1997 SUBARU LEGACY dimensions

3. FRONT WINDSHIELD AND REAR WINDOW
B5M0254A
Unit: mm (in)
18
5-1SERVICE DATA
3. Datum Dimensions

4. DOORS
B5M0321A
Unit: mm (in)
19
5-1SERVICE DATA
3. Datum Dimensions

5. TRUNK LID AND REAR GATE
B5M0255A
Unit: mm (in)
20
5-1SERVICE DATA
3. Datum Dimensions

6. COMPARTMENT
B5M0256A
Unit: mm (in)
21
5-1SERVICE DATA
3. Datum Dimensions

4. Datum Points and Dimensions
Concerning On-Board Aiming
Adjustment
If headlight aiming is misaligned due to damaged body
panel, repair headlight mating surface using body and
headlight datum points as a guide.
NOTE:
It is recommended to conduct On-Board Aiming Adjust-
ment with headlights turned off.
If turned on during the adjustment, the duration should be
within two minutes.
B5M0364
Unit: mm (in)
22
5-1SERVICE DATA
4. Datum Points and Dimensions Concerning On-Board Aiming Adjustment

2. PROCEDURE CHART FOR ADJUSTING DOOR
GLASS
Insert door glass.
Mount door glass on regulator.
Install front and rear upper stoppers.

Install inner stabilizer.
Align upper stopper position.
Align adjusting bolt with nut.
Remedy for unequal dimensions

Remedy for improper window glass-to-center
pillar clearance

Remedy for improper window glass-
to-weatherstrip contact

Not O.K. Not O.K. Not O.K.
Close the door and check all clearances are as specified.
O.K.
END









21
5-2SERVICE PROCEDURE
2. Door

3) Lower door glass 10 to 15 mm (0.39 to 0.59 in) from
fully closed position. While applying outward pressure
(load) to upper edge of glass above midpoint of two outer
stabilizers, press inner stabilizer until it just touches the
glass, then secure it.
Load: F
Front door glass 39 N (4 kg, 9 lb)
Rear door glass 34.3 N (3.5 kg, 7.7 lb)
G5M0498
Remedy for unequal dimensions, between upper,
lower and center pillar sides
1) Close front door and raise door glass.
2) Make sure of unequal dimensions.
B5M0073A
3) If glass tilts to far rearward, loosen adjusting nut
Cand
adjust glass to be parallel with center pillar, then after
adjustment, tighten adjusting nut

C.
B5M0074A
Remedy for improper glass to center pillar clearance
1) Close front door and raise door glass.
2) Make sure of improper clearance.
23
5-2SERVICE PROCEDURE
2. Door

B5M0075A
3) If clearance is improper, loosen adjusting nut
A, bolt
A
and adjust glass to center pillar.
G5M0511
Remedy for improper upper stop point of door glass
1) Loosen front and rear sash stoppers.
2) Increase the upward travel of window glass up to the
position where upper edge just touches weatherstrip sur-
face with door closed.
3) After adjustment, temporarily tighten stoppers.
NOTE:
Make sure that each glass stopper is touched.
B5M0076A
Remedy for incorrect contact of door glass to weath-
erstrip
1) Close front door and raise door glass.
2) If clearance is below specifications, loosen bolt

Aand
bolt

B.
3) If clearance is over specifications, tighten bolt

Aand
bolt

B.
B5M0076A
Fit adjustment
Door glass fit is adjusted by displacing the glass front edge
with a stabilizer.
NOTE:
Before adjusting glass fit, visually check to determine rela-
tive adjusting positions of retainer and molding (on roof
side) and glass surface.
1) Alternately adjust two rear sash adjusting bolts

Auntil
dimensions (indicated in figure) are obtained.
CAUTION:
Do not loosen two adjusting nuts

Aat the same time,
as this moves sash fore and aft, creating unequal
glass-to-sash clearance. During adjustment, loosen
only one nut and keep the other tightened.
24
5-2SERVICE PROCEDURE
2. Door