1997 LINCOLN MARK VIII belt

44TroubleshootingIf the display shows the following message during
any of the compass adjustment procedures, contact
your dealer:If the compass always displays one direction while
turning a full 360-degree circle, perform the
Calibration Procedure.
A system of warning lights are located below the
Message Center. Warning lights are used to monitor
the operation of your vehicle.
Safety Belt Warning Light and ChimeThis warning light and chime remind you to fasten
your safety belt. The following conditions will take
place:q
If the driver's safety belt is not buckled when
the ignition is turned to the ON position, the
light will turn on for 1 to 2 minutes and the
chime will sound for 4 to 8 seconds.
q
If the driver's safety belt is buckled while the
light is on and the chime is sounding, the light
and the chime will turn off.
q
If the driver's safety belt is buckled before the
ignition is turned to the ON position, neither
the light nor the chime will turn on.
File:03fnis8.ex
Update:Thu Jun 27 10:00:37 1996

134The rotating boot on the lap belt is designed to
allow both rear seat entry/exit and access to the
front seat passengers. To enter the rear seat:
1. Rotate the safety belt boot rearward.
2. Enter the rear seat in front of the safety belt.
3. Rotate the safety belt boot forward to allow use
by the front seat passengers.Using the Power SeatsYour vehicle's power seats can be adjusted in
several directions. You can raise or lower the whole
seat, move the seat forward or backward and tilt
the front and back of the seat up or down.
The controls to operate the power seats are located
on the outside of each front seat.The power seat controls
Power Lumbar SupportWith this feature, you can position a lumbar
support pad in the seatback.
File:06fnss8.ex
Update:Wed Jun 19 15:04:39 1996

137
If the seatback is moved from its forward stop angle
while the seat is traveling forward, the seat will
stop. If the seatback is returned to the forward stop
angle position, the seat will resume its forward
travel. If the seatback is returned to its upright
position, the seat will return to the original position.
If the transmission is shifted from N (Neutral) or P
(Park) while the driver's seat is moving, the seat
will stop where it is. Returning the gearshift to N
(Neutral) or P (Park) will allow seat movement to
continue. To allow movement without returning to
P (Park) or N (Neutral) will require the use of the
electric seat controls.
If you sit in the seat while the Auto-Glide is
moving rearward, the seat will continue to move.
If the seat stalls, or if any seat switch is
momentarily activated (excluding the lumbar switch)
while the seat is traveling forward, the seat will
stop. If the seatback is returned to its upright
position, the seat will return to the position it wasat when the ease of entry cycle was started. To
resume forward travel will require moving the
seatback off of its forward stop angle position and
returning it back to the same. Repositioning the seat
at this time using the seat controls will cancel
Auto-Glide.
If the ignition is off, and the last open door is
closed while a seat is moving, 30 seconds will be
allowed for the forward or rearward movement to
be completed.
Easy Access/Easy Out (driver side
only)The easy in/easy out feature of the driver seat
moves the seat two inches back when:q
the transmission is in N (Neutral) or P (Park)
q
the driver safety belt is buckled
q
the ignition switch is turned to OFF.
File:06fnss8.ex
Update:Wed Jun 19 15:04:39 1996

138The easy in/easy out feature of the driver seat
moves the seat two inches forward when:q
the transmission is in N (Neutral) or P (Park)
q
the driver safety belt is buckled
q
the ignition switch is turned to ON.
Important Safety Belt InformationThe use of safety belts helps to restrain you and
your passengers in case of a collision. In most states
and in Canada, the law requires their use.
Safety belts provide best restraint when:q
the seatback is upright
q
the occupant is sitting upright (not slouched)
q
the lap belt is snug and low on the hips
q
the shoulder belt is snug against the chest
q
the knees are straight forward
To help you remember to fasten your safety belt, a
warning light may come on and a chime may
sound. SeeSafety Belt Warning Light and Chimein
theInstrumentationchapter.
See the following sections in this chapter for
directions on how to properly use these safety belts.
Also seeSafety Restraints for Childrenin this
chapter for special instructions about using safety
belts for children.
File:06fnss8.ex
Update:Wed Jun 19 15:04:39 1996

140
WARNING
Fordrecommend stha tal lsafet ybelt
WARNING
Childre nshoul dalway srid ewit hthe
WARNING
Neve rle ta passenge rhol dachil don
WARNING
Loc kthedoor sof you rvehicl ebefore

141
Fastening the combination lap and shoulder
belt
Fastening the rear seat lap and shoulder beltNOTE:Be sure to read and understandImportant
Safety Belt Informationin this chapter.
To adjust the lap part of the belt,pull up on the
shoulder belt until the lap belt fits snugly and as
low as possible around your hips.
File:06fnss8.ex
Update:Wed Jun 19 15:04:39 1996

142While the belt retracts, guide the tongue to its
original position to prevent it from striking you or
the vehicle.
Unfastening the lap/shoulder belts
Right Front or Rear Window Seating
PositionsYour vehicle is equipped with a dual locking mode
retractor on the shoulder belt portion of the
combination lap/shoulder safety belt for front seat
passenger and rear outboard passengers.
Dual locking mode retractors operate in two
ways:Vehicle sensitive (emergency) locking
modeIn this operating mode, the shoulder belt retractor
will allow the occupant freedom of movement,
locking tight only on hard braking, hard cornering
or impacts of approximately 5 mph (8 km/h) or
more. The retractor can also be made to lock by
pulling the belt out quickly.
File:06fnss8.ex
Update:Wed Jun 19 15:04:39 1996

144Unfastening the center rear lap safety beltNOTE:Be sure to read and understandImportant
Safety Belt Informationin this chapter.
Pull the belt across your hips and insert the tongue
into the correct buckle on your seat until you hear
a snap and feel it lock. Make sure the buckle is
securely fastened.
If you need to lengthen the belt, unfasten it and tip
the belt tongue at a right angle to the belt. Pull the
belt tongue over your lap until it reaches the
buckle.If you need to shorten the belt, pull on the loose
end of the webbing until the belt fits snugly.
To unfasten the belt, push the release button on
the buckle. This allows the tongue to unlatch from
the buckle.
Safety Belt Extension AssemblyFor some people, the safety belt may be too short
even when it is fully extended. You can add about
eight inches (20 cm) to the belt length with a
safety belt extension assembly (part number
611C22). Safety belt extensions are available at no
cost from your dealer.
Use only extensions manufactured by the same
supplier as the safety belt. Manufacturer
identification is located at the end of the webbing
on the label. Also, use the safety belt extension only
if the safety belt is too short for you when fully
extended. Do not use extension to change the fit of
the shoulder belt across the torso.
File:06fnss8.ex
Update:Wed Jun 19 15:04:39 1996