1997 RENAULT KANGOO light

UPPER REAR STRUCTURE
Lights mounting side panel rain channel
44F
PRB4418
INTRODUCTION
The replacement of this part may be carried out in
two ways :
1 - Complete replacement, complementary to the
side panel with lining.
2 - Partial replacement, complementary to the
rear end panel and rear end cross member
(see cut in the diagram below).
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning other parts will be dealt
with in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with :
- side panel extension,
- lights mounting with studs and welded nuts,
- bumper counter blade,
- tailgate counter balance reinforcement,
- welded nuts,
- upper hinge reinforcement.
JOINTS WITH:
Panel upper rain channel
Side panel lining
Rear floor
Rear end cross member
Roof stretcher lining
Roof
PARTS CONCERNED (thickness in mm):
1Lights mounting side panel rain
channel 1.5
2Panel upper rain channel 1.2
3Panel lining 0.7
4Rear floor 0.8
5Rear end cross member 1.02
6Roof stretcher 0.7
7Roof 0.7
8Wheel arch 1
9Side panel 1
10Rear wing panel extension 1
or
44-33

UPPER REAR STRUCTURE
Lights mounting side panel rain channel
44F
13211R1
CAW13605-1R2
A
76
2
CAO11694R4
B
1 6
1 - COMPLETE REPLACEMENT
44-34

UPPER REAR STRUCTURE
Lights mounting side panel rain channel
44F
13212R
CAA11536-3R2
C
17
CAA11536-3R2
D
19
CAA11536-5R2
E
1
7
44-35

UPPER REAR STRUCTURE
Lights mounting side panel rain channel
44F
13223R
CAQ11697R4
F
14
CAU13326R1
G
1
8
CAL11554-2R1
H
1 8 4
10 3
44-36

UPPER REAR STRUCTURE
Lights mounting side panel rain channel
44F
13223R1
2 - PARTIAL REPLACEMENT
or
13351S
CAV13467R3
I
10
10 Appearance after cutting.
44-37

UPPER REAR STRUCTURE
Rear wing panel extension
44G
PRB4419
INTRODUCTION
The replacement of this part is carried out partial-
ly following a rear side impact and is complemen-
tary to the rear wing panel (see diagram and me-
thod below).
The bumper side mounting must also be replaced
and is sold separately.
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning other parts will be dealt
with in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part only.
JOINTS WITH:
Wing panel lining
Lights mounting side panel rain channel
Bumper mounting
PARTS CONCERNED (thickness in mm):
1Rear wing panel extension 1
2Wing panel lining 0.7
3Acoustic insert 0.7
4Bumper mounting 1.2
44-38

TOP OF BODY
Roof
45A
INTRODUCTION
The replacement of this part is a basic operation
for a rollover, or a complementary operation to a
side panel for a side impact.
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning other parts will be dealt
with in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with stiffeners.
PRB4503
JOINTS WITH :
Roof front cross member
Roof centre cross member
Roof rear cross member
Body side
Side panel
Side panel rain channel (lights mounting)
PARTS CONCERNED (thickness in mm):
1Roof 0.8
2Roof front cross member 0.8
3Roof centre cross member 1
4Roof rear cross member 0.8
5Roof rear cross member
reinforcement 1.2
6Side panel 0 .8
7Upper reinforcement of side
panel rain channel 1.2
8Centre pillar door pillar
reinforcement 1.2
9Windscreen pillar lining 1
10Stretcher lining 0.7
11Roof flap rain channel 0.7
45-1

NON-SIDE OPENING ELEMENTS
Bonnet
REFITTING
Refit in the opposite way to removal and refer to
section 40 (opening clearances) to correctly make
adjustments.
ADJUSTMENT
The height adjustment is carried out using strut
mounting bolts (B) on the headlight carrier panel.
The front and rear adjustments are carried out
using mounting nuts (A) on the bonnet .
REMOVAL
48A
PRB4808
13238R
Remove the bonnet nuts (A) (operation must be
carried out by two people).
48-1