1998 JAGUAR X308 Ground

Seating - Rear Seat Track
Removal and Installation
Removal
1. Remove battery cover and disc onnect ground cable from
battery terminal. Refer to 86.15.19.

2. Slacken and remove the two seat cushion front securing bolts
and nuts.

3. Move the seat cushion forward to release it from the two frame
rear tangs.

4. Disconnect the cushion heater harness multiplug and remove
cushion from seat frame.

5. Remove and discard pl astic scrivet securing lower end of side
trim to inner wheela rch stud and withdraw trim from stud.

11.
Fit and tighten cushion front securing bolts and nuts.
12. Connect ground cable to batt ery terminal and fit battery
cover. Refer to 86.15.15.
13. Return seat to original position.

Seating - Seat Control Switch
Removal and Installation
Removal
1. Remove battery cover and disc onnect ground cable from
battery terminal. Refer to 86.15.19.
2. Remove front seat for ac cess. Refer to 76.70.01.
3. Place seat inverted on clean working surface for access to
underside.

4. Release cushion cover retaining strip from edge of seat frame.

5. Release cushion cover front elastic retaining straps from seat
frame.

6. Position cushion cover sides for access to cushion pad, raise
pad to access back of swit chpack and disconnect harness
multiplug.
7. Release switchpack upper retaining tangs, and lower retaining
tangs situated by seat sliders and remove switchpack from
seat.

Installation



1. Install and fully seat switchpack in seat mounting.
2. Raise cushion pad for access to rear of switchpack and connect
harness multiplug.
3. Release cushion pad and secure cushion cover front elastic
retaining straps to seat frame.
4. Pull cushion cover over cushion pad and fully seat edge
retaining strip on seat frame.
5. Install seat in vehicle. Refer to 76.70.01.
6. Connect ground cable to battery terminal and fit battery cover.
Refer to 86.15.15.

Glass, Frames and Mechanisms - Front Door Window Glass
Removal and Installation
Removal
Installation
1. Remove battery cover and disc onnect ground cable from
battery terminal. Refer to 86.15.19.
2. Remove front door casing. Refer to 76.34.01.
3. Remove water shedder carefu lly guiding harness through
penetration, and place adhesive face down on clean polythene
sheet.
4. Position PVC weathe rshield for access.
5. Remove front door modu le. Refer to 86.80.34.
6. Remove front door glass lift motor and regulator assembly.
Refer to 86.25.04.
7. Supporting glass, remove tape securing it to top of door for
motor removal.

8. Withdraw glass upwards through aperture and out via outboard side of frame.
1. Position glass in frame aperture.

2. Locate leading edge of glass in seal of front channel.

3. Carefully slide glass into position, ensuring that seals are not
deformed into channels.

4.
Fully raise glass and using linen tape, secure to top of door
frame.
5. Fit door glass lift motor. Refer to 86.25.04.
6. Fit door module. Refer to 86.80.34.
7. Reposition PVC inne r weathershield.
8. Position water shedder and carefully pass harness multiplugs
through penetration.
9. Ensuring door mating surfaces ar e clean and dry, firmly seat
water shedder.
10. Fit door casing. Refer to 76.34.01.
11. Connect ground cable to batter y terminal and fit cover to
battery. Refer to 86.15.15.

Glass, Frames and Mechanisms - Front Door Window Regulator and Motor
Removal and Installation
Removal
1. Ensure that door glass is in fully up position.
2. Remove battery cover and disc onnect ground cable from
battery terminal. Refer to 86.15.19.
3. Remove casing/armrest asse mbly from door. Refer to
76.34.01.
4. Remove water shedder carefu lly guiding harness through
penetration, and place adhesive face down on clean polythene
sheet.
5. Position PVC inner weat hershield for access.
6. Remove front door modu le. Refer to 86.80.34.
7. Using linen tape, secure to p of glass to door frame.

8. Disconnect harness mult iplug from lift motor.

9. Slacken and remove screws and nuts securing lift motor to
door.

10. Mark position of door glass gu ide securing screws and slacken and remove screws.
11. Separate motor/regulator assembly from glass, lower into
bottom of door and remove assembly from door.

supply from motor multiplug.

15.
Adjust regulator up stop.
Slacken stop securing bolt.
Move stop rearwards to abut regulator quadrant.
Tighten stop securing bolt.
16. Reconnect harness multiplug to lift motor.
17. Fit door module. Refer to 86.80.34.
18. Reposition PVC weathershield.
19. Position water shedder and carefully pass harness multiplugs
through penetration.
20. Ensuring door mating surfaces ar e clean and dry, firmly seat
water shedder.
21. Fit casing/armrest assembly to door. Refer to 76.34.01.
22. Connect ground cable to batter y terminal and fit cover to
battery. Refer to 86.15.15.