1998 LINCOLN MARK VIII ignition

P5
0 123
4
6
7 RPMx1000H
C20406080
100
120
1404080120
200160
MPHkm/hFUEL
FILL DOOR
F
E
BRAKE888888.80
R
N
D
2
1
ABSPREMIUM FUEL
RECOMMENDED
OFFAUTO LAMP
DELAYPPANEL
DIM
INT
TIMEHILOINTOFFMISTON
OFFRESSETACCEL
COAST
Headlamp control
(pg. 32)
Speed control
(pg. 43) Driver side
air bag
(pg. 77) Turn signal and
wiper/washer
control
(pg. 41)Instrument
cluster
(pg. 6)
Ignition switch
(pg. 40) Instrument panel
dimmer switch
(pg. 33)
Instrumentation
4

WARNING LIGHTS AND CHIMES
Anti-lock brake system (ABS)
Momentarily illuminates when the
ignition is turned to the ON position
and the engine is off. If the light
remains on, continues to flash or
fails to illuminate, have the system
serviced immediately.
Brake system warning
Momentarily illuminates when the
ignition is turned to the position ON
and the engine is off. Also
illuminates when the parking brake
is engaged. Illumination after
releasing the parking brake indicates
low brake fluid level.
P
5
0 123
4
6
7
RPMx1000
H
C20406080
100
120
1404080120
200160
MPHkm/hFUEL
FILL DOOR
F
E
BRAKE000000.00
R
N
D
2
1
ABSCRUISE
ONPREMIUM FUEL
RECOMMENDED
ABS
!
BRAKE
Instrumentation
6

Engine oil pressure
Illuminates when the oil pressure
falls below the normal range. Stop
the vehicle as soon as safely
possible and switch off the engine
immediately. Check the oil level and
add oil if needed. Refer toEngine
oilin theMaintenance and Care
chapter.
This lamp also illuminates when the ignition is turned to ON and the
engine is off.
Charging system
Momentarily illuminates when the
ignition is turned to the ON position
and the engine is off. The light also
illuminates when the battery is not
charging properly, requiring
electrical system service.
Traction ControlYactive
This light momentarily illuminates
when the ignition is turned to ON. It
also illuminates when the Traction
Controlysystem begins applying
and releasing the brakes and
adjusting the engine characteristics
to limit a wheelspin condition. It will
be lit for a maximum of four
seconds or for the duration of the Traction Controlyevent.
For more information, refer to theDrivingchapter.
Instrumentation
7

Speed control (if equipped)
This light comes on when either the
SET/ACCEL or RESUME controls
are pressed. It turns off when the
speed control OFF control is
pressed, the brake is applied or the
ignition is turned to the OFF
position.
High beams
Illuminates when the high beam
headlamps are turned on.
Redundant electronic gearshift indicator
These lights operate with the key in
the ON position only and display the
same gear selection as shown on the
gear selector indicator located on
the floor console next to the
gearshift lever.
Turn signal
Illuminates when the left or right
turn signal or the hazard lights are
turned on. If one or both of the
indicators stay on continuously or
flash faster, check for a burned-out
turn signal bulb. Refer toExterior
bulbsin theMaintenance and care
chapter.
CRUISE
ON
P
R
N
D
2
1
Instrumentation
8

Message center warning lights
The following warning lights are displayed directly above the message
center controls.
Safety belt
Illuminates when the ignition is
turned on to remind you to fasten
your safety belts. For more
information, refer to theSeating
and safety restraintschapter.
Check engine
Your vehicle is equipped with a
computer that monitor's the engine's
emission control system. This
system is commonly known as the
On Board Diagnostics System (OBD
II). This OBD II system protects the
environment by ensuring that your
vehicle continues to meet
government emission standards. The OBD II system also assists the
service technician in properly servicing your vehicle.
Thecheck engineindicator light illuminates when the ignition is first
turned to the ON position to check the bulb. If it comes on after the
VEHICLE
SETTINGDRIVER
SETTINGTRIP
ODO RANGE
RESET
N
S W
E
FUELECONOMY
DATE
TIMESYSTEM
CHECK
CHECK
ENGINEO/D
OFFANTI
THEFTT/C
OFF
CHECK
ENGINE
Instrumentation
9

engine is started, one of the engine's emission control systems may be
malfunctioning. The light may illuminate without a driveability concern
being noted. The vehicle will usually be drivable and will not require
towing.
What you should do if the check engine light illuminates
Light turns on solid:
This means that the OBD II system has detected a malfunction. Have
your vehicle serviced at your first opportunity.
Temporary malfunctions may also cause yourcheck enginelight to
illuminate. Examples follow:
²The vehicle has run out of fuel. (The engine may misfire or run
poorly.)
²Poor fuel quality or water in the fuel.
²The fuel cap may not have been securely tightened.
These temporary malfunctions can be corrected by filling the fuel tank
with good quality fuel and/or properly tightening the gas cap. After three
drive cycles without these or any other temporary malfunctions present,
thecheck enginelight should turn off.Novehicle service is required.
Light is blinking:
Engine misfire is occurring which could damage your catalytic converter.
You should drive in a moderate fashion (avoid heavy acceleration and
deceleration) and have your vehicle serviced at the first available
opportunity.
Under engine misfire conditions, excessive exhaust temperatures
could damage the catalytic converter, the fuel system, interior
floor coverings or other vehicle components, possibly causing a fire.
Air bag readiness
Briefly illuminates when the ignition
is turned on. If the light fails to
illuminate, continues to flash or
remains on, have the system
serviced immediately.
Instrumentation
10

O/D off
This light momentarily illuminates
when the ignition is turned to ON. It
also illuminates when the
transmission control switch been
pushed. When the light is on, the
transmission does not shift into
overdrive. If the light does not come
on when the transmission control switch is depressed or if the light
flashes when you are driving, have your vehicle serviced.
Anti-theft system
This light indicates the anti-theft
alarm system is armed. Refer to the
Controls and featureschapter.
Traction ControlYoff light
This light tells you that the Traction
Controlysystem has been turned
off using the Vehicle Settings menu
in the Message Center. The Traction
Controlysystem defaults to ªONº
(light is not illuminated) whenever
the vehicle is shut off and restarted.
This light will also illuminate if there is a total Traction Controlysystem
shut down.
If this lamp continuously stays on, contact your dealer for service as
soon as safely possible.
Headlamps on warning chime
Sounds when the headlamps or parking lamps are on, the ignition is off
(and the key is not in the ignition) and either front door is opened.
Safety belt warning chime
Chimes to remind you to fasten your safety belts.
For information on the safety belt warning chime, refer to theSeating
and safety restraintschapter.
O/ D
OFF
ANTI
THEFT
T/ C
OFF
Instrumentation
11

Supplemental restraint system (SRS) warning chime
For information on the SRS warning chime, refer to theSeating and
safety restraintschapter.
Key-in-ignition warning chime
Sounds when the key is left in the ignition in the OFF/LOCK or ACC
position and the driver's door is opened.
GAUGES
Engine coolant temperature gauge
Indicates the temperature of the
engine coolant. At normal operating
temperature, the needle remains
within the normal area (the area
between the ªHº and ªCº). If it
enters the red section, the engine is
overheating. Stop the vehicle as
soon as safely possible, switch off
the engine immediately and let the
engine cool. Refer toEngine
coolantin theMaintenance and
carechapter.
P
5
0 123
4
6
7
RPMx1000
H
C20406080
100
120
1404080120
200160
MPHkm/hFUEL
FILL DOOR
F
PREMIUM FUEL
RECOMMENDED
E
BRAKE000000.00
R
N
D
2
1
ABSCRUISE
ON
H
C
Instrumentation
12