1998 JAGUAR X308 rear bumper

            501‐17:  Roof  Open
ing
 Panel  
                 Description  and  Operation  
                     Roof Opening  Panel  
                 General Procedures  
                     Motor Synchronization  (76.82.48)  
                     Roof Opening  Panel  Alignment  
                 Removal and  Installation  
                     Roof Opening  Panel  (76.82.05)  
                     Roof Opening  Panel  Frame  (76.82.01)  
                     Roof Opening  Panel  Module  (86.76.07)  
                     Roof Opening  Panel  Motor  (86.76.01)  
                     Roof Opening  Panel Shie
ld (76.82.06)  
                     Roof Opening  Panel  Trim  
                     Roof Opening  Panel  Weatherstrip  (76.82.15)  
 
             501‐19:  Bumpers  
                 Specification  
                 Description  and  Operation  
                     Bumpers 
                 Removal and  Installation  
                     Front Bumper  (76.22.08)  
                     Front Bumper  and  Bumper  Cover  (76.22.08)  
                     Front Bumper  Cover  (76.22.78)  
                     Front Bumper  Isolator  (76.22.31)  
                     Rear Bumper  (76.22.27)  (76.22.52)  
                     Rear Bumper  Co
ver  (76.22.74)  (76.22.77)  
                     Rear Bumper  Isolator  (76.22.70)  
 
             501‐20A : Safety  Belt  System  
                 Specification  
                 Description  and  Operation  
                     Safety Belt  System  
                 Removal and  Installation  
                     Front Safety  Belt  Retractor  (76.73.10)  
                     Rear Safety  Belt  Retractor  (76.73.18)  
                     Safety Belt  Shoulder  Height  Adjuster  (76.73.12)  
  

P
arts List
The front towing point:
Is a welded loop on the ri
ght-ha
nd bumper mounting bracket.
Mus
t only be used when the grille
vane has been removed by turning the three fasteners anti-clockwise.
Rear Towing Point

The rear towing point is a welded loop on the right-hand side of the trunk floor panel; it must not be used for towing
another vehicle.

It
em
Par
t Number
De
scription
1—Fr

ont towing loop
2—Gr

ille vane
3—Gr

ille vane fastener


F
ront Towing Point

Front Suspension - Fro
nt Stabilizer Bar
Re
moval and Installation
Materials
S
pecification
Cas

trol NTR
Remov

al
Na
me
R

ubber Suspension Insulator Lube
1. Raise front of vehicle and support on stands. Refer to Section
100-02.

2. R
emove generator front cooling duct.
Re

move bolt.
Move duct rea

rwards to rele
ase tang from undertray.
R
elease front duct from rear vertical duct.

3. R
emove scrivets or screws se
curing undertray to bumper
cover. Discard scrivets.

4. R
emove and discard tiestrap securing undertray to crossbeam
brace.
5. At each side of vehicle, remo ve and discard scrivet securing
undertray to wheelarch liner.

Front Suspension - Front Stabilizer B
ar Bushing
Re
mo
val and Installation
Materials
S p
ecification
Cas
t
rol NTR
Remov
a
l
Na
m
e
R
u
bber Suspension Insulator Lube
1. Raise front of vehicle and support on stands. Refer to Section
100-02.

2. Re
move generator front cooling duct.
Re
mo
ve bolt.
Move duct rea
r
wards to rele
ase tang from undertray.
Re
lease front duct from rear vertical duct.

3. Re
move scrivets or screws se
curing undertray to bumper
cover. Discard scrivets.

4. Re
move and discard tiestrap securing undertray to crossbeam
front brace.
5. At each side of vehicle, remo ve and discard scrivet securing
undertray to wheelarch liner.

7. Using screws or new scrivets , secure undertray
to front
bumper cover.

8. Usi
ng a new tiestrap, secure undertray to crossbeam front
brace.

9. Usi
ng new scrivets, secure un
dertray to each wheelarch
liner.
10. Install generator cool ing duct deflector.
Po
sition deflector over
rear vertical duct.
Sl
ide deflector forward to
engage center tang over
undertray.

Rear Muffler Assembly

The left-hand and right-hand rear muffler assemblies comprise:
Absorption type muffler. Inlet pipe and tailpipe welded to the muffler. Tailpipe bright finisher integral with the tailpipe.
Tailpipe Clearance to Moulded Bumper

The functi
on of the parking aid is to prov
ide an audible warning to the driver of the distance to obstacles near the rear
bumper of the vehicle when parking or travelling at a slow sp eed. The system provides an assistance to the driver when
parking in order to help avoid collision with obstacles.
The sensor range at the rear of the vehicl e should be 1.8 meters. This should extend the full width of the rear bumper and
reduce to 50 cm at the vehicle co rners. The vertical range is adequate to protec t the highest and lowest points of the rear of
the vehicle. The system will detect curbs with heights of at least 18 cm. Obstacles, such as curbs, that are low enough to
pass under the vehicle until they make contact with the tires will not be detected.
The system activates a specific speaker with a tone signifying the distance to the obstacle. The tone consists of a beep and
defined space ratio which varies depending on the calculated distance. When the distance to the obstacle is less than 20 cm
the speaker tone is continuous.
The parking aid is continuously in operation, unless towing wh en the system automatically switches off. If the reverse aid
develops a fault the tone will sound continuously for three seconds when the igni tion is switched on or the reverse gear is
selected.
The parking aid system comprises of:
a
module mounted in the batte
ry junction box (BJB).
fou
r rear bumper mounted sensors which have a 90° angled electrical connector.
an audible speaker, moun

ted on
the rear parcel shelf.


It
em
Par
t Number
De
scription
1—Parkin

g aid module
2—Rear

parking aid speaker
3—Rear

parking aid sensors

Direction indicator and side marker lamps
Each front direction indicator and side marker lamp is retained in the bumper cover by a lug at one end and a spring clip at
the other end. The side marker lamps are not electrically connected for certain markets.
The side repeater lamps are secured by sp ring clips on the lower edge of the lamp unit. In certain markets Jaguar leaper
badges are substituted for side repeater lamps.
Fog lamps
The fog lamps are located in recesses in the front bump er and secured by three screws. The la mps which are not
interchangeable left to right, are accessed from the rear of the bumper.
Operation
All lamps are controlled by the BPM which provides an appropriate output in response to an input received when a selected
switch is operated.
All lamps receive an input direct from th e BPM with the exception of the main be am, dip beam and front fog lamps which
receive an input from the BPM vi a the respective relays and fuses; refer to section 418-01.
Fault analysis must be undertaken using the PDU. Refer to Diagnosis and Testing.
Consult the relevant Electrical Guid e for details of circuit operation.
Rear Lamps

ItemPart NumberDescription
1—License Plate Lamps