1997 RENAULT KANGOO light

CONTROLS - SIGNALS
Rotary switch under steering wheel
Special notes for refitting
Ensure the wheels are still straight.
Ensure the rotary switch under the steering wheel
is still immobilised before refitting.
If there is any doubt follow the method for cen-
tring described in section 88 "driver’s airbag".
Renew the steering wheel bolt each time it is re-
moved (pre-bonded bolt).
Observe the correct tightening torque (4.5
daN.m).
84
IMPORTANT
Before reconnecting the driver’s airbag cushion,
check to see if the system is operating correctly as
follows:
•check the airbag warning light on the
instrument panel is illuminated when the
ignition is on,
•connect a dummy ignition module to the
driver’s airbag connector and check that the
warning light extinguishes,
•switch the ignition off, connect the airbag
cushion in place of the dummy ignition module
and secure the cushion to the steering wheel,
•switch the ignition on. Check the warning light
illuminates for three seconds when the ignition
is switched on then extinguishes and remains
extinguished.
If the warning light does not operate exactly as
described above, refer to the fault finding section
and test the system using the XRBAG (Elé. 1288)
(see section 88).
IMPORTANT: if these instructions are not obser-
ved, the systems may not operate normally and
may be incorrectly triggered.
84-5

ELECTRICAL ASSISTANCE EQUIPMENT
Relay plate
POSITION AND ALLOCATION
(Most complete plate)
87
12965R
The relays are located above the fuse board at the
bottom of the dashboard. To reach them, open
the fuse box cover.
1 Lights on reminder buzzer
2 Front wiper timer
3 Flasher unit
4 Rear wiper timer
5 Heated rear screen relay
6 After ignition relay (electric window feed)
7 Front fog lights relay
87-1

ELECTRICAL ASSISTANCE EQUIPMENT
Relay plate
87
LIGHTS ON REMINDER BUZZER
Track Allocation
C + after ignition feed
E Door switch
L + side lights
95182R4
CONNECTION
NOTE : The track numbers are as for the compo-
nent.
FRONT WIPER TIMER
95182R2
Track Allocation
1 + timer
2 Earth
4 Wiper control
5 Wiper park
6 + after ignition feed
8 + washer pump
CONNECTION
NOTE : The track numbers are as for the compo-
nent.
8
5
2 1 46E
CL
87-2

ELECTRICAL ASSISTANCE EQUIPMENT
Relay plate
87
FRONT FOG LIGHTS RELAY
Track Allocation
85 + relay control
86 Earth
30 + before ignition feed
87a Not used
87 Front fog lights
13058R
CONNECTION
NOTE : The track numbers are as for the compo-
nent.
87-5

WIRING
Heated rear screen
88
77324S
REPAIR
Using a small brush proceed to carry out the re-
pair, applying a sufficiently thick coat. Where suc-
cessive coats are applied allow drying time bet-
ween each coat. Do not repeat the operation
more than three times.
However, if there is a run it will be possible to eli-
minate it using the point of a knife or razor blade
once the product is sufficiently hardened (after se-
veral hours).
The adhesive tape acting as a guide must not be
removed for one hour after application. The tape
must be torn off perpendicularly to the resistance
in the direction of the arrow. The varnish, applied
at an ambient temperature of 20
oC, is completely
dry in three hours. At a lower temperature the
drying time should be slightly increased.
88-2

WIRING
Remote control for door locking
88
.GENERAL
These vehicles are equipped with an infrared or
radio frequency remote control with rolling code,
which prevents the code from being copied.
When a transmitter is replaced it will therefore be
necessary to resynchronise it so that the transmit-
ters are returned to phase with the decoder unit.
This remote control is only used for locking and
unlocking the opening elements (it has no effect
on the immobiliser).
IMPORTANT: this system cannot operate with
three remote controls (the decoder unit can only
manage two different rolling codes).
THE TRANSMITTER (PLIP)
Replacing or adding a remote control with immo-
biliser function without replacing the decoder
unit.
Order a spare key head using the number in the
head of one of the old keys or the label normally
attached to the keys when the vehicle is delivered
(eight alphanumeric characters).
If a key is being added or has been lost, remember
to order the insert with the key number.
Carry out the special resynchronisation procedure
using the XR25.
This procedure resets the remote control into se-
quence with the decoder unit (rolling code) and
should only be used if the decoder unit is not
being replaced (with immobiliser only).
1.Ignition off, connect the XR25 (ISO selector on
S8, code D56).
For vehicles fitted with an infra-red remote
control, enter command mode G04* (forced
protection mode) then switch the ignition on
again and enter the vehicle’s security code
(see procedure in section 82).
For vehicles fitted with a radio frequency re-
mote control, go to point 2.
2.Switch the ignition off and enter command
mode G32*.
From this moment, the operator has 10 se-
conds to carry out the next operation.
NOTE: The 10 seconds are shown by the illu-
mination of the red immobiliser warning light
and bargraph 17 LH on the XR25
(code D56,
fiche n° 56).
3.Press the remote control twice (the doors lock
and unlock and the red warning light extin-
guishes).
NOTE :
- When replacing a key head, resynchronisa-
tion of the second remote control (if fitted)
is not always necessary.
Check that the second control operates,
otherwise resynchronise it.
- If both remote controls (if fitted) are desyn-
chronised, two resynchronisation proce-
dures will have to be carried out (one for
each remote control).
IMPORTANT: To ensure that the infrared code
is correctly transmitted it is essential to direct
the transmitter correctly towards the receiver.
If the procedure fails it will be necessary to
restart from the beginning (infrared remote
control only).
4.The procedure is complete - check that the
doors lock correctly.
88-3

WIRING
Remote control for door locking
88
Ignition off:
1.Press and hold the central door locking button
for a few seconds until the doors lock and un-
lock.
From this moment, the operator has 10 se-
conds to carry out the next operation.
NOTE: The 10 seconds are shown by the illu-
mination of the red immobiliser warning light
(if fitted) and bargraph 17 LH on the XR25
(code
D56, fiche n° 56).
2.Press the remote control twice (the doors lock
and unlock and the red warning light extin-
guishes, if fitted).
NOTE : If both remote controls (if fitted) are
desynchronised, two resynchronisation proce-
dures will have to be carried out (one for each
remote control).
IMPORTANT: To ensure that the infrared code
is correctly transmitted it is essential to direct
the transmitter correctly towards the receiver.
If the procedure fails it will be necessary to
restart from the beginning (infrared remote
control only).
3.The procedure is complete - check that the
doors lock correctly.
Removal - Refitting
The dashboard must be partially removed to re-
move the decoder unit.
Remove:
- the steering wheel with the wheels straight,
- the half cowlings under the steering wheel,
- the knee protector under the steering column,
- the lights and wiper controls,
- the instrument panel surround,
- the instrument panel,
- the ashtray, its mounting and the two dash-
board mounting bolts on the heating unit,
- the trim at the bottom of the dashboard on the
driver’s side,
- the two speaker grilles on the dashboard,
- the dashboard mountings.
THE DECODER UNIT
The decoder unit is located in the left hand side of
the dashboard (A).
12967R
88-5

WIRING
Remote control for door locking
88
REMOTE CONTROL RECEIVER
This is located near to the courtesy light.
It receives the remote control code and transmits
it to the decoder unit. Its function is to amplify the
signal.
The remote control receiver is replaced indepen-
dently of the transmitter and the decoder unit (it
is not coded).
Removal - Refitting
Remove:
- the light diffuser, lifting it with a small screw-
driver at points (A),
13073R
13065R
Replacement
For vehicles fitted with an immobiliser, refer to
section 82 (programming procedure). The decoder
unit is common to the immobiliser.
For vehicles without an immobiliser, carry out a
resynchronisation operation.
NOTE : Fault finding for the remote control sys-
tem may be carried out using the XR25 (fault fin-
ding fiche n° 56).
Move the dashboard as far back as possible, dis-
connect the decoder unit and remove the two
mounting bolts (B) using a small ratchet fitted
with a Torx 20 socket.
88-6