1998 BUICK REGAL Owners Manual

6. Feed a small amount of harness slack back into
the slot.
7. mist the harness slightly to remove it from the slot.
8. Move the harness up or down to the correct slot. The
correct slot is the one that will be at
or just above the
top of the child's shoulder.
1-41
ProCarManuals.com

9. Twist the harness slightly to route it through the
correct slot.
10.
11.
12.
13.
Pull on the harness. Make sure it is properly routed
and isn't twisted or flipped over.
Repeat Steps
5 through 10 for the other side of
the harness. Be sure both sides are adjusted to the
same height.
Move the pad back against
the child restraint
seatback. Make sure the harness goes through the slots in the pad that match the height adjustment
slots being used.
Press the upper edge of
the pad against the
fastener strip.
1-42
ProCarManuals.com

Securing a Child in the Built-in
Child Restraint
Now that the harness is adjusted to the correct height for
your child, you’re ready to use the child restraint’s
harness (E) to secure your child.
Don’t use the vehicle’s safety belts.
Using the vehicle’s regular safety belts on a child
seated on the child restraint cushion can cause
serious injury to the child in a sudden stop or
crash.
If a child is the proper size for the built-in
child restraint, secure the child using the child
restraint’s harness. But children who are too
large for the built-in child restraint should sit on
the vehicle’s regular seat and use the regular
safety belts.
WARNING! FAILURE TO FOLLOW THE
MANUFACTURER’S INSTRUCTIONS
ON THE USE
OF THIS CHILD RESTRAINT SYSTEM CAN
RESULT IN YOUR CHILD STRIKING THE
VEHICLE’S INTERIOR DURING
A SUDDEN STOP
OR CRASH.
SNUGLY ADJUST THE BELTS PROVIDED WITH
THIS CHILD RESTRAINT
AROUND YOUR CHILD.
1-43
ProCarManuals.com

1. If the left and right halves of the shoulder harness
clip are fastened together, separate them. 2. If the lap-shoulder harness is buckled, unlatch it by
pushing the button on the buckle.
3. Place the child on the child restraint cushion.
1-44
ProCarManuals.com

4. Select only one side of the harness. Pull the lap part
of the harness out, and place the harness over the
child’s shoulder.
If both sides of the harness are pulled out, the lap
parts will lock.
If the lap parts lock, let both sides of
the harness go back all the way so each side will
move freely again. Then repeat this step, pulling
only one side of the harness out.
5. Push the latch plate (F) into the buckle until it clicks.
Be sure the buckle is free of any foreign objects that
may prevent you from securing the latch plates.
If
you can’t secure a latch plate, see your dealer for
service before using the child restraint.
6. In a single motion, pull the other side of the harness
all the way out. Keeping the harness pulled all the
way out, place it over the child’s shoulder.
1-45
ProCarManuals.com

7. Push the latch plate into the buckle until it clicks.
Pull on both latch plates to make sure they are
LQC~. A green indkatw will show in each latch
plate
window ((3).
If the harness locks befme the latch plate reaches the
buckle, let the harness go all the way back SO it will
move fjreely again.
Then repeat Steps 6 and 7. Be
sure to keep the lamess pulled all the way out until
you buckle it.
Qnce both sides of the lap-shoulder harness ae
pulled out of the retractor and buckled, the hmess
will lock.
ProCarManuals.com

8. Now fasten the left and right halves of the shoulder
harness clip together. The indicator window
(H) on
the clip will show green when the two halves are
fastened together. The purpose of this clip
is to help
keep the harness positioned
on the child’s shoulders.
A CAUTION:
An unfastened shoulder harness clip won’t help
keep the harness in place on the child’s shoulders.
If the harness isn’t on the child’s shoulders, it
won’t be able to restrain the child’s upper body
in a sudden stop or crash. The child could be
seriously injured. Make sure the harness clip is
properly fastened.
1-47
ProCarManuals.com

If the harness still doesn’t lock, don’t use the child
restraint. See your dealer to have the built-in child
restraint serviced.
9. On both sides of the harness, pull up on the lap part a
little to be sure it’s locked.
If the harness isn’t locked, or if it becomes too tight,
unfasten the harness clip.
Then unlatch the harness
by pushing the button on
the buckle, and let both
sides of the harness go all the way back
so they will
move freely again. Then, repeat Steps
4 through 8.
10. Adjust the position of the harness on the child’s
shoulders by moving the clip
up or down along the
harness. On each side
of the harness, the shoulder
part should be centered on the child’s shoulder. The
harness
should be away from the child’s face and
neck, but not falling off the child’s shoulders.
1-48
ProCarManuals.com