1997 RENAULT KANGOO Electrical Equipment Workshop Manual

CONTROLS - SIGNALS
Windscreen wiper stalk
REMOVAL - REFITTING
Disconnect the battery.
Remove the two half cowlings under the steering
wheel.
Release the immobiliser antenna ring or the pla-
stic surround from the ignition switch.
Remove the two mounting bolts (A) for the wiper
stalk.
Release the stalk from its mounting and dis-
connect the connector.
84
CONNECTION
12970R
NOTE : the steering wheel does not have to be re-
moved.
13061R
Track Allocation
A1 Front timer
A2 Wiper high speed
A3 Wiper low speed
A4 Front washer pump
A5 Not used
A6 Intermittent slow speed
A7 + after ignition, front wiper
B1 Rear washer pump
B2 Rear timer
B3 Not used
B4 + after ignition, rear wiper
B5 Earth
B6 Not used
B7 Not used
84-1

CONTROLS - SIGNALS
Lights stalk
REMOVAL - REFITTING
Disconnect the battery.
Remove the two half cowlings under the steering
wheel.
Remove the two mounting bolts (B) for the lights
stalk.
Release the stalk from its mounting and dis-
connect the connector.
84
CONNECTION
12970R1
NOTE : the steering wheel does not have to be re-
moved.
13062R
Track Allocation
A1 Front fog lights
A2 Not used
A3 Rear fog light
A4 Horn
A5 Right hand indicators
A6 Central flasher unit
A7 Left hand indicators
B1 Side lights
B2 + before ignition, side lights
B3 + before ignition, dipped headlights
B4 Not used
B5 Dipped headlights
B6 + before ignition, main beam headlights
B7 Main beam headlights
84-2

CONTROLS - SIGNALS
Stalk mounting
REMOVAL - REFITTING
Disconnect the battery and set the wheels
straight.
Remove the steering wheel and the two half cow-
lings (for vehicles with an airbag, refer to the re-
moval of the rotary switch on the following page
or section 88 for special notes on removing the
steering wheel).
Special notes for vehicles with an airbag
Before removing the assembly, the position of the
rotary switch under the steering wheel must be
noted:
- by ensuring that the wheels are straight on re-
moval so that the strip may be positioned in the
centre,
- by immobilising the rotary switch rotor using
adhesive tape.
Slacken the bolt (C) then sharply tap the screwdri-
ver to release the cone.
84
Special notes for refitting
Fit the mounting with its components, connect
the various connectors and push the assembly
back against the steering column.
Continue refitting and do not lock bolt (C) until
the two half cowlings are refitted, so that the
stalks may be aligned with the dashboard and the
instrument panel.
This operation is made easier by a cut-out section
giving access to bolt (C) in the lower half cowling.
For vehicles with an airbag, observe the re-
commendations in the section " Special notes for
the rotary switch under the steering wheel" on
the following page or section 88 (driver’s airbag).
12970R2
Move the stalk mounting assembly back slightly
and disconnect the connectors.
84-3

CONTROLS - SIGNALS
Rotary switch under steering wheel
This makes the electrical connection between the
steering column and the steering wheel.
It consists of a strip of conductor tracks (airbag)
whose length is designed to guarantee 2.5
steering wheel turns (steering lock plus safety
margin) on each side.
REMOVAL - REFITTING
84
- the horn connector, if fitted,
- the steering wheel bolt,
- the steering wheel after setting the wheels
straight,
- the half cowlings (3 bolts).
Disconnect the connector for the rotary switch
and remove it after removing the three mounting
bolts (E).
Before removing the rotary switch its position
must be noted:
- by ensuring that the wheels are straight on re-
moval so that the track may be positioned in
the centre,
- by immobilising the rotary switch rotor using
adhesive tape.
If it is being replaced, the new part is supplied rea-
dy centred by an adhesive label which will tear off
as soon as the steering wheel is turned for the first
time (fit with the wheels straight).
12970R3
Disconnect the battery.
Remove:
- the airbag cushion by the two torx T30 bolts
(tightening torque : 0.5 daN.m) located behind
the steering wheel and disconnect the connec-
tor (D),
IMPORTANT: It is not permitted to operate the
pyrotechnical systems (airbags and pretensioners)
near a source of heat or flame as there is a risk of
triggering.
IMPORTANT : If the steering wheel is removed,
the airbag connector (D)
MUST be disconnected.
The airbag has a connector which short circuits if
it is disconnected to prevent incorrect triggering.
12973R
84-4

CONTROLS - SIGNALS
Rotary switch under steering wheel
Special notes for refitting
Ensure the wheels are still straight.
Ensure the rotary switch under the steering wheel
is still immobilised before refitting.
If there is any doubt follow the method for cen-
tring described in section 88 "driver’s airbag".
Renew the steering wheel bolt each time it is re-
moved (pre-bonded bolt).
Observe the correct tightening torque (4.5
daN.m).
84
IMPORTANT
Before reconnecting the driver’s airbag cushion,
check to see if the system is operating correctly as
follows:
•check the airbag warning light on the
instrument panel is illuminated when the
ignition is on,
•connect a dummy ignition module to the
driver’s airbag connector and check that the
warning light extinguishes,
•switch the ignition off, connect the airbag
cushion in place of the dummy ignition module
and secure the cushion to the steering wheel,
•switch the ignition on. Check the warning light
illuminates for three seconds when the ignition
is switched on then extinguishes and remains
extinguished.
If the warning light does not operate exactly as
described above, refer to the fault finding section
and test the system using the XRBAG (Elé. 1288)
(see section 88).
IMPORTANT: if these instructions are not obser-
ved, the systems may not operate normally and
may be incorrectly triggered.
84-5

CONTROLS - SIGNALS
Ignition switch
REMOVAL - REFITTING
Disconnect the battery.
Set the wheels straight.
Remove:
- the half cowlings,
- the radio or glovebox (depending on equip-
ment),
- the immobiliser antenna ring or plastic sur-
round from the ignition switch (depending on
equipment).
Disconnect the ignition switch connectors (F).
84
Remove bolt (G) from the ignition switch.
Position the ignition key in position 3 and tilt re-
taining lugs (H) while releasing the switch.
DI8404
13068R
84-6

WIPERS
Front windscreen wiper
REMOVAL OF THE WIPER MECHANISM WITH
MOTOR
Make sure that the wiper motor is in the park
position.
Disconnect the battery.
Note the position of the wiper arms.
Open the bonnet.
Remove:
- the wiper arms using tool Elé. 1294-01,
- the scuttle panel grille seal,
- the scuttle panel grille after removing the two
side covers and the two bolts and disconnecting
the washer pipe.
85
13069R
Remove the three mechanism mounting bolts (A).
Disconnect the motor and release the assembly.
SPECIAL TOOLING REQUIRED
Elé. 1294-01 Wiper arm removing tool
Special notes for refitting
Check that the motor is in the park position be-
fore refitting the wiper arms.
Clean the splines on the wiper arm pins using a
metal brush.
Refit the wiper arms, locating the blade on the
marks made on removal.
Fit new nuts and torque tighten to 1.8 daN.m (±
15 %) using a torque wrench.
85-1

WIPERS
Front windscreen wiper
85
13069R1
Remove:
- the motor shaft nut (B) and release the linkage
after noting its position,
- the three motor mountings.
Release the motor after disconnecting it.
Special notes for refitting
Refit the linkage to the motor on the mark made
during removal.
Check that the motor is in the park position be-
fore refitting the wiper arms.
Clean the splines on the wiper arm pins using a
metal brush.
Refit the wiper arms, locating the blade on the
marks made on removal.
Fit new nuts and torque tighten to 1.8 daN.m (±
15 %) using a torque wrench.REMOVING THE MOTOR ALONE
Make sure that the wiper motor is in the park po-
sition.
Disconnect the battery.
Note the position of the wiper arms.
Open the bonnet.
Remove:
- the wiper arms using tool Elé. 1294-01,
- the scuttle panel grille seal,
- the scuttle panel grille after removing the two
side covers and the two bolts and disconnecting
the washer pipe.
85-2