1998 DODGE RAM 1500 flat tire

STUDS
REMOVAL
(1) Raise and support the vehicle.
(2) Remove the wheel and tire assembly.
(3) Remove the brake caliper, caliper adapter and
rotor, (Refer to 5 - BRAKES/HYDRAULIC/MECHAN-
ICAL/ROTORS - REMOVAL).
(4) Remove the stud from the hub with Remover
C-4150A (Fig. 25).
INSTALLATION
(1) Install the new stud into the hub flange.
(2) Install the three washers onto the stud, then
install the lug nut with the flat side of the nut
against the washers.
(3) Tighten the lug nut until the stud is pulled
into the hub flange. Verify that the stud is properly
seated into the flange.
(4) Remove the lug nut and washers.
(5) Install the brake rotor, caliper adapter, and cal-
iper, (Refer to 5 - BRAKES/HYDRAULIC/MECHAN-
ICAL/ROTORS - INSTALLATION).
(6) Install the wheel and tire assembly, (Refer to
22 - TIRES/WHEELS/WHEELS - STANDARD PRO-
CEDURE), use new the lug nut on stud or studs that
were replaced.
(7) Remove the support and lower vehicle.
WHEEL COVER
REMOVAL
NOTE: The hub caps must be removed before rais-
ing the vehicle off the ground.NOTE: You must use the flat end of the hub/cap
remover/installer combination tool to pry off the
wheel skins. Insert the flat tip completely and using
a back and forth motion, loosen the wheel skin.
repeat this procedure around the tire until the wheel
skin pops off.
(1) On 2500/3500 single rear wheel (SRW) models,
insert a hub/cap remover/installer combination tool
using the blade on the end of the tool to pry the cap
off in a back and forth motion.
(2) On 3500 models with dual rear wheels (DRW),
you must first remove the hub caps. The hub/cap
remover/installer combination tool must be inserted
in the pry off notch of the rear hub caps.
(3) Position the hub/cap remover/installer combina-
tion tool and pull out on the tool firmly. The cap
should come off.
(4) The wheel skins can now be removed from the
wheel.
(5) On 3500 models front hub caps use the hub/cap
remover/installer combination tool to pry off the cap
in a back and forth motion. The wheel skins can now
be removed.
INSTALLATION
INSTALLATION - REAR
(1) Install one 1 1/2 in. valve stem extension on
each rear inner wheel.
NOTE: A 3/8 in. drive 10mm deep wheel socket with
a 10 in. or greater extension can be used to remove
the existing valve stem cap and install the exten-
sion.
(2) Install one 1 in. valve stem extension on each
outer wheel.
(3) Align the cooling windows of the wheel skin
with the cooling windows of the wheel. Seat one side
of the wheel skin's retainer onto the wheel. Using a
rubber mallet, strike thew wheel skin on the outer
circumference. Strike at several locations around the
circumference until the skin is fully seated.
NOTE: The wheel skin and the hub cap are fully
seated when there is a consistent gap between the
skin/cap and the wheel.
(4) Tug on the hub/cap wheel skin to ensure that
they are properly installed.
INSTALLATION - FRONT
(1) Align the valve stem with the notch in the
wheel skin.
Fig. 25 Wheel Stud Removal
1 - REMOVER
2 - WHEEL STUD
22 - 14 TIRES/WHEELSDR

IGNITION CIRCUIT SENSE -
DESCRIPTION.......................8E-10
IGNITION CIRCUIT SENSE - OPERATION . . 8E-11
IGNITION COIL - DESCRIPTION..........8I-11
IGNITION COIL - INSTALLATION.........8I-14
IGNITION COIL - OPERATION............8I-12
IGNITION COIL - REMOVAL.............8I-13
IGNITION COIL CAPACITOR -
DESCRIPTION........................8I-21
IGNITION COIL CAPACITOR -
INSTALLATION.......................8I-21
IGNITION COIL CAPACITOR - OPERATION . . 8I-21
IGNITION COIL CAPACITOR - REMOVAL . . . 8I-21
IGNITION COIL RESISTANCE, 3.7L V-6.....8I-5
IGNITION COIL RESISTANCE, 4.7L V-8.....8I-5
IGNITION COIL RESISTANCE, 5.7L V-8.....8I-5
IGNITION CONTROL - DESCRIPTION.......8I-1
IGNITION SWITCH - DESCRIPTION........19-9
IGNITION SWITCH - DESCRIPTION,
KEY-IN.............................19-11
IGNITION SWITCH - DIAGNOSIS AND
TESTING............................19-9
IGNITION SWITCH - INSTALLATION......19-11
IGNITION SWITCH - OPERATION.........19-9
IGNITION SWITCH - REMOVAL..........19-10
IGNITION SWITCH AND KEY LOCK
CYLINDER - DIAGNOSIS AND TESTING . . . 19-11
IGNITION TIMING, SPECIFICATIONS.......8I-5
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE........................8F-11
IMMOBILIZER MODULE - DESCRIPTION,
SENTRY KEY........................8E-13
IMMOBILIZER MODULE - INSTALLATION,
SENTRY KEY........................8E-15
IMMOBILIZER MODULE - OPERATION,
SENTRY KEY........................8E-13
IMMOBILIZER MODULE - REMOVAL,
SENTRY KEY........................8E-15
IMMOBILIZER MODULE (SKIM) -
DESCRIPTION, SENTRY KEY.............8Q-1
IMMOBILIZER MODULE (SKIM) -
OPERATION, SENTRY KEY..............8Q-2
IMMOBILIZER SYSTEM INDICATOR
LAMP - DESCRIPTION, SENTRY KEY......8Q-5
IMMOBILIZER SYSTEM INDICATOR
LAMP - OPERATION, SENTRY KEY........8Q-5
IMMOBILIZER SYSTEM INITIALIZATION,
STANDARD PROCEDURE - SENTRY
KEY................................8Q-3
IMMOBILIZER SYSTEM (SKIS) -
DESCRIPTION, SENTRY KEY.............8Q-1
IMMOBILIZER SYSTEM (SKIS) -
OPERATION, SENTRY KEY..............8Q-2
IMMOBILIZER SYSTEM TRANSPONDER
PROGRAMMING, STANDARD
PROCEDURE - SENTRY KEY.............8Q-4
IMPACT SENSOR - DESCRIPTION, SIDE . . 8O-59
IMPACT SENSOR - OPERATION, SIDE....8O-59
INCORRECT FLUID LEVEL - DIAGNOSIS
AND TESTING, EFFECTS OF......21-201,21-366
INDEPENDENT FRONT SUSPENSION -
DESCRIPTION, GEAR..................19-17
INDEPENDENT FRONT SUSPENSION -
INSTALLATION, GEAR.................19-18
INDEPENDENT FRONT SUSPENSION -
REMOVAL, GEAR.....................19-17
INDICATOR - DESCRIPTION, ABS........8J-17
INDICATOR - DESCRIPTION, AIRBAG.....8J-18
INDICATOR - DESCRIPTION, BRAKE/
PARK BRAKE........................8J-19
INDICATOR - DESCRIPTION, CARGO
LAMP
..............................8J-20
INDICATOR - DESCRIPTION, CHECK
GAUGES
............................8J-21
INDICATOR - DESCRIPTION, CRUISE
.....8J-22
INDICATOR - DESCRIPTION, DOOR AJAR
. . 8J-23
INDICATOR - DESCRIPTION, ETC
........8J-25
INDICATOR - DESCRIPTION, GEAR
SELECTOR
..........................8J-27
INDICATOR - DESCRIPTION, HIGH BEAM
. . 8J-28
INDICATOR - DESCRIPTION, LAMP OUT
. . . 8J-29
INDICATOR - DESCRIPTION, LOW FUEL
. . . 8J-30
INDICATOR - DESCRIPTION, SEATBELT
. . . 8J-34
INDICATOR - DESCRIPTION, SECURITY
. . . 8J-35
INDICATOR - DESCRIPTION, SERVICE
4WD
...............................8J-36
INDICATOR - DESCRIPTION, TOW/HAUL
. . . 8J-39INDICATOR - DESCRIPTION, TRANS
TEMP..............................8J-40
INDICATOR - DESCRIPTION, TURN
SIGNAL............................8J-40
INDICATOR - DESCRIPTION, UPSHIFT....8J-41
INDICATOR - DESCRIPTION, WAIT-TO-
START .............................8J-44
INDICATOR - DESCRIPTION, WASHER
FLUID..............................8J-44
INDICATOR - DESCRIPTION, WATER-IN-
FUEL..............................8J-45
INDICATOR - DIAGNOSIS AND TESTING,
BRAKE.............................8J-20
INDICATOR - OPERATION, ABS..........8J-17
INDICATOR - OPERATION, AIRBAG.......8J-18
INDICATOR - OPERATION, BRAKE/PARK
BRAKE.............................8J-19
INDICATOR - OPERATION, CARGO LAMP . . 8J-20
INDICATOR - OPERATION, CHECK
GAUGES............................8J-21
INDICATOR - OPERATION, CRUISE.......8J-22
INDICATOR - OPERATION, DOOR AJAR . . . 8J-23
INDICATOR - OPERATION, ETC..........8J-25
INDICATOR - OPERATION, GEAR
SELECTOR..........................8J-27
INDICATOR - OPERATION, HIGH BEAM....8J-28
INDICATOR - OPERATION, LAMP OUT....8J-29
INDICATOR - OPERATION, LOW FUEL.....8J-30
INDICATOR - OPERATION, SEATBELT.....8J-34
INDICATOR - OPERATION, SECURITY......8J-36
INDICATOR - OPERATION, SERVICE 4WD . . 8J-37
INDICATOR - OPERATION, TOW/HAUL....8J-39
INDICATOR - OPERATION, TRANS TEMP . . 8J-40
INDICATOR - OPERATION, TURN SIGNAL . . 8J-41
INDICATOR - OPERATION, UPSHIFT......8J-42
INDICATOR - OPERATION, WAIT-TO-
START .............................8J-44
INDICATOR - OPERATION, WASHER
FLUID..............................8J-44
INDICATOR - OPERATION, WATER-IN-
FUEL..............................8J-45
INDICATOR LAMP - DESCRIPTION,
SENTRY KEY IMMOBILIZER SYSTEM......8Q-5
INDICATOR LAMP - OPERATION,
SENTRY KEY IMMOBILIZER SYSTEM......8Q-5
INDICATOR LAMP (MIL) - DESCRIPTION,
MALFUNCTION.......................8J-31
INDICATOR LAMP (MIL) - OPERATION,
MALFUNCTION.......................8J-31
INDICATOR TEST - STANDARD
PROCEDURE, BUILT-IN................8F-10
INDICATORS - DIAGNOSIS AND
TESTING, TREAD WEAR................22-8
INERTIA HINGE COVER - INSTALLATION,
CENTER SEAT BACK..................23-77
INERTIA HINGE COVER - REMOVAL,
CENTER SEAT BACK..................23-77
INFLATION PRESSURES - DESCRIPTION,
TIRE................................22-7
INFO CENTER - DESCRIPTION,
ELECTRONIC VEHICLE.................8M-7
INFO CENTER - INSTALLATION,
ELECTRONIC VEHICLE.................8M-9
INFO CENTER - OPERATION,
ELECTRONIC VEHICLE.................8M-7
INFO CENTER - REMOVAL, ELECTRONIC
VEHICLE............................8M-9
INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING
PUMP.............................19-40
INITIALIZATION, STANDARD PROCEDURE
- SENTRY KEY IMMOBILIZER SYSTEM....8Q-3
INJECTED RINGS - ASSEMBLY, WITH......3-13
INJECTED RINGS - DISASSEMBLY, WITH . . . 3-11
INJECTION PUMP - DESCRIPTION, FUEL . . 14-53
INJECTION PUMP - INSTALLATION, FUEL . 14-55
INJECTION PUMP - OPERATION, FUEL....14-53
INJECTION PUMP - REMOVAL, FUEL.....14-54
INJECTION PUMP TIMING - DIAGNOSIS
AND TESTING, FUEL..................14-53
INJECTOR - DESCRIPTION, FUEL . . . 14-26,14-74
INJECTOR - INSTALLATION, FUEL........14-77
INJECTOR - OPERATION, FUEL
.....14-26,14-74
INJECTOR - REMOVAL, FUEL
...........14-75
INJECTOR FIRING ORDER, DIESEL -
FUEL
..............................14-48
INJECTOR RAIL - DESCRIPTION, FUEL
....14-78
INJECTOR RAIL - INSTALLATION, FUEL
. . . 14-78INJECTOR RAIL - OPERATION, FUEL.....14-78
INJECTOR RAIL - REMOVAL, FUEL.......14-78
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - DESCRIPTION.....14-79
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - INSTALLATION.....14-79
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - OPERATION.......14-79
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - REMOVAL........14-79
INLET FILTER - INSTALLATION..........14-20
INLET FILTER - REMOVAL..............14-20
INLET HOSE - INSTALLATION, HEATER....24-64
INLET HOSE - REMOVAL, HEATER.......24-64
INNER BELT MOLDING - INSTALLATION,
FRONT DOOR.......................23-93
INNER BELT MOLDING - INSTALLATION,
REAR DOOR........................23-94
INNER BELT MOLDING - REMOVAL,
FRONT DOOR.......................23-93
INNER BELT MOLDING - REMOVAL,
REAR DOOR........................23-94
INPUT - OPERATION, ASD SENSE - PCM . . . 8I-5
INPUT CLUTCH ASSEMBLY - ASSEMBLY . 21-378
INPUT CLUTCH ASSEMBLY -
DESCRIPTION......................21-373
INPUT CLUTCH ASSEMBLY -
DISASSEMBLY......................21-374
INPUT CLUTCH ASSEMBLY - OPERATION . 21-373
INPUT SHAFT SEAL - INSTALLATION,
STEERING GEAR.......................19-29
INPUT SHAFT SEAL - REMOVAL,
STEERING GEAR.....................19-27
INPUT SPEED SENSOR - DESCRIPTION . . 21-382
INPUT SPEED SENSOR - INSTALLATION . 21-382
INPUT SPEED SENSOR - OPERATION....21-382
INPUT SPEED SENSOR - REMOVAL.....21-382
INSERTS - INSTALLATION, SPRING TIP....2-45
INSERTS - REMOVAL, SPRING TIP........2-44
INSIDE HANDLE ACTUATOR -
INSTALLATION..................23-22,23-32
INSIDE HANDLE ACTUATOR - REMOVAL . . 23-22,
23-31
INSTRUMENT CLUSTER - ASSEMBLY.....8J-15
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING.......................8J-10
INSTRUMENT CLUSTER - DISASSEMBLY . . 8J-14
INSTRUMENT CLUSTER - INSTALLATION . . 8J-16
INSTRUMENT CLUSTER - OPERATION.....8J-6
INSTRUMENT CLUSTER - REMOVAL.....8J-14
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-7
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-7
INSTRUMENT PANEL ASSEMBLY -
INSTALLATION.......................23-55
INSTRUMENT PANEL ASSEMBLY -
REMOVAL..........................23-52
INSTRUMENT PANEL CENTER BEZEL -
INSTALLATION.......................23-57
INSTRUMENT PANEL CENTER BEZEL -
REMOVAL..........................23-57
INSTRUMENT PANEL DEMISTER DUCTS
- INSTALLATION.....................24-37
INSTRUMENT PANEL DEMISTER DUCTS
- REMOVAL.........................24-36
INSTRUMENT PANEL DRIVER SIDE
BEZEL - INSTALLATION................23-58
INSTRUMENT PANEL DRIVER SIDE
BEZEL - REMOVAL...................23-58
INSTRUMENT PANEL DUCTS -
INSTALLATION.......................24-37
INSTRUMENT PANEL DUCTS - REMOVAL . 24-37
INSTRUMENT PANEL HEADLAMP
SWITCH BEZEL - INSTALLATION.........23-56
INSTRUMENT PANEL HEADLAMP
SWITCH BEZEL - REMOVAL............23-56
INSTRUMENT PANEL LOWER
SURROUND - INSTALLATION...........23-59
INSTRUMENT PANEL LOWER
SURROUND - REMOVAL
...............23-59
INSTRUMENT PANEL TOP COVER -
INSTALLATION
.......................23-59
INSTRUMENT PANEL TOP COVER -
REMOVAL
..........................23-58
INTAKE AIR HEATER - DESCRIPTION
.....14-80
INTAKE AIR HEATER - INSTALLATION
.....14-80
DRINDEX 17
Description Group-Page Description Group-Page Description Group-Page

PRESSURE HOSE - REMOVAL.....19-44,19-45
PRESSURE LEAKAGE - DIAGNOSIS AND
TESTING, CYLINDER COMBUSTION . . . 9-186,9-8,
9-93
PRESSURE LIMITING VALVE -
DESCRIPTION, FUEL..................14-61
PRESSURE LIMITING VALVE -
INSTALLATION, FUEL.................14-61
PRESSURE LIMITING VALVE -
OPERATION, FUEL....................14-61
PRESSURE LIMITING VALVE - REMOVAL,
FUEL..............................14-61
PRESSURE (LP) SENSOR -
DESCRIPTION, LINE.................21-382
PRESSURE (LP) SENSOR -
INSTALLATION, LINE.................21-383
PRESSURE (LP) SENSOR - OPERATION,
LINE..............................21-383
PRESSURE (LP) SENSOR - REMOVAL,
LINE..............................21-383
PRESSURE RELEASE - STANDARD
PROCEDURE, FUEL SYSTEM.............14-2
PRESSURE RELIEF VALVE - CLEANING,
OIL................................9-294
PRESSURE RELIEF VALVE -
DESCRIPTION, HIGH..................24-48
PRESSURE RELIEF VALVE - INSPECTION,
OIL................................9-294
PRESSURE RELIEF VALVE -
INSTALLATION, OIL...................9-294
PRESSURE RELIEF VALVE - OPERATION,
HIGH..............................24-48
PRESSURE RELIEF VALVE - REMOVAL,
OIL.................................9-294
PRESSURE SENSOR - DESCRIPTION,
FUEL..............................14-60
PRESSURE SENSOR - INSTALLATION,
FUEL..............................14-61
PRESSURE SENSOR - OPERATION, FUEL . . 14-60
PRESSURE SENSOR - REMOVAL, FUEL . . . 14-60
PRESSURE SENSOR/SWITCH -
DESCRIPTION, OIL....................9-67
PRESSURE SENSOR/SWITCH -
INSTALLATION, OIL....................9-67
PRESSURE SENSOR/SWITCH -
OPERATION, OIL......................9-67
PRESSURE SENSOR/SWITCH -
REMOVAL, OIL.......................9-67
PRESSURE, SPECIFICATIONS - FUEL
SYSTEM............................14-3
PRESSURE SWITCH - DESCRIPTION,
POWER STEERING...................19-46
PRESSURE SWITCH - INSTALLATION,
OIL................................9-294
PRESSURE SWITCH - OPERATION,
POWER STEERING...................19-46
PRESSURE SWITCH - REMOVAL, OIL.....9-294
PRESSURE TEST - DIAGNOSIS AND
TESTING, HYDRAULIC..........21-141,21-316
PRESSURE TRANSDUCER -
DESCRIPTION, A/C
...................24-15
PRESSURE TRANSDUCER - DIAGNOSIS
AND TESTING, A/C
...................24-16
PRESSURE TRANSDUCER -
INSTALLATION, A/C
...................24-16
PRESSURE TRANSDUCER - OPERATION,
A/C
................................24-16
PRESSURE TRANSDUCER - REMOVAL,
A/C
................................24-16
PRESSURES - DESCRIPTION, TIRE
INFLATION
...........................22-7
PRIMING - STANDARD PROCEDURE,
FUEL SYSTEM
.......................14-47
PROCESS - SPECIFICATIONS, WELD
.....13-15
PROGRAMING - STANDARD
PROCEDURE, RKE TRANSMITTER
........8N-9
PROGRAMMING - STANDARD
PROCEDURE, ELECTRONIC VEHICLE
INFORMATION CENTER
................8M-8
PROGRAMMING - STANDARD
PROCEDURE, ENHANCED SEATBELT
REMINDER
..........................8J-35
PROGRAMMING - STANDARD
PROCEDURE, PCM/SKIM
...............8E-14
PROGRAMMING, STANDARD
PROCEDURE - SENTRY KEY
IMMOBILIZER SYSTEM TRANSPONDER
....8Q-4PROPELLER SHAFT - DIAGNOSIS AND
TESTING.............................3-1
PROPELLER SHAFT - HD FRONT -
INSTALLATION.........................3-7
PROPELLER SHAFT - HD FRONT -
REMOVAL............................3-7
PROPELLER SHAFT - INSTALLATION,
REAR................................3-8
PROPELLER SHAFT - REMOVAL, REAR.....3-8
PROPELLER SHAFT - SPECIAL TOOLS......3-6
PROPELLER SHAFT - SPECIFICATIONS......3-6
PROPELLER SHAFT - STANDARD
PROCEDURE..........................3-3
PROPELLER SHAFT- LD FRONT -
INSTALLATION.........................3-7
PROPELLER SHAFT- LD FRONT -
REMOVAL............................3-6
PROPORTIONING - DESCRIPTION,
ELECTRONIC VARIABLE BRAKE..........5-49
PROPORTIONING - OPERATION,
ELECTRONIC VARIABLE BRAKE..........5-49
PTO SWITCH - DESCRIPTION......14-36,14-85
PTO SWITCH - OPERATION........14-36,14-85
PULLEY - INSTALLATION..............19-47
PULLEY - REMOVAL..................19-47
PUMP - 5.7L - INSTALLATION, WATER.....7-63
PUMP - 5.7L - REMOVAL, WATER........7-63
PUMP - 5.9L DIESEL - CLEANING,
WATER .............................7-62
PUMP - 5.9L DIESEL - DESCRIPTION,
WATER...............................7-62
PUMP - 5.9L DIESEL - INSPECTION,
WATER .............................7-62
PUMP - 5.9L DIESEL - INSTALLATION,
WATER .............................7-62
PUMP - 5.9L DIESEL - OPERATION,
WATER .............................7-62
PUMP - 5.9L DIESEL - REMOVAL,
WATER .............................7-62
PUMP - 8.0L - CLEANING, WATER........7-66
PUMP - 8.0L - INSPECTION, WATER......7-66
PUMP - 8.0L - INSTALLATION, WATER.....7-66
PUMP - 8.0L - REMOVAL, WATER........7-64
PUMP - ASSEMBLY, OIL...........9-158,9-69
PUMP - ASSEMBLY, OIL........21-214,21-390
PUMP - CLEANING, OIL.....9-157,9-224,9-295
PUMP - CLEANING, OIL........21-214,21-390
PUMP - DESCRIPTION................19-39
PUMP - DESCRIPTION, FUEL...........14-11
PUMP - DESCRIPTION, FUEL INJECTION . . 14-53
PUMP - DESCRIPTION, FUEL TRANSFER . . 14-64
PUMP - DESCRIPTION, LEAK DETECTION . 25-13
PUMP - DESCRIPTION, OIL......21-213,21-386
PUMP - DESCRIPTION, WATER..........7-59
PUMP - DIAGNOSIS AND TESTING,
WATER .........................7-62,7-63
PUMP - DISASSEMBLY, OIL........9-157,9-68
PUMP - DISASSEMBLY, OIL.....21-214,21-388
PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER
STEERING..........................19-40
PUMP - INSPECTION, OIL . . . 9-157,9-224,9-295,
9-68
PUMP - INSPECTION, OIL.......21-214,21-390
PUMP - INSTALLATION, FUEL INJECTION . 14-55
PUMP - INSTALLATION, FUEL TRANSFER . 14-65
PUMP - INSTALLATION, LEAK
DETECTION.........................25-16
PUMP - INSTALLATION, OIL . 9-159,9-225,9-296,
9-69
PUMP - OPERATION..................19-40
PUMP - OPERATION, FUEL.............14-11
PUMP - OPERATION, FUEL INJECTION....14-53
PUMP - OPERATION, FUEL TRANSFER....14-64
PUMP - OPERATION, LEAK DETECTION . . . 25-14
PUMP - OPERATION, OIL.......21-213,21-386
PUMP - OPERATION, WATER............7-60
PUMP - REMOVAL, FUEL INJECTION.....14-54
PUMP - REMOVAL, FUEL TRANSFER.....14-64
PUMP - REMOVAL, LEAK DETECTION....25-16
PUMP - REMOVAL, OIL . 9-156,9-224,9-294,9-67
PUMP BYPASS - DESCRIPTION, WATER
. . . 7-59
PUMP BYPASS - OPERATION, WATER
.....7-60
PUMP FRONT SEAL - INSTALLATION,
OIL
...............................21-391
PUMP FRONT SEAL - REMOVAL, OIL
....21-391
PUMP LEAKAGE - DIAGNOSIS AND
TESTING
...........................19-40PUMP MODULE - DESCRIPTION, FUEL....14-11
PUMP MODULE - INSTALLATION, FUEL . . . 14-12
PUMP MODULE - OPERATION, FUEL.....14-11
PUMP MODULE - REMOVAL, FUEL.......14-12
PUMP RELAY - DESCRIPTION, FUEL.....14-27
PUMP RELAY - INSTALLATION, FUEL.....14-28
PUMP RELAY - OPERATION, FUEL.......14-27
PUMP RELAY - REMOVAL, FUEL........14-28
PUMP RELAYS - DIAGNOSIS AND
TESTING, ASD AND FUEL...............8I-5
PUMP TIMING - DIAGNOSIS AND
TESTING, FUEL INJECTION.............14-53
PUMP VOLUME CHECK - STANDARD
PROCEDURE, OIL...................21-387
PUMP/MOTOR - DESCRIPTION, WASHER . 8R-13
PUMP/MOTOR - INSTALLATION,
WASHER...........................8R-14
PUMP/MOTOR - OPERATION, WASHER . . . 8R-13
PUMP/MOTOR - REMOVAL, WASHER....8R-14
PUSHRODS - CLEANING...............9-252
PUSHRODS - INSPECTION.............9-253
QUAD CAB - INSTALLATION.......8O-36,8O-61
QUAD CAB - REMOVAL..........8O-33,8O-60
QUICK CONNECT FITTING -
DESCRIPTION........................14-8
QUICK LEARN - STANDARD
PROCEDURE, TCM...................8E-23
QUICK-CONNECT FITTINGS - STANDARD
PROCEDURE...........................14-8
RADIAL - PLY TIRES - DESCRIPTION......22-6
RADIATOR - 5.9L DIESEL - CLEANING.....7-56
RADIATOR - 5.9L DIESEL -
DESCRIPTION........................7-56
RADIATOR - 5.9L DIESEL - INSPECTION . . . 7-56
RADIATOR - 5.9L DIESEL -
INSTALLATION........................7-57
RADIATOR - 5.9L DIESEL - OPERATION....7-56
RADIATOR - 5.9L DIESEL - REMOVAL.....7-56
RADIATOR CAP - DIAGNOSIS AND
TESTING............................7-58
RADIATOR CAP-TO-FILLER NECK SEAL -
DIAGNOSIS AND TESTING..............7-58
RADIATOR COOLANT FLOW -
DIAGNOSIS AND TESTING..........7-54,7-56
RADIATOR CROSSMEMBER -
INSTALLATION, UPPER................23-42
RADIATOR CROSSMEMBER - REMOVAL,
UPPER.............................23-42
RADIATOR FAN - 5.9L DIESEL -
CLEANING...........................7-35
RADIATOR FAN - 5.9L DIESEL -
INSPECTION.........................7-35
RADIATOR FAN - 5.9L DIESEL -
INSTALLATION........................7-36
RADIATOR FAN - 5.9L DIESEL -
REMOVAL...........................7-35
RADIATOR FAN - GAS ENGINES -
CLEANING...........................7-34
RADIATOR FAN - GAS ENGINES -
INSPECTION.........................7-34
RADIATOR FAN - GAS ENGINES -
INSTALLATION........................7-34
RADIATOR FAN - GAS ENGINES -
REMOVAL...........................7-33
RADIATOR PRESSURE CAP -
DESCRIPTION........................7-57
RADIATOR PRESSURE CAP - OPERATION . . 7-58
RADIATOR-3.7L/4.7L/5.7L - CLEANING.....7-55
RADIATOR-3.7L/4.7L/5.7L -
DESCRIPTION........................7-54
RADIATOR-3.7L/4.7L/5.7L - INSPECTION . . . 7-55
RADIATOR-3.7L/4.7L/5.7L -
INSTALLATION........................7-55
RADIATOR-3.7L/4.7L/5.7L - OPERATION....7-54
RADIATOR-3.7L/4.7L/5.7L - REMOVAL.....7-54
RADIO - DESCRIPTION.................8A-8
RADIO - INSTALLATION................8A-8
RADIO - OPERATION...................8A-8
RADIO - REMOVAL....................8A-8
RADIO NOISE SUPPRESSION GROUND
STRAP - DESCRIPTION
.................8A-9
RADIO NOISE SUPPRESSION GROUND
STRAP - INSTALLATION
...............8A-10
RADIO NOISE SUPPRESSION GROUND
STRAP - OPERATION
..................8A-9
RADIO NOISE SUPPRESSION GROUND
STRAP - REMOVAL
....................8A-9
RAIL - DESCRIPTION, FUEL
............14-12
DRINDEX 25
Description Group-Page Description Group-Page Description Group-Page

TEMPERATURE SENSOR -
INSTALLATION, EVAPORATOR...........24-22
TEMPERATURE SENSOR -
INSTALLATION, INTAKE AIR............14-31
TEMPERATURE SENSOR - OPERATION,
BATTERY...........................8F-21
TEMPERATURE SENSOR - OPERATION,
ENGINE COOLANT.....................7-38
TEMPERATURE SENSOR - OPERATION,
EVAPORATOR.......................24-22
TEMPERATURE SENSOR - OPERATION,
INTAKE AIR .........................14-30
TEMPERATURE SENSOR - OPERATION,
TRANSMISSION...............21-267,21-408
TEMPERATURE SENSOR - REMOVAL,
BATTERY...........................8F-21
TEMPERATURE SENSOR - REMOVAL,
ENGINE COOLANT.....................7-39
TEMPERATURE SENSOR - REMOVAL,
EVAPORATOR.......................24-22
TEMPERATURE SENSOR - REMOVAL,
INTAKE AIR .........................14-30
TEMPERATURE SENSOR CIRCUIT -
DIAGNOSIS AND TESTING, AMBIENT....8M-10
TEMPERATURE SENSOR/MAP SENSOR -
DESCRIPTION, INTAKE AIR.............14-82
TEMPERATURE SENSOR/MAP SENSOR -
INSTALLATION, INTAKE AIR............14-82
TEMPERATURE SENSOR/MAP SENSOR -
OPERATION, INTAKE AIR...............14-82
TEMPERATURE SENSOR/MAP SENSOR -
REMOVAL, INTAKE AIR................14-82
TEMPERATURE SENSOR/PRESSURE
SENSOR - DESCRIPTION, INLET AIR.......14-79
TEMPERATURE SENSOR/PRESSURE
SENSOR - INSTALLATION, INLET AIR.....14-79
TEMPERATURE SENSOR/PRESSURE
SENSOR - OPERATION, INLET AIR.......14-79
TEMPERATURE SENSOR/PRESSURE
SENSOR - REMOVAL, INLET AIR........14-79
TEMPORARY - DESCRIPTION, SPARE
TIRE................................22-6
TEMPORARY TIRE - DESCRIPTION,
SPARE .............................22-15
TENSION REDUCER - DESCRIPTION,
SEAT BELT .........................8O-53
TENSION REDUCER - DIAGNOSIS AND
TESTING, SEAT BELT.................8O-54
TENSION REDUCER - OPERATION, SEAT
BELT ..............................8O-54
TENSIONER - 3.7L / 4.7L -
DESCRIPTION, BELT...................7-21
TENSIONER - 3.7L / 4.7L -
INSTALLATION, BELT...................7-22
TENSIONER - 3.7L / 4.7L - OPERATION,
BELT ...............................7-21
TENSIONER - 3.7L / 4.7L - REMOVAL,
BELT ...............................7-21
TENSIONER - 5.9L DIESEL -
DESCRIPTION, BELT...................7-23
TENSIONER - 5.9L DIESEL -
INSTALLATION, BELT...................7-24
TENSIONER - 5.9L DIESEL - OPERATION,
BELT ...............................7-23
TENSIONER - 5.9L DIESEL - REMOVAL,
BELT ...............................7-23
TENSIONER - DESCRIPTION, SEAT BELT . . 8O-52
TENSIONER - OPERATION, SEAT BELT....8O-53
TENSIONER-5.7L - DESCRIPTION, BELT
....7-22
TENSIONER-5.7L - INSTALLATION, BELT
. . . 7-23
TENSIONER-5.7L - OPERATION, BELT
......7-22
TENSIONER-5.7L - REMOVAL, BELT
.......7-22
TERMINAL - INSTALLATION
.........8W-01-14
TERMINAL - REMOVAL
.............8W-01-14
TERMINAL REPAIR - STANDARD
PROCEDURE, GRID LINE
...............8G-4
TEST - DIAGNOSIS AND TESTING,
HEATER PERFORMANCE
................24-6
TEST - DIAGNOSIS AND TESTING,
HYDRAULIC PRESSURE
........21-141,21-316
TEST - DIAGNOSIS AND TESTING, ROAD
. . . 8P-3
TEST - DIAGNOSIS AND TESTING,
VACUUM SUPPLY
.....................8P-2
TEST - STANDARD PROCEDURE,
BUILT-IN INDICATOR
..................8F-10
TEST - STANDARD PROCEDURE,
IGNITION-OFF DRAW
..................8F-11TEST - STANDARD PROCEDURE,
OPEN-CIRCUIT VOLTAGE...............8F-10
TEST - STANDARD PROCEDURE,
VERIFICATION........................8O-9
TEST MODE - DESCRIPTION, CIRCUIT
ACTUATION..........................25-1
TEST MODE - DESCRIPTION, STATE
DISPLAY............................25-1
TESTER - STANDARD PROCEDURE,
USING MICRO 420 BATTERY............8F-12
TESTS - DIAGNOSIS AND TESTING,
CYLINDER COMPRESSION/LEAKAGE.....9-239
THEFT SECURITY SYSTEM, DIAGNOSIS
AND TESTING - VEHICLE...............8Q-3
THEFT/SECURITY SYSTEM -
DESCRIPTION, VEHICLE................8Q-1
THEFT/SECURITY SYSTEM - OPERATION,
VEHICLE............................8Q-1
THERMOSTAT - 3.7L/4.7L -
DESCRIPTION, ENGINE COOLANT.........7-44
THERMOSTAT - 3.7L/4.7L -
INSTALLATION, ENGINE COOLANT........7-45
THERMOSTAT - 3.7L/4.7L - OPERATION,
ENGINE COOLANT.....................7-44
THERMOSTAT - 3.7L/4.7L - REMOVAL,
ENGINE COOLANT.....................7-45
THERMOSTAT - 5.9L DIESEL -
DESCRIPTION, ENGINE COOLANT.........7-46
THERMOSTAT - 5.9L DIESEL -
INSTALLATION, ENGINE COOLANT........7-47
THERMOSTAT - 5.9L DIESEL -
OPERATION, ENGINE COOLANT..........7-46
THERMOSTAT - 5.9L DIESEL -
REMOVAL, ENGINE COOLANT.............7-47
THERMOSTAT - 8.0L - DESCRIPTION,
ENGINE COOLANT.....................7-48
THERMOSTAT - 8.0L - INSTALLATION,
ENGINE COOLANT.....................7-49
THERMOSTAT - 8.0L - OPERATION,
ENGINE COOLANT.....................7-48
THERMOSTAT - 8.0L - REMOVAL,
ENGINE COOLANT.....................7-49
THERMOSTAT - DIAGNOSIS AND
TESTING................7-42,7-44,7-47,7-48
THERMOSTAT-5.7L - DESCRIPTION,
ENGINE COOLANT.....................7-41
THERMOSTAT-5.7L - INSTALLATION,
ENGINE COOLANT.....................7-43
THERMOSTAT-5.7L - OPERATION,
ENGINE COOLANT.....................7-41
THERMOSTAT-5.7L - REMOVAL, ENGINE
COOLANT............................7-42
THREAD REPAIR - STANDARD
PROCEDURE, ALUMINUM.......21-158,21-318
THREADED HOLE REPAIR -
DESCRIPTION......................Intro.-8
THREADS - STANDARD PROCEDURE,
REPAIR DAMAGED OR WORN . . 9-190,9-240,9-9,
9-94
THROTTLE BODY - DESCRIPTION........14-36
THROTTLE BODY - INSTALLATION.......14-37
THROTTLE BODY - OPERATION.........14-36
THROTTLE BODY - REMOVAL...........14-36
THROTTLE CONTROL CABLE -
INSTALLATION..................14-40,14-84
THROTTLE CONTROL CABLE - REMOVAL . 14-38,
14-83
THROTTLE POSITION SENSOR -
DESCRIPTION.......................14-41
THROTTLE POSITION SENSOR -
INSTALLATION.......................14-43
THROTTLE POSITION SENSOR -
OPERATION.........................14-41
THROTTLE POSITION SENSOR -
REMOVAL..........................14-41
THROTTLE VALVE CABLE -
ADJUSTMENTS.....................21-254
THROTTLE VALVE CABLE - DESCRIPTION . 21-253
TIE DOWN - INSTALLATION, CARGO BOX . 23-38
TIE DOWN - REMOVAL, CARGO BOX.....23-38
TIE ROD END - DIAGNOSIS AND
TESTING, OUTER.....................19-32
TIE ROD END - INSTALLATION
..........19-37
TIE ROD END - INSTALLATION, OUTER
. . . 19-33
TIE ROD END - REMOVAL
..............19-37
TIE ROD END - REMOVAL, OUTER
.......19-32
TILT LEVER KNOB RELEASE -
INSTALLATION
.......................19-16TILT LEVER KNOB RELEASE - REMOVAL . . 19-16
TIMING - DESCRIPTION, VALVE..........9-76
TIMING - DIAGNOSIS AND TESTING,
FUEL INJECTION PUMP...............14-53
TIMING - OPERATION, VALVE............9-76
TIMING - VERIFICATION - STANDARD
PROCEDURE, ENGINE.................9-167
TIMING BELT / CHAIN COVER(S) -
INSTALLATION...................9-171,9-81
TIMING BELT / CHAIN COVER(S) -
REMOVAL......................9-170,9-81
TIMING BELT/CHAIN AND SPROCKETS -
INSPECTION....................9-174,9-84
TIMING BELT/CHAIN AND SPROCKETS -
INSTALLATION...................9-176,9-85
TIMING BELT/CHAIN AND SPROCKETS -
REMOVAL......................9-172,9-83
TIMING CHAIN WEAR - STANDARD
PROCEDURE, MEASURING.............9-167
TIMING CHAIN WEAR, STANDARD
PROCEDURE - MEASURING.............9-77
TIMING CHAIN/TENSIONER -
DESCRIPTION.......................9-229
TIMING CHAIN/TENSIONER - OPERATION . 9-229
TIMING DRIVE SYSTEM - DESCRIPTION . . 9-166
TIMING DRIVE SYSTEM - OPERATION....9-166
TIMING, SPECIFICATIONS - IGNITION......8I-5
TIMING VERIFICATION - SERVICE
PROCEDURE.........................9-77
TIMING VERIFICATION - STANDARD
PROCEDURE........................9-299
TIMING/CHAIN AND SPROCKETS -
INSTALLATION.......................9-228
TIMING/CHAIN AND SPROCKETS -
REMOVAL..........................9-228
TIMING/CHAIN COVER - INSTALLATION . . . 9-227
TIMING/CHAIN COVER - REMOVAL.......9-227
TIP INSERTS - INSTALLATION, SPRING....2-45
TIP INSERTS - REMOVAL, SPRING........2-44
TIP REPLACEMENT - STANDARD
PROCEDURE, LIGHT DUTY FRONT
FRAME RAIL.........................13-4
TIRE - DESCRIPTION, FULL SIZE, SPARE
WHEEL WITH MATCHING..............22-15
TIRE - DESCRIPTION, SPARE /
TEMPORARY........................22-15
TIRE / TEMPORARY - DESCRIPTION,
SPARE..............................22-6
TIRE AND WHEEL BALANCE -
STANDARD PROCEDURE................22-4
TIRE AND WHEEL RUNOUT - DIAGNOSIS
AND TESTING........................22-1
TIRE INFLATION PRESSURES -
DESCRIPTION........................22-7
TIRE NOISE OR VIBRATION - DIAGNOSIS
AND TESTING........................22-7
TIRE PRESSURE FOR HIGH SPEEDS -
DESCRIPTION........................22-7
TIRE REVOLUTIONS PER MILE,
SPECIFICATIONS.....................22-10
TIRE ROTATION - STANDARD
PROCEDURE.........................22-3
TIRE WEAR PATTERNS - DIAGNOSIS
AND TESTING........................22-8
TIRES - DESCRIPTION.................22-6
TIRES - DESCRIPTION, RADIAL - PLY.....22-6
TIRES - DESCRIPTION, REPLACEMENT....22-7
TIRE/VEHICLE LEAD - DIAGNOSIS AND
TESTING............................22-8
TOE ADJUSTMENT - STANDARD
PROCEDURE..........................2-4
TOE ADJUSTMENT - STANDARD
PROCEDURE, CAMBER, CASTER
..........2-4
TOOL - ADJUSTMENT, WITH ADJUSTING
. . . 5-42
TOOLS - 4.7L ENGINE, SPECIAL
.........9-103
TOOLS - 5.7L ENGINE, SPECIAL
.........9-196
TOOLS - 5.9L DIESEL ENGINE, SPECIAL
. . 9-246
TOOLS - 9 1/4 AA, SPECIAL
.............2-30
TOOLS - BASE BRAKES, SPECIAL
.........5-5
TOOLS - BATTERY SYSTEM SPECIAL
TOOLS, SPECIAL
......................8F-7
TOOLS - BODY, SPECIAL
...............23-14
TOOLS - COOLING, SPECIAL
.............7-20
TOOLS - DIESEL FUEL SYSTEM,
SPECIAL
...........................14-49
TOOLS - FRONT SUSPENSION, SPECIAL
. . . 2-12
TOOLS - FUEL SYSTEM, SPECIAL
........14-5
DRINDEX 33
Description Group-Page Description Group-Page Description Group-Page