1997 RENAULT KANGOO light

[x] Cancel search: light

clutch brake sensor automatic transmission fluid check transmission fluid four wheel drive horn

Page 19 of 83

RENAULT KANGOO 1997 KC / 1.G Electrical Equipment Workshop Manual 5.Connect the XR25, setting the ISO selector to
S8.
Enter code
Bargraphs
19 RH and 19 LH must be illumina-
ted (programming not carried out).
6. With one of the keys switch the ignition on
for appro

5.Connect the XR25, setting the ISO selector to
S8.
Enter code
Bargraphs
19 RH and 19 LH must be illumina-
ted (programming not carried out).
6. With one of the keys switch the ignition on
for approximately 2 seconds (without star-
ting the engine). Bargraph 18
LH illuminates
and bargraph
19 LH extinguishes.
The red immobiliser warning light flashes rapi-
dly.
7.Switch the ignition off and start command
G60* to lock the programming.
- the red immobiliser warning light should
flash (slow flashing)
- bargraphs 19 RH and 18 LH should be ex-
tinguished.
8.Switch the ignition on for a few seconds,
check that the red immobiliser warning light
is illuminated permanently (diesel) or that
the injection warning light is flashing (pe-
trol).
9.Switch the ignition on for more than 10
consecutive seconds.
10.Switch the ignition off and wait for the red
immobiliser warning light to flash slowly.
Enter command
with the ignition still off (bargraph
9 LH illu-
minates).
Switch the ignition on, the red immobiliser
warning light flashes more rapidly.
Follow the procedure for entering the securi-
ty code (see procedure for entering the secu-
rity code), using the code number correspon-
ding to the old kit. This erases the old code
memorised in the injection computer or the
coded solenoid valve.
IMMOBILISER
Coded key immobiliser system
REPLACING A KIT
(decoder unit plus two key heads)
If a kit is replaced it will be necessary to:
- programme the codes of the 2 new keys in the
new decoder unit (supplied uncoded).
- erase the old code in the injection computer or
coded solenoid valve using the security proce-
dure (the code number for the old kit should be
requested from the local assistance network,
example Delta Assistance for France, NVSR for
the UK by fax only)
IMPORTANT : to erase the old code (memorised in
the injection computer or coded solenoid valve
electronic unit), the procedure described below
must be followed in the correct order.
The code in the injection computer or coded sole-
noid valve cannot be erased with the security code
(using the number for the old kit) unless the deco-
der unit fitted to the vehicle has been program-
med with a different code (which is the case in the
following procedure).
NOTE : if the security code is entered when the
decoder unit has the same code as the injection
computer, or coded solenoid valve, it will not be
decoded.
1.Fit the metal inserts from the old keys into
the new key heads.
2.Note the number of one of the old keys to
obtain the security code number.
3.Remove the decoder unit with the ignition
off.
4.Fit the new decoder unit, ignition off.
82
G04*
D56
82-8

Page 20 of 83

RENAULT KANGOO 1997 KC / 1.G Electrical Equipment Workshop Manual 11. Switch the ignition off and on again for a few
seconds without starting the engine to pro-
gramme the immobiliser code for the new kit
in the injection computer or coded solenoid
valve. The red wa

Page 21 of 83

RENAULT KANGOO 1997 KC / 1.G Electrical Equipment Workshop Manual REPLACING THE INJECTION COMPUTER OR
CODED SOLENOID VALVE
The injection computer and coded solenoid valve
are supplied uncoded. The engine immobiliser
code must be programmed in when they are fit-
ted

Page 23 of 83

RENAULT KANGOO 1997 KC / 1.G Electrical Equipment Workshop Manual NOTE : this fault may be shown by the XR25 (in
injection fault finding).
Connect the XR25 and enter the injection code.
The fault is shown by bargraph 2 RH side.
After entering
the message
on the XR2

NOTE : this fault may be shown by the XR25 (in
injection fault finding).
Connect the XR25 and enter the injection code.
The fault is shown by bargraph 2 RH side.
After entering
the message
on the XR25 display indicates a fault on the coded
line.
Diesel vehicle
If a system fault is detected by the decoder unit
when the engine is running, the red immobiliser
warning light will illuminate permanently until
the ignition is switched off.
IMPORTANT: In this case, after repair, the fault
memorised in the decoder unit must be erased by
entering command
on the XR25 to allow the engine immobiliser sys-
tem to operate again.
NOTE: this fault may be shown by the XR25 using
fault finding for the decoder unit (fiche no. 56).
Connect the XR25.
Set the ISO selector to S8.
Enter code
The fault may be shown by bargraph
6 RH or LH
side. Switch the ignition on, the red engine immobiliser
warning light will flash (rapid flashing).
Enter the vehicle security code (number corre-
sponding to the original key number).
After entering the security code, the red warning
light will flash again.
The XR25 display should show
(in injection fault finding). This indicates that the
injection computer has been decoded.
Switch the ignition off, remove the decoded
computer and return it to stock.
Refit the computer and decoder unit to the vehi-
cle.
NOTE : When testing the injection using the XR25
on a vehicle without an immobiliser, bargraph 2
RH side will illuminate (*22 = 2 def = computer
not coded). This is normal.
SYSTEM FAULT, ENGINE RUNNING
Petrol vehicle
If a fault in the system is noted by the injection
computer when the engine is running, the injec-
tion warning light on the instrument panel will
flash during deceleration and at idle speed (en-
gine speed less than 1500 rpm).
IMPORTANT: In this case, after repair, the fault
memorised in the injection computer and the de-
coder unit must be erased by entering command
on the XR25 or by disconnecting the battery (ap-
proximately 30 seconds) to allow the engine im-
mobiliser system to operate again.
IMMOBILISER
Coded key immobiliser system
82
*22
D56G0**
G0**
82-12

Page 24 of 83

RENAULT KANGOO 1997 KC / 1.G Electrical Equipment Workshop Manual 4.Enter mode
on the XR25 then the security code number
and validate using
-If the code is correct
is displayed.
Bargraph 10 LH extinguishes.
The engine may be started.
The vehicle is protected once m

4.Enter mode
on the XR25 then the security code number
and validate using
-If the code is correct
is displayed.
Bargraph 10 LH extinguishes.
The engine may be started.
The vehicle is protected once more :
• approximately 10 minutes after switching
the ignition off (automatically),
• after disconnecting the battery.
-If the code is incorrect
is displayed.
Bargraph 10 LH remains illuminated.
The engine may not be started.
The red immobiliser warning light and the in-
jection warning light (depending on version)
flash.
Switch the ignition off, then repeat the proce-
dure for entering the code.
IMPORTANT: you may make 3 attempts to enter
the code. If, after the third attempt, the code is in-
valid, you must wait for approximately 15 mi-
nutes before making another attempt.
When this period has expired, switch the ignition
off and on again and 3 more attempts may be
made.
NOTE : This procedure does not decode the injec-
tion computer or coded solenoid valve (depen-
ding on the type of engine)- it only authorises the
starting of the vehicle.
REMINDER : The ignition must be switched off
and on again between attempts to enter the
code.
IMMOBILISER
Coded key immobiliser system
82
G40*
*
PROCEDURE FOR ENTERING THE SECURITY CODE
With this immobiliser system, the procedure for
entering the security code is managed by the de-
coder unit.
The code is entered using the XR25 only.
The security code can only be entered if the en-
gine immobiliser system is active. The red immobi-
liser warning light must flash when the ignition is
switched on (rapid flashing).
After determining the security code number (re-
quest from the local assistance network, example
DELTA Assistance for France, NVSR for the UK by
fax only) , carry out the following operations:
1.Ignition off, the red engine immobiliser war-
ning light should flash (slow flashing).
2.Switch the ignition on, the injection warning
light (petrol vehicle) illuminates for approxi-
mately 3 seconds then extinguishes, while the
red immobiliser warning light should flash
more quickly.
3.Connect the XR25 to the vehicle and set the
ISO selector on S8.
Enter code
Bargraph 10 LH should be illuminated (fault
finding fiche n° 56).
D56
82-13

Page 25 of 83

RENAULT KANGOO 1997 KC / 1.G Electrical Equipment Workshop Manual IMMOBILISER
Coded key immobiliser system
82
13063R
Track Allocation
A1 Courtesy light timer*
A2 Antenna ring coded connection
A3 Diagnostic socket information (line K)
A4 Diagnostic socket information

Page 27 of 83

RENAULT KANGOO 1997 KC / 1.G Electrical Equipment Workshop Manual IMMOBILISER
Coded key immobiliser system
82
KEY
104 Ignition switch
120 Injection computer
123 Door locking button
138 Rear right door locking motor
140 Driver’s door locking motor
141 Passenger’s

Page 32 of 83

RENAULT KANGOO 1997 KC / 1.G Electrical Equipment Workshop Manual INSTRUMENT PANEL
Dashboard
83
- the loud speaker grilles,
- the dashboard mountings.
Gently pull the dashboard.
Release the wiring retaining clips.
Disconnect:
- the headlight remote adjustment contro

Load next 8 pages

Page: < prev 1-8 9-16 17-24 25-32 33-40 41-48 49-56 ... 56 next >

lock fuel type four wheel drive water pump ABS horn