the spare tire..................255
storing the flat tire....................255
temporary spare.....................254
Spark plugs, specifications.................337
Specification chart, lubricants................339
Speed control
accelerating........................94
canceling a set speed...................95
resetting..........................95
resuming a set speed...................95
tap up/tap down.....................95
when towing a trailer..................236
Speedometer.........................19
Starting your vehicle
preparing to start your vehicle..............207
starting a cold engine..................208
starting after a collision.................242
Steering, power.......................220
Steering wheel
locking..........................86
tilting...........................91
Storage compartments...................126
cargonet .........................111
map pockets.......................126
Storing your vehicle....................333
Supplemental air bag readiness light.............11
Supplemental Restraint System (SRS)............144
T
Tachometer.........................21
mechanical cluster.....................21
388