1997 TOYOTA 4RUNNER Owners Manual

212If the new fuse immediately blows out, there is a problem with the electrical sys-
tem.
Have your Toyota dealer correct it as
soon as possible.
Never use a fuse with a higher
amperage rating, or any other
object, in place of a fuse. This maycause extensive damage and
possibly a fire. CAUTION
!
If any washer does not work, the wash-
er tank may be empty. Add washer fluid.
You may use plain water as washer fluid.
However, in cold areas where tempera-
tures range below freezing point, use
washer fluid containing antifreeze. This
product is available at your Toyota dealer
and most auto parts stores. Follow the
manufacturer 's directions for how much
to mix with water.
NOTICE
Do not use engine antifreeze or any other substitute because it may
damage your vehicle's paint.
The following illustrations show how to
gain access to the bulbs. When replacing
a bulb, make sure the ignition switch and
light switch are off. Use bulbs with the wattage ratings given in the table.
NOTICE
Only use a bulb or unit of the listed type.
Adding washer fluid Replacing light bulbsÐ

213
Light bulbs
Bulb
No.WType
HeadlightÐ60/5 5A
Parking and front side marker lightsÐ5C
Front turn signal lights115627B
Rear turn signal lightsÐ21C
Stop and tail lightsÐ21/5C
Back-up lightsÐ21C
License plate lightÐ5C
High mounted stop light92118C
Interior lightÐ8D
Personal lightsÐ8D
Glovebox lightÐ1.4C
Luggage compart- ment lightÐ8D
A: HB2 halogen bulbs B: Single end bulbs
C: Wedge base bulbsD: Double end bulbs
1. Open the hood. Unplug the con-
nector. Remove the rubber cover.
If the connector is tight, wiggle it.2. Release the bulb retaining spring and remove the bulb. Install a new
bulb and the bulb retaining spring.
To install a bulb, align the tabs of the bulb with the cutouts of the mounting hole.
ÐHeadlights

214
3. Install the rubber cover, snuggle on
the boss. Inset the connector.
Make sure the rubber cover fits snugly on
the connector and the headlight body.
Aiming is not necessary after replacing
the bulb. When aiming adjustment is nec-
essary, contact your Toyota dealer.Use a Phillips-head screwdriver.
ÐParking and front side marker lights

215
Use a Phillips-head screwdriver.Use a Phillips-head screwdriver.a: Back-up light
b: Rear turn signal lights
c: Stop and tail lights
ÐFront turn signal lights
ÐRear turn signal, stop and tail, and back-up lights

216
Use a Phillips-head screwdriver.Use a Phillips-head screwdriver.
ÐLicense plate lights ÐHigh mounted stoplight

P265/70R 16 tire
Without wheel opening extension With wheel opening extension
P225/75R 15 tire
Overall length Overall widthOverall heightWheel base Front tread Rear tread 4540 (178.7)1690 ( 66.5)1715 ( 67.5)*2675 (105.3) 1505 ( 59.3) 1495 ( 58.9) 4540 (178.7)1730 ( 68.1)1760 ( 69.3)*2675 (105.3) 1505 ( 59.3) 1510 ( 59.4)4540 (178.7)1800 ( 70.9)1760 ( 69.3)*2675 (105.3) 1505 ( 59.3) 1510 ( 59.4)
Cargo weight rating kg (lb.): 200 (300)
*: Unladen vehicle mm (in.)
Part 8
Dimensions and weight
217
SPECIFICATIONS
Dimensions and weight
Engine
Fuel
Service specifications
Tires
Fuses

+25 -15
218
Model:
3RZ-FE and 5VZ-FE
Type: 3RZ-FE engine4 cylinder in line, 4 cycle, gasoline
5VZ-FE engine 6 cylinder V type 4 cycle, gasoline
Bore and stroke, mm (in.):
3RZ-FE engine95.0 x 95.0 (3.74 x 3.74)
5VZ-FE engine
93.5 x 82.0 (3.68 x 3.23)
Displacement, cm 3
(cu. in.):
3RZ-FE engine
2694 (164.3)
5VZ-FE engine 3378 (206.1) Fuel type:
Unleaded gasoline, Research OctaneNumber 91 (Octane Rating 87) or higher
Fuel tank capacity, L (gal., Imp. gal.):
70 (18.5, 15.4) ENGINE
Valve clearance (engine cold), mm (in.)
3RZ-FE engine
Intake 0.15 '0.25 (0.006 '0.010)
Exhaust 0.25 '0.35 (0.010 '0.014)
5VZ-FE engine
Intake 0.13 '0.23 (0.006 '0.009)
Exhaust 0.27 '0.37 (0.011 '0.014)
Spark plug type:
3RZ-FE enginesNIPPONDENSO K16R-U
NGK BKR5EYA
5VZ-FE engine
NIPPONDENSO K16TR11
NGK BKR5EKB11
Spark plug gap, mm (in.): 3RZ-FE engine 0.8 (0.031)
5VZ-FE engine 1.1 (0.043)
Drive belt tension measured with Bor-
roughs drive belt tension gauge No.
BT-33-73F (used belt), lbf: 3RZ-FE engineGenerator belt 115 + 20
Air conditioning compressor belt 100 + 20
Power steering pump belt 100
Service specifications
Fuel
Engine

+20 -15219
5VZ-FE engine
Generator belt 100 + 20
Air conditioning compressor belt 100 + 20
Power steering
pump belt 100
ENGINE LUBRICATION Oil capacity (drain and refill), L (qt., Imp. qt.): 3RZ-FE engineWith filter 5.4 (5.7, 4.8)
Without filter 4.9 (5.0, 4.1)
5VZ-FE engine With filter 5.2 (5.5, 4.6)
Without filter 4.9 (5.2, 4.3) Oil grade:
API SH, Energy-Conserving IIº multi-
grade engine oil or ILSAC multigrade en-
gine oil is recommended. Recommended oil viscosity (SAE):
COOLING SYSTEM
Total capacity, L (qt., Imp. qt.):
3RZ-FE engineWith rear heater 11.0 (11.6, 9.7)
Without rear heater 10.0 (10.6, 8.8)
5VZ-FE engine With rear heater
9.0 (9.5, 7.9)
Without rear heater
8.0 (8.5, 7.0) Coolant type: With ethylene-glycol antifreeze (Do not use alcohol type.)
BATTERY ÐMaintenance type battery
Specific gravity reading at 20
C (68 F):
1.280 Fully charged1.180 Half charged 1.080 Discharged
ÐNon-maintenance batteryOpen voltage* at 20 C (68 F):
12.7 V Fully charged12.3 V Half charged
11.9 V Discharged
*: Voltage that is checked 20 minutes af-
ter the key is removed with all the lights
turned off
Charging rates:
Non-maintenance battery 5 A max. Maintenance type battery
Quick charge 15 A max.
Slow charge 5 A max.
CLUTCH
Pedal freeplay, mm (in.): 5Ð15 (0.2Ð0.6)Fluid type:
SAE J1703 or FMVSS No. 116 DOT 3