1997 RENAULT KANGOO roof

UPPER REAR STRUCTURE
Side panel
44B
PRB4414
INTRODUCTION
The replacement of this part is a basic operation
for a rear side impact.
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning the other parts will be
dealt with in the respective section.
For the panel version, this part may be replaced in
two ways (see cuts on the diagram below) :
1 - complete with cut A.A on the upper section
2 - partial with cut B.B for the glazed version
At the end of the section there are also special de-
tails for the glazed version and the version with a
roof flap.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with sliding door rail units and
striker plate mounting.
JOINTS WITH :
Lights mounting side panel rain channel
Body side lining
Door pillar reinforcement
Wing panel stiffener spacer
PARTS CONCERNED (thickness in mm):
1Rear wing panel 0.8
2Rear wing panel lining 0.7
3Lights mounting side panel rain
channel 1.2
4Rear wing panel extension 1
5Side panel rain channel
upper reinforcement 1.2
6Centre rail mounting 1
7Stretcher lining 0.7
8Roof 0.7
9Door pillar upper reinforcement 1.2
10Door pillar reinforcement 1.2
11Sill panel closure panel 1.5
12Roof flap rain channel 0.7
13Sill panel pillar reinforcement 1.2
14Wing panel stiffener spacer 0.7
15Wing panel stiffener 0.7
44-9

UPPER REAR STRUCTURE
Side panel
44B
VERSION WITH
ROOF FLAP
INTRODUCTION
Below are special details for vehicles fitted with a
roof flap.
13475R
CAC11541-1R6
A
1 2
CAC11541-1R6
B
1 5
44-16

UPPER REAR STRUCTURE
Side panel lining
44C
PRB4415
INTRODUCTION
The replacement of this part is a complementary
operation to the wing panel or a side panel for a
rear side impact.
It also requires replacement of the centre pillar
reinforcement, the door pillar will need to be or-
dered separately.
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning the other parts will be
dealt with in the respective section.
This part is replaced in three ways (see cuts on the
diagram below) :
1 - complete
2 - partial by cut A-A
3 - partial by cut B.B for glazed version
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with welded nuts.
JOINTS WITH :
Door pillar upper reinforcement or centre pillar
reinforcement
Roof stretcher lining
Lights mounting side panel rain channel
Sill panel closure panel
Sill panel closure panel, rear section
Rear wheel arch
Rear end cross member
PARTS CONCERNED (thickness in mm):
1Rear wing panel lining 0.7
2Stretcher lining 0.7
3Lights mounting side panel rain
channel 1.2
4Rear wing panel extension 1
5Side panel rain channel
upper reinforcement 1.2
6Sill panel closure panel 1.5
7Sill panel closure panel, rear section 1.5
8Door pillar upper reinforcement 1.2
9Door pillar lower reinforcement 1.2
10Inertia reel mounting reinforcement 1.5
11Inner wheel arch 1
12Seat mounting reinforcement 1.5
13Rear end cross member 1.2
44-17

UPPER REAR STRUCTURE
Roof stretcher lining
44D
PRB4416
INTRODUCTION
The replacement of this part is a complementary
operation to the wing panel with lining for a side
impact with rollover.
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning other parts will be dealt
with in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with welded nuts.
JOINTS WITH:
Windscreen pillar lining
Centre pillar upper reinforcement
Wing panel upper rain channel
PARTS CONCERNED (thickness in mm):
1Roof stretcher lining 0.7
2Windscreen pillar lining 1
3Wing panel upper rain channel 1.2
4Roof rear cross member 0.8
5Roof rear cross member reinforcement 1.2
6Centre pillar / door pillar
upper reinforcement 1.2
7Upper reinforcement of side
panel rain channel 1.2
8Roof flap rain channel 0.7
44-26

UPPER REAR STRUCTURE
Roof stretcher lining
44D
13214R1
CAA11537-1R5
A
1 2
CAA11538-1R8
B
1
6
44-27

UPPER REAR STRUCTURE
Roof stretcher lining
44D
13211R2
CAA11537R5
C
1
4
CAP11696-2R6
D
1 45
CAJ11551-1R3
E
1
4 5
CAO11694-1R3
F
7
1
44-28

UPPER REAR STRUCTURE
Roof stretcher lining
44D
13475R1
VERSION WITH
ROOF FLAP
CAO11694R6
A
1 8
CAO11694R6
B
7 8
44-29

UPPER REAR STRUCTURE
Lights mounting side panel rain channel
44F
PRB4418
INTRODUCTION
The replacement of this part may be carried out in
two ways :
1 - Complete replacement, complementary to the
side panel with lining.
2 - Partial replacement, complementary to the
rear end panel and rear end cross member
(see cut in the diagram below).
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning other parts will be dealt
with in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with :
- side panel extension,
- lights mounting with studs and welded nuts,
- bumper counter blade,
- tailgate counter balance reinforcement,
- welded nuts,
- upper hinge reinforcement.
JOINTS WITH:
Panel upper rain channel
Side panel lining
Rear floor
Rear end cross member
Roof stretcher lining
Roof
PARTS CONCERNED (thickness in mm):
1Lights mounting side panel rain
channel 1.5
2Panel upper rain channel 1.2
3Panel lining 0.7
4Rear floor 0.8
5Rear end cross member 1.02
6Roof stretcher 0.7
7Roof 0.7
8Wheel arch 1
9Side panel 1
10Rear wing panel extension 1
or
44-33