1997 MITSUBISHI TRITON transmission

FRONT AXLE ± General Information26-2
GENERAL INFORMATION26100010111
2WD
The front hub assembly which uses a double taper
roller bearing is mounted on the knuckle spindle.For vehicles with ABS, a rotor for detecting the
wheel speed is press-fitted into the front hub.
4WD
The front axle consists of the hub assembly, drive
shaft, inner shaft, front differential, freewheel clutch
assembly and actuator. The features are:

The wheel bearing uses a double taper roller
bearing. For vehicles with ABS, a rotor for
detecting the wheel speed is bolted to the brake
disc.

Drive shafts of almost identical length reduce
torque steer. In addition, a D.O.J.-B.J.-type
constant velocity ball joint has high power
transmission efficiency and reduces vibration
and noise.
A vacuum-type freewheel clutch has been
adopted in the freewheel mechanism. Its
solenoid valve and actuator switch powertrain
between 2WD and 4WD.

There are two types of differential gear. The
difference between them is gear ratio.
2WD
ItemSpecifications
Wheel bearingTypeDouble taper roller bearing
Inner bearing (O.D. x I.D.) mm65.1 x 34.9
Outer bearing (O.D. x I.D.) mm50.0 x 21.4
4WD

ItemSpecifications
Wheel bearingTypeDouble taper roller bearing
Inner bearing (O.D. x I.D.) mm73 x 45
Outer bearing (O.D. x I.D.) mm73 x 45
Drive shaftJoint typeOuter: B.J.
Inner: D.O.J.
Shaft length (joint to joint) mmRight: 318
Left: 291
Inner shaftO.D. x length mm31.5 x 304.2
Bearing (O.D. x I.D.) mm62 x 35

4
GROUP 00
GENERAL
VEHICLE IDENTIFICATION
MODELS
Model Code Engine model Transmission model Fuel supply sys-
tem
JERDEL6 R4AW2 (2WD-4A/TK62T
ENDEL64G63-SOHC (1,997m
ℓ )
R5M21 (2WD-5M/T)MPI
ENDL6
ENDR6
CENDL6
K64T
JENDL64D56 (2,477m
ℓ )
R5M21 (2WD-M/T) Fuel injection
CENDEL6K75T
GJENXEL64G64-SOHC (2,351 m
ℓ )
V5M21 (4WD-5M/T) MPI
ENDFL6
ENDFR6V5MT1 (4WD-5M/T
JERDFL6 V4AW2 (AWD-4A/T
GJERXFL6
GJENXFL6
GJENXFR6
CENDFL6
GCENXFL6
JENDFL6
JENDFR6
K74T
JENHFL64D56- Turbocharger with
intercooler (2,477m
ℓ )
V5MT1 (4WD-5M/TFuel injection
00-1GENERAL – vehicle identification

14
LUBRICANTS
Items Specified lubricant Quantity
Manual steering gear oil Hypoid gear oil API
GL-4 or higher SAE 80210 cm3 (12.81 cu.in.)
Power steering fluid
L.H. drive vehicles
<2800D>11.1 dm3 (1.17 U.S.qts.,
0.98 lmp.qts.)
1.06 dm3 (1.12 U.S.qts.,
0.93 lmp.qts.)
R.H. drive vehicels Automatic transmission fluid
DEXRON or DEXRON II
<2800D>1.02 dm3 (1,08 U.S.qts.,
0.90 lmp.qts.)
0.97 dm3 (1.02 U.S. qts.,
0.85 lmp.qts.)
Power steering gear box
Bearing, O-ring and oil seal
Automatic transmission fluid
DEXRON or DEXRON IIAs required
Oil pump
Flow control valve and O-ring
Friction surface of rotor, vane, cam ring
and pump coverAutomatic transmission fluid
DEXRON or DEXRON IIAs required
SEALANTS AND ADHESIVES
Items Specified sealant and adhesive Remarks
Steering column cover assembly
installation hole
Dash panel cover installed surface
Manual steering gear box top cover
packing
Manual steering gear box cross-shaft
adjusting and lock nut3M ATD Part No. 861 or equivalent Semi-drying sealant
Manual steering gear box top cover bolt
Manual steering gear box adjusting shim
Tie-rod end dust cover installed surface
Inside of steering column lower pipe
bearing
Connection of steering column upper and
steering column lower (Nut side)3M Stud Locking Part No. 4170 or
equivalentSemi-drying sealant
Steering column upper bearing 3M ATD Part No. 8001 or equivalent Semi-drying sealant
37-4STEERING – Specifications
E37CD--

E37CE--