1997 TOYOTA SUPRA wheel torque

R06915
SA0028
AB
Front
A: Inside
B: OutsideA B
- SUSPENSION AND AXLEFRONT WHEEL ALIGNMENT
SA-5
1695 Author
: Date
:
1997 SUPRA (RM502U)
(c) Turn the left and right rack ends an equal amount to adjust
the toe-in.
HINT:

Make sure that the lengths of the left and right rack ends
are the same.

Try to adjust the toe-in to the center value.
Rack end length difference:
1.5 mm (0.059 in.) or less
(d) Tighten the tie rod end lock nut.
Torque: 56 N´m (570 kgf´cm, 41 ft´lbf)
(e) Place the boot on the seat and clip it.
HINT:
Make sure that the boots are not twisted.
7. INSPECT WHEEL ANGLE
Turn the steering wheel fully and measure the turning angle.
2JZ-GE2JZ-GTE
Inside wheel35°00' (33°00' - 36°00')
35° (33° - 36°)34°55' (33°55' - 36°55')
34.92° (32.92° - 35.92°)
Outside wheel
30°45'
(30.75°)30°35'
(30.58°)
If the wheel angle are not within the specifications, check to see
if the lengths of the left and right rack ends are the same.
HINT:
If the tie rods lengths are not equal, the wheel angle cannot be
adjusted properly. Reinspect the toe-in after adjusting the tie
rods lengths.

R06947
Z18438
Example
Camber
Toe-in
R05675
Front
LHRH + (Longer) - (Shorter) - (Shorter)
- (Shorter) - (Shorter) + (Longer) + (Longer)+ (Longer)
- SUSPENSION AND AXLEREAR WHEEL ALIGNMENT
SA-9
1699 Author
: Date
:
1997 SUPRA (RM502U)
(d) Loosen and adjust the No.1 and/or No.2 cams.
(e) Adjust camber and toe-in by turning the No.1 and/or No.2
cams (See adjustment chart).
HINT:
Try to adjust the camber and toe-in to the center value.
(f) Torque the No.1 and/or No.2 cam nuts.
Torque: 184 N´m (1,880 kgf´cm, 136 ft´lbf)
(g) Connect the parking brake cable bracket with the bolt.
6. HOW TO READ ADJUSTMENT CHART
(a) Mark on the graph the measurements taken from vehicle.
Example (2JZ-GTE):
Camber (LH): -1°00' (-1°)
Camber (RH): -1°30' (-1.5°)
(b) Read from the graph the amounts of the front and/or rear
cam to be adjusted.
Amount to turn adjusting cam (by graduation)
LH Front cam: + (Longer) 1.1
LH Rear cam: + (Longer) 3.0
RH Front cam: - (Shorter) 1.0
RH Rear cam: + (Longer) 0.9

SA0OU-02
R11096
SA3535SST SA-12
- SUSPENSION AND AXLEFRONT AXLE HUB
1702 Author
: Date
:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE BRAKE CALIPER AND DISC
(a) Remove the 2 bolts and brake caliper from the steering
knuckle.
Torque: 118 N´m (1,200 kgf´cm, 87 ft´lbf)
(b) Support the brake caliper securely.
(c) Place matchmarks on the disc and axle hub.
(d) Remove the disc.
3. CHECK BEARING BACKLASH AND AXLE HUB DEVI-
ATION
(a) Using a dial indicator near the center of the axle hub and
check the backlash in the bearing shaft direction.
Maximum: 0.05 mm (0.0020 in.)
If the backlash exceeds the maximum, replace the bearing.
(b) Using a dial indicator, check the deviation at the surface
of the axle hub outside the hub bolt.
Maximum: 0.05 mm (0.0020 in.)
If the deviation exceeds the maximum, replace the bearing.
4. DISCONNECT ABS SPEED SENSOR FROM STEER-
ING KNUCKLE
Remove the bolt and disconnect the ABS speed sensor from
the steering knuckle.
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
5. DISCONNECT TIE ROD END FROM STEERING
KNUCKLE
(a) Remove the cotter pin and nut.
Torque: 49 N´m (500 kgf´cm, 36 ft´lbf)
(b) Using SST, disconnect the tie rod end from the steering
knuckle.
SST 09611-12010

SA0OY-01
R07035
SST
R07036
SA-18
- SUSPENSION AND AXLEFRONT WHEEL HUB BOLT
1708 Author
: Date
:
1997 SUPRA (RM502U)
FRONT WHEEL HUB BOLT
REPLACEMENT
1. REMOVE FRONT WHEEL
2. REMOVE BRAKE CALIPER AND DISC
(a) Remove the 2 bolts and brake caliper from the steering
knuckle.
(b) Support the brake caliper securely.
(c) Place matchmarks on the disc and axle hub.
(d) Remove the disc.
3. REMOVE HUB BOLT
Using SST, remove the hub bolt.
SST 09628-1001 1
4. INSTALL HUB BOLT
(a) Install washer and nut to a new hub bolt, as shown in the
illustration.
(b) Turn the wheel nut to pull the hub bolt through until the un-
derside of the hub bolt head touches the axle hub.
5. INSTALL DISC AND BRAKE CALIPER
(a) Install the disc.
(b) Install the 2 bolts and brake caliper to the steering
knuckle.
Torque: 118 N´m (1,200 kgf´cm, 87 ft´lbf)
6. INSTALL FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)

SA0P0-01
SA3578
R00159
SA-20
- SUSPENSION AND AXLEFRONT SHOCK ABSORBER
1710 Author
: Date
:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE BRAKE CALIPER
(a) Remove the 2 bolts and brake caliper from the steering
knuckle.
Torque: 118 N´m (1,200 kgf´cm, 87 ft´lbf)
(b) Support the brake caliper securely.
3. DISCONNECT ABS SPEED SENSOR AND WIRE HAR-
NESS
(a) Remove the bolt and disconnect the speed sensor from
the steering knuckle.
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
(b) Remove the 3 bolts and disconnect the wire harness
clamp to prevent the wire harness from being damaged
when removing or installing the through bolt of the upper
suspension arm.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
4. REMOVE FRONT FENDER SPLASH SHIELD
5. LH side only:
MOVE WASHER TANK
(a) Remove the 2 washer tank set bolts.
(b) Move the washer tank away from the body.
6. DISCONNECT UPPER SUSPENSION ARM
(a) Remove the bolt and nut and disconnect the upper sus-
pension arm from the sub-frame.
Torque: 164 N´m (1,670 kgf´cm, 121 ft´lbf)
HINT:
At the time of installation, after stabilizing the suspension,
torque the nut.
(b) Support the upper suspension arm securely.
7. DISCONNECT STABILIZER BAR LINK
Remove the nut and disconnect the stabilizer bar link.
Torque: 74 N´m (750 kgf´cm, 54 ft´lbf)
HINT:
If the ball joint stud turns together with the nut, use a hexagon
wrench to hold the stud.

SA0P8-01
SA3578
R07239
SST
- SUSPENSION AND AXLEFRONT UPPER SUSPENSION ARM
SA-29
1719 Author
: Date
:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE BRAKE CALIPER
(a) Remove the 2 bolts and brake caliper from the steering
knuckle.
Torque: 118 N´m (1,200 kgf´cm, 87 ft´lbf)
(b) Support the brake caliper securely.
3. DISCONNECT ABS SPEED SENSOR AND WIRE HAR-
NESS CLAMP
(a) Remove the bolt and disconnect the speed sensor from
the steering knuckle.
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
(b) Remove the 3 bolts and disconnect the wire harness
clamp to prevent the wire harness being damaged when
removing or installing the through bolt.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
4. DISCONNECT UPPER SUSPENSION ARM
(a) Remove the cotter pin and the nut.
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
(b) Using SST, disconnect the upper suspension arm from
the steering knuckle.
SST 09628-6201 1
5. REMOVE FRONT FENDER SPLASH SHIELD
6. LH side only:
MOVE WASHER TANK
(a) Remove the 2 washer tank set bolts.
(b) Move the washer tank away from the body.
7. REMOVE UPPER SUSPENSION ARM
(a) Remove the nut, 2 washers and bolt.
Torque: 164 N´m (1,670 kgf´cm, 121 ft´lbf)
HINT:
At the time of installation, after stabilizing the suspension,
torque the nut.
(b) Remove the upper suspension arm.

SA0PD-01
R00159
R07240
SST
R06928
- SUSPENSION AND AXLEFRONT LOWER SUSPENSION ARM
SA-33
1723 Author
: Date
:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE ENGINE UNDER COVER
3. REMOVE BRAKE CALIPER
(a) Remove the 2 bolts and brake caliper from the steering
knuckle.
Torque: 118 N´m (1,200 kgf´cm, 87 ft´lbf)
(b) Support the brake caliper securely.
4. DISCONNECT STABILIZER BAR LINK FROM SHOCK
ABSORBER BRACKET
Remove the nut and disconnect the stabilizer bar link from the
shock absorber bracket.
Torque: 74 N´m (750 kgf´cm, 54 ft´lbf)
HINT:
If the ball joint stud turns together with the nut, use a hexagon
wrench to hold the stud.
5. DISCONNECT STEERING KNUCKLE
(a) Remove the clip and nut.
Torque: 125 N´m (1,270 kgf´cm, 92 ft´lbf)
(b) Using SST, disconnect the steering knuckle from the low-
er suspension arm.
SST 09628-6201 1
6. REMOVE LOWER SUSPENSION ARM
(a) Remove the nut, washer and bolt and disconnect the low-
er suspension arm from the shock absorber.
Torque: 143 N´m (1,460 kgf´cm, 106 ft´lbf)
HINT:
At the time of installation, after stabilizing the suspension,
torque the nut.
(b) Remove the nut, 2 bolts and the lower suspension arm
bracket stay.
Bolt: 44 N´m (450 kgf´cm, 32 ft´lbf)
Nut: 59 N´m (600 kgf´cm, 43 ft´lbf)
HINT:
At the time of installation, before installing the lower suspension
arm bracket stay, adjust the front wheel alignment.

SA0PH-01
R07309
R07310
Z18434
Paint Line SA-38
- SUSPENSION AND AXLEFRONT STABILIZER BAR
1728 Author
: Date
:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE FRONT WHEELS
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE ENGINE UNDER COVER
3. REMOVE LEFT AND RIGHT FRONT FENDER SPLASH
SHIELDS
4. REMOVE BOTH STABILIZER BAR LINKS
(a) Remove the 2 nuts and stabilizer bar link from the stabiliz-
er bar and the lower suspension arm.
Torque: 74 N´m (750 kgf´cm, 54 ft´lbf)
HINT:
If the ball joint stud turns together with the nut, use a hexagon
wrench to hold the stud.
(b) Employ the same manner described above to the other
side.
5. REMOVE STABILIZER BAR
(a) Remove the left and right apron seal set bolts.
(b) Remove the 4 bracket bolts and the stabilizer bar with the
2 bushings and brackets.
Torque: 18 N´m (180 kgf´cm, 13 ft´lbf)
6. REMOVE CUSHIONS AND BRACKETS
HINT:
At the time of installation, install the cushion to the outside of the
paint line.