1997 Lexus GS300 change time

AIR CONDITIONING AND AUDIO
11 2(a) Listening to the radio
1. Push the
(A/M) or (F/M 1/2) button to
turn the radio on and select either an AM or FM broadcast.
ªAM,º ªFM1º or ªFM2º will appear on the display.
The radio can also be turned on by pushing the ªPWR.VOLº
knob if the radio was being used when the system was
turned off.
2. Tune the ªPWR.VOLº knob to adjust the volume.
3. Tune in the desired station. (See ª(b) Selecting a
station.º)
The radio will change automatically to stereo reception when
an FM stereo broadcast is being received. At the same time
ªSTº will appear on the display. When the receiving signal
gets weak, the channel separation will automatically be
reduced for lowest noise. If the signal becomes extremely
weak, the radio will switch over to monaural reception.
4. Adjust the tone and sound balance. (See ª(d) Adjusting
the toneº and ª(e) Adjusting the sound balance.º)
5. To turn the radio off, push the ªPWR.VOLº knob.(b) Selecting a station
Tune in the desired station using one of the following
methods. The frequency will appear on the display.
Preset tuning: Use for tuning±in to a desired preset station.
Push the station selector button to which the desired station
has been preset. The radio will tune in to the station and the
button number will appear on the display. See ª(c) Presetting
a station.º)
Seek tuning: Use for automatic station search and stop.
Push the
(SEEK) button and hold it until a beep is heard.
The radio will begin seeking up or down for a station of the
nearest frequency and will stop on reception. Each time you
push the button, stations will be searched out one after
another.
Scan tuning: Use for scanning preset stations or
station±to±station scanning.
Push the
(SCAN) button for less than 2 seconds. With
ªP. SCANº blinking on the display, the radio will automatically
seek out a preset station of a higher channel number in the
AM/FM mode. If there is a preset station on the channel,
then the tuning is held for 5 seconds. If there is no station
on the channel, then the tuning is only held for 1 second. If
the
(SCAN) button is pushed while listening to a preset
station channel, then the scan proceeds to the next highest
channel, proceeding in turn through the 6 channels of FM1
and then the 6 channels of FM2, then repeating the process.
To continue listening to the channel of your choice, simply
push the
(SCAN) button once again.

AIR CONDITIONING AND AUDIO
11 3 Push the
(SCAN) button for longer than 2 seconds.
With ªSCANº on the display, the radio will automatically seek
out a station of higher frequency, hold it for 5 seconds and
scan to the next. To continue listening to the broadcast of
your choice, simply push the
(SCAN) button once
again.
Manual tuning: Push the
(TUNE) button briefly. Each
time you push the button, the radio will step up or down to
another frequency.
(c) Presetting a station
1. Tune in the desired station. (See ª(b) Selecting a
station.º)
2. Push one of the station selector buttons and hold it until
a beep is heard. This sets the station to the button and the
button number will appear on the display.
Each button can store one AM station and two FM stations.
To change the preset station to a different one, follow the
same procedure.
The preset station will be cancelled when the power source
is cut off (battery disconnected, blown fuse, etc.).
(d) Adjusting the tone
To adjust the low±pitched tone, push the ªBASSº knob (if
depressed) and turn it.
To adjust the middle±pitched tone, push the ªMIDº knob (if
depressed) and turn it.
To adjust the high±pitched tone, push the ªTREBLEº knob (if
depressed) and turn it.(e) Adjusting the sounds balance
To balance the sound between the right and left speakers,
push the ªBALANCEº knob (if depressed) and turn it.
To balance the sound between the front and rear speakers,
push the ªFADERº knob (if depressed) and turn it.
Radio operating tips
The antenna automatically extends when the radio and
ignition are turned on and retracts when either is turned off.
CAUTION!
Before extending the antenna, confirm that no one
is close enough to get injured.
NOTICE
To prevent damage to the antenna, make sure it is
retracted before running your vehicle through an
automatic car wash.

AIR CONDITIONING AND AUDIO
127
Once the system is set, the indicator light turns on and off
with the ignition switch in ªOFFº and ªSECº will appear each
time the key is turned to the ªACCº position.
To change the identification number for some reason, cancel
the system (See ª(b) Cancelling the anti±theft system.º) and
set it again with a new number.
The system will be activated if the electrical power source is
disconnected from the radio unit. When the system is
activated, the audio system cannot be turned on even after
the power supply resumes and ªSECº will appear on the
display. If this happens, such as when the battery is
discharged, see ª(c) If the anti±theft system is activated.º(b) Cancelling the anti±theft system
1. Follow steps 1 to 4 described in ª(a) Setting the
anti±theft system.º
2. With your identification number appearing on the
display, press the
(SCAN) button and hold it in until
ª±±±º appears on the display. ª±±±º will go off to indicate the
system is cancelled. If invalid buttons have been used, ªErrº
will appear on the display and ªSECº appears. Try again
from step 3 in ª(a) Setting the anti±theft system.º
The number displayed with ªErrº indicates how many errors
you have made. You may make up to nine errors, but no
more!