1998 CHEVROLET BLAZER lock

Downloaded from www.Manualslib.com manuals search engine Remote Oil Filter (Four-wheel Drive) Air Cleaner
The access door for the remote oil filter is in the steering
linkage shield assembly located under the radiator
support. Twist the screw to unlock or lock the door.
If you open the door, make sure it is securely closed
when you are finished.
What to Do with Used Oil
Did you know that used engine oil contains certain
elements that may be unhealthy for your skin and could
even cause cancer? Don’t let used oil stay on your skin
for very long. Clean your skin and nails with soap and
water, or a good hand cleaner. Wash or properly throw
away clothing or rags containing used engine oil. (See
the manufacturer’s warnings about the use and disposal
of oil products.)
Used oil can be a real threat to the environment. If you To
remove the air cleaner, remove the wing nuts that
from the filter before disposal. Don’t ever dispose of oil
air
change your own oil, be sure to all free-flowing oil hold the cover on. Remove the cover and lift Out the
by putting it in the trash,-pouring it on the ground, into
sewers, or into streams or bodies of water. Instead,
recycle it by taking it to a place that collects used oil.
If
you have a problem properly disposing of your used oil,
ask your dealer, a service station or a local recycling
center for help. Insert a
new
air filter, then replace the air cleaner cow
Tighten the wing nuts to hold the cover in place. x.
6-14

Downloaded from www.Manualslib.com manuals search engine 2. Push it back in all the way, wait three seconds and
then pull it back out again.
3. Check both sides of the dipstick, and read the lower
level. The fluid level must be in the
COLD area for a
cold check or in the HOT area
or cross-hatched area
for a hot check.
4. If the fluid level is in the acceptable range, push the
dipstick back in all the way; then flip the handle
down to lock the dipstick in place.
How to Add Fluid
Refer to the Maintenance Schedule to determine what
kind of transmission fluid to
use. See “Recommended
Fluids and Lubricants” in the Index.
Add fluid only after checking the transmission fluid
while it is hot. (A cold check is used only as a
reference.) If the fluid level is
low, add only enough
of the proper fluid to bring the level up to the HOT
area for
a hot check. It doesn’t take much fluid,
generally less than one pint
(0.5 L). Don’t oveflll.
NOT.ICE:
We recommend you use only fluid labeled
DEXRON@-111, because fluid with that label is
made especially
for your automatic transmission.
Damage caused by fluid other than DEXRON-I11
is not covered by your new vehicle warranty.
After adding fluid, recheck the fluid level as
When the correct fluid level is obtained, push the
described under “How
to Check.”
dipstick back in all the way; then flip the handle
down to lock the dipstick in place.
6-18

Downloaded from www.Manualslib.com manuals search engine Ttvo-Piece Front Tbrn Signal Lamp Assembly
1. Remove the headlamp assembly as shown under
“Two-Piece Composite Headlamp System” earlier in
this section.
2. Locate the locking
tabs on the
assembly. Squeeze
the tabs together
and push that end
of the assembly out
while holding the
tabs. The assembly
will swing out.
4.
5.
3. Unplug the electrical connector. 6.
7.
Turn the harness bulb socket to the left to remove it.
Push the new bulb into the socket until it snaps
into place.
Put the new bulb into the headlamp lens assembly
and turn it to the right until it is tight.
To replace the assembly, snap the outboard end of
the lamp assembly back into the vehicle. Then swing
the assembly
in and snap it into place.
6-37

Downloaded from www.Manualslib.com manuals search engine Taillamps
I. Open the endgate.
2. Remove the two screws
from the lamp assembly.
3. Pull the assembly away from the vehicle.
4. Turn the socket to the left to remove it. Push the tab
in while you turn the socket to the left.
5. Holding the base of the bulb, pull the bulb straight
out
of the socket.
6. Push the new bulb straight into the socket until
it clicks.
7. Put the socket into the lamp assembly and turn the
socket to the right until
it locks into place.
8. Install the lamp assembly and screws.
9. Close the endgate.
Windshield Wiper Blade Replacement
See “Normal Maintenance Replacement Parts” in the
Index for the proper type
of replacement blade.
r;;OTICE: I
Use care when removing or installing a blade
assembly. Accidental bumping can cause the arm
to fall back and strike the windshield.
1. To remove the old wiper blades, lift the wiper arm
until it locks into a vertical position.
6-38

Downloaded from www.Manualslib.com manuals search engine A. Blade Assembly
B. Arm Assembly
C. Locking Tab
D. Blade Pivot
E. Hook Slot
E Arm Hook
2. Press down on the blade assembly pivot locking tab.
Pull down on the blade assembly to release it from
the wiper arm hook.
3. Remove the insert from the blade assembly. The
insert has two notches at one end that are locked by
the bottom claws
of the blade assembly. At the
notched end, pull the insert from the blade assembly.
A
0
I
4. To install the new wiper insert, slide the insert (D),
notched end last, into the end with two blade claws
(A). Slide the insert all the way through the blade
claws at the opposite end
(B). The plastic caps (C)
will be forced off as the insert is fully inserted.
6-39

Downloaded from www.Manualslib.com manuals search engine 5. Be sure that the notches are locked by the bottom
claws. Make sure that all other claws are properly
locked on both sides
of the insert slots.
B w C
A. Claw in Notch
B. Correct Installation
C. Incorrect Installation
6. Put the blade assembly pivot in the wiper arm
hook. Pull up until the pivot locking tab locks in
the hook slot.
7. Carefully lower the wiper arm and blade assembly
onto the windshield.
Backglass Wiper Blade Replacement
See “Windshield Wiper Blade Replacement” in this
section for instructions on how to change the backglass
wiper blade. The backglass wiper blade will not lock
in a vertical position like the windshield wiper blade,
so care should be used when pulling it away from
the vehicle.
lour new vehicle
comes with high-quality tires made by
a leading tire manufacturer. If you ever have questions
about your tire warranty and where to obtain service, see
your
GM Warranty booklet for details.
6-40

Downloaded from www.Manualslib.com manuals search engine Instrument Panel Fuse Block
Remove the cover by turning the fastener to the left.
Extra fuses and the fuse extractor
are provided in the
cover.
To reinstall the fuse panel cover, push in and turn
the fastener to the right.
Fuse/Circuit
Breaker Usage
A
B
1
Not Used
Not Used
Headlamp Switch, Body Control
Module, Headlamp Relay

Downloaded from www.Manualslib.com manuals search engine Fuse/Circuit Breaker Usage
2
3
4
8
9
10
11
12 Cigarette
Lighter, Data
Link Connector
Cruise Control Module and Switch,
Body Control Module, Heated Seats
Gages, Body Control Module,
Instrument Panel Cluster
Interior Lights
Not Used
Power Outside Mirror, Power
Lock Relay
Courtesy Lamps, Battery Run-Down
Protection
HVAC Control Head (Manual)
Turn Signal Cluster, Engine Control Module
Parking Lamps, Power Window
Switch, Body Control Module,
Ashtray Lamp
FuseKircuit
Breaker Usage
13
14
15
16
17
18
19
20
21
22 23
24 Auxiliary Power
Power Locks Motor
4WD Switch, Engine Controls
(VCM, PCM, Transmission)
Supplemental Inflatable Restraint,
SDM Module
Front Wiper
Not Used
Radio Battery
Not Used HVAC (Manual), HVAC
I
(Automatic), HVAC Sensors
(Automatic)
Anti-Lock Brakes
Rear Wiper
Radio, Ignition
6-61