1998 LINCOLN TOWN CAR lock

operating range will allow you to
be up to 10 meters (33 feet) away
from your vehicle. A decrease in
operating range can be caused by:
²battery weakness due to time
and use
²weather conditions
²nearby radio towers
²structures around the vehicle
²other vehicles parked next to
the vehicle
To replace the battery:
1. Twist a thin coin between the
two halves of the transmitter near
the key ring. DO NOT TAKE THE
FRONT PART OF THE
TRANSMITTER APART.
2. Place the positive (+) side of
new battery in the same
orientation. Refer to the diagram
inside the transmitter unit.
3. Snap the two halves back
together.
Replacing lost transmitters
Take all your vehicle's transmitters
to your dealer for reprogramming
if:
²a transmitter is lost or
²you want to purchase additional
transmitters (up to four may be
programmed).
To reprogram the transmitters,
place the key in the ignition and
switch from OFF to ON four times
in rapid succession within 3
seconds. After doors lock/unlock,
Controls and features
56

press any button on all
transmitters (up to four). When
completed, switch the ignition to
OFF.
All transmitters must be
programmed at the same time.
Illuminated entry
The interior lamps illuminate when
the remote entry system is used to
unlock the door(s) or sound the
personal alarm.
The system automatically turns off
after 25 seconds or when the
ignition is turned to the START or
ACC position. The dome lamp
switch (if equipped) mustnotbe
set to the OFF position for the
illuminated entry system to
operate.
The inside lights will not turn off
if:
²they have been turned on with
the dimmer control or
²any door is open.
Battery saver will shut off the
interior lamps 30 minutes after the
last door is closed.
Autolock
The autolock feature will lock all of
the doors when:
²all vehicle doors are fully closed
²the ignition key is turned to the
ON position
²the vehicle is in a forward gear
and
Controls and features
57

²you exceed 5 km/h (3 mph).
The autolock feature repeats when:
²the ignition key remains in the
ON position
²a door is opened and then
closed
²the vehicle is in a forward gear,
and
²you exceed 5 km/h (3 mph).
Autolock can also be activated or
deactivated using the following
procedure:
You must complete steps 1 through
5 within 30 seconds or the
procedure will have to be
repeated. If the procedure needs
to be repeated, you must wait 30
seconds.
1. Turn the ignition key to ON.
2. Press the power door unlock
control three times.
3. Turn the ignition key from ON
to OFF.
4. Press the power door unlock
control three times.
5. Turn the ignition key back to
ON. The doors will lock and
unlock.
6. Press the power door unlock
switch. The horn will chirp once
upon successful toggling of the
Autolock feature.
7. Turn ignition to OFF. The horn
will chirp to confirm procedure is
complete.
Controls and features
58

Memory seat/mirrors feature
(if equipped)
The remote keyless entry system
can also control the memory
seats/mirrors feature. With this
feature, the first two programmed
transmitters will recall a different
memory position.
Press the control once to unlock
the driver's door and move the
memory features to the
corresponding memory position,
just as if you had pressed the
memory control in the vehicle.
²transmitter #1 will recall
memory feature position one.
²transmitter #2 will recall
memory feature position two.
²If a third or fourth transmitter is
added, it will not recall a
memory position.
Memory seat positions can be
changed at any time. Transmitter
#1 will always move the memory
features to position #1.
Reactivating the memory
seat/mirrors feature
The remote memory seat/mirrors
feature comes disabled from the
factory. The following sequence
will reactivate the transmitter:
1. Press the SET control.
2. Press any button on the remote
entry transmitter.
3. Within five seconds, press
control one or two.
SET
12
Controls and features
59

Deactivating the memory
seat/mirrors feature
1. Press the SET control.
2. Press any button on the remote
entry transmitter.
3. Within five seconds, press the
SET control again.
Manually moving any seat or
mirror during these steps will
cancel the programming
procedure.
SECURILOCKYANTI-THEFT
SYSTEM
The SecuriLockyanti-theft system
provides an advanced level of
vehicle theft protection. Your
vehicle's engine can only be started
with the two special SecuriLocky
electronically coded keys provided
with your vehicle. Each time you
start your vehicle, the
SecuriLockykey is read by the
SecuriLockyanti-theft system. If
the SecuriLockykey identification
code matches the code stored in
the SecuriLockyanti-theft system,
the vehicle's engine is allowed to
start. If the SecuriLockykey
identification code does not match
the code stored in the system or if
a SecuriLockykey is not detected
(vehicle theft situation), the
vehicle's engine will not operate.
Spare SecuriLockykeys can be
purchased from your dealership
and programmed to your
SecuriLockyanti-theft system.
Refer toProgramming spareSET
12
Controls and features
60

SecuriLockykeysfor more
information.
If one or both of your SecuriLocky
keys are lost or stolen and you
want to ensure the lost or stolen
key will not operate your vehicle,
bring your vehicle and all available
SecuriLockykeys to your
dealership for reinitialization.
Theft indicator
The theft indicator on top of the
instrument panel will operate as
follows:
²When the ignition is OFF, the
theft indicator will flash briefly
every 2 seconds to indicate the
SecuriLockysystem is
protecting your vehicle.
²When the ignition is turned to
RUN or START, the theft
indicator will light for 3 seconds
and then go out. If the theft
indicator stays on for an
extended period of time or
flashes rapidly, have the system
serviced by your dealership or a
qualified technician.
Programming spare
SecuriLockYkeys
Spare SecuriLockykeys can be
purchased from your dealership
and programmed to your
SecuriLockyanti-theft system (up
to a total of 8 keys). Your
dealership can program your new
SecuriLockykey(s) to your
vehicle or you can do it yourself
using the following simple
Controls and features
61

procedure. To program a new
SecuriLockykey yourself, you will
need two previously programmed
SecuriLockykeys (keys that
already operate your vehicle's
engine). If two previously
programmed SecuriLockykeys are
not available (one or both of your
original keys were lost or stolen),
you must bring your vehicle to
your dealership to have the spare
SecuriLockykey(s) programmed.
Procedure to program spare
SecuriLockYkeys to your
vehicle
New SecuriLockykeys must have
the correct mechanical key cut for
your vehicle.
Conventional (non-SecuriLocky)
keyscannotbe programmed to
your vehicle.
You will need to have two
previously programmed
SecuriLockykeys and the new
unprogrammed SecuriLockykey
readily accessible for timely
implementation of each step in the
procedure. Please read and
understand the entire procedure
before you begin.
1. Insert the first previously
programmed SecuriLockykey into
the ignition switch and turn the
ignition from OFF to RUN
(maintain ignition in RUN for at
least one second).
2. Turn ignition to OFF and
remove the first SecuriLockykey
from the ignition switch.
Controls and features
62

3. Within five seconds of turning
the ignition to OFF, insert the
second previously programmed
SecuriLockykey into the ignition
switch and turn the ignition from
OFF to RUN (maintain ignition in
RUN for at least one second but no
more than 5 seconds).
4. Turn the ignition to OFF and
remove the second SecuriLocky
key from the ignition switch.
5. Within 10 seconds of turning the
ignition to OFF, insert the
unprogrammed SecuriLockykey
(new key) into the ignition switch
and turn the ignition from OFF to
RUN (maintain ignition switch in
RUN for at least one second). This
step will program your new
SecuriLockykey.
6. If it is desired to program
additional SecuriLockykey(s),
repeat this procedure from step 1.
If the programming procedure was
successful, the new SecuriLocky
key(s) will start the vehicle's
engine. The theft indicator (located
on the instrument panel) will light
for three seconds and then go out.
If the programming procedure was
not successful, the new
SecuriLockykey(s) will not
operate the vehicle's engine. The
theft indicator will flash on and off.
Wait at least one minute and then
repeat the procedure from step 1.
If failure repeats, bring your
vehicle to your dealership to have
the spare SecuriLockykey(s)
programmed.
Controls and features
63