1997 JAGUAR XJ6 tire size

Inspection
8Clean and dry the pump body and both
rotors. Measure the outside diameter of the
outer rotor and thickness of both rotors.
9Place the outer rotor into the pump body
and use feeler gauges to measure the
clearance between the outer rotor and the
body (see illustration).
10Place a straightedge across the pump
body and measure between the straightedge
and the rotors to check the over-the-rotor
clearance (see illustration). Compare your
measurements to this Chapter’s Specifications
and renew the oil pump if any are beyond the
maximum allowable.
11Remove the oil pressure relief valve cap.
Remove and clean the relief valve components
(see illustration).
12Clean all components with solvent and
inspect them for wear and damage. If
excessive wear, damage or if any clearance is
beyond the Specifications, renew the entire
pump as an assembly.
13Check the oil pressure relief valve piston
sliding surface and valve spring. If either the
spring or the valve is damaged, they must be
renewed as a set.
Refitting
14Lubricate the drive and driven rotors with
clean engine oil and place them in the casewith the marks facing out. Apply a thin coat
of anaerobic sealant (Loctite 510 or 518) to
the gasket flange and refit the cover (see
illustration).
15Lubricate the oil pressure relief valve
piston with clean engine oil and refit the valve
components into the oil pump body (see
illustration 13.11).
16Apply a thin coat of anaerobic sealant
(Loctite 510 or 518) to the oil pump-to-engine
block-mounting surface, position the oil pump
body against the engine block and refit the
mounting bolts, tightening the bolts to the
torque listed in this Chapter’s Specifications.
Follow a criss-cross pattern when tightening
the bolts to avoid warping the oil pump body.
17If using the original oil pump, refit the
original sprocket shim pack (see illustration).
If a new pump is installed, start off with a
0.38 mm (0.015-inch) thick shim pack, refit the
drive sprocket and align the sprocket as
follows.
18Use a straightedge to check the alignment
of the oil pump sprocket with the crankshaft
sprocket (see illustration). If they are not
aligned, increase or decrease the shim pack at
the oil pump sprocket until alignment is correct,
then secure the oil pump sprocket bolts by
bending up the sheetmetal tabs. Note:You
may be able to use all or part of the original
shim pack from the original oil pump (if a new
pump is being fitted). If required, shims areavailable in 0.127 mm (0.005 inch), 0.254 mm
(0.010 inch) and 0.508 mm (0.020 inch) sizes.
19Fit new O-rings to each end of the transfer
tubes and refit the tubes into the transfer
housing. Note:Use petroleum jelly to lubricate
the O-rings.
20Apply a thin coat of RTV sealant to the
engine block-mounting surface of the transfer
housing. Lift the transfer housing and tubes
into place and push the front of the tubes
in the back of the oil pump, until you can start
the transfer housing-to-engine block bolts.
Tighten the bolts to the torque listed in this
Chapter’s Specifications.
21Refit the remaining parts in the reverse
order of removal.
22Add oil, start the engine and check for oil
pressure and leaks.
23Recheck the engine oil level.
14 Driveplate-
removal and refitting
4
Removal
1Raise the car and support it securely on
axle stands, then refer to Chapter 7 and
remove the transmission. If it’s leaking, now
would be a very good time to renew the front
pump seal/O-ring.
2A•16 Engine in-car repair procedures
13.9 Measure the outer rotor-to-body
clearance with feeler gauges (arrowed)13.10 With a straightedge held tight to the
pump surface, measure the clearance over
the rotors with feeler gauges13.11 Oil pressure relief valve components
A Relief valve cap
B TubeC Spring
D Valve
13.14 Apply a thin coat anaerobic sealant
(Loctite 510 or 518) to the pump cover
sealing surface
13.17 Refit the original shim pack
(arrowed) if the original pump is being
used - if a new pump is being installed,
refit a 0.38 mm (0.015-inch) shim pack
3261 Jaguar XJ6
13.18 Check the oil pump and crankshaft
sprocket alignment with a straightedge -
add or subtract shims until the sprockets
are aligned for smooth chain operation

is the difference between the parallel and
perpendicular readings. Compare your results
to this Chapter’s Specifications.
8If the cylinder walls are badly scuffed or
scored, or if they’re out-of-round or tapered
beyond the limits given in this Chapter’s
Specifications, have the engine block rebored
and honed at an automotive machine
workshop. If a rebore is done, oversize
pistons and rings will be required.
9Using a precision straightedge and feeler
gauge, check the engine block deck (the
surface that mates with the cylinder head) for
distortion (see illustration 10.13). If it’s
distorted beyond the specified limit, it can be
resurfaced by an automotive machine
workshop.
10If the cylinders are in reasonably good
condition and not worn to the outside of the
limits, and if the piston-to-cylinder clearances
can be maintained properly, then they don’t
have to be rebored. Honing is all that’s
necessary (refer to Section 17).
17 Cylinder honing
3
1Prior to engine reassembly, the cylinder
bores must be honed so the new piston rings
will seat correctly and provide the best
possible combustion chamber seal. Note:If
you don’t have the tools or don’t want to
tackle the honing operation, most automotive
machine shops will do it for a reasonable fee.
2Before honing the cylinders, refit the main
bearing caps (without bearing inserts) and
tighten the bolts to the specified torque.
3Two types of cylinder hones are commonly
available - the flex hone or “bottle brush” type
and the more traditional surfacing hone with
spring-loaded stones. Both will do the job, but
for the less-experienced mechanic the “bottle
brush” hone will probably be easier to use.
You’ll also need some paraffin or honing oil,
rags and a variable-speed electric drill motor.
The drill motor should be operated at a
steady, slow speed. Proceed as follows:
a) Mount the hone in the drill motor,
compress the stones and slip it into the
first cylinder (see illustration).
Warning: Be sure to wear safety
goggles or a face shield!
b) Lubricate the cylinder with plenty of
honing oil, turn on the drill and move the
hone up-and-down in the cylinder at a
pace that will produce a fine crosshatch
pattern on the cylinder walls. Ideally, the
crosshatch lines should intersect at
approximately a 60° angle (see
illustration). Be sure to use plenty of
lubricant and don’t take off any more
material than is absolutely necessary to
produce the desired finish. Note:Piston
ring manufacturers may specify a smallercrosshatch angle than the traditional 60° -
read and follow any instructions included
with the new rings.
c) Don’t withdraw the hone from the cylinder
while it’s running. Instead, shut off the drill
and continue moving the hone up-and-
down in the cylinder until it comes to a
complete stop, then compress the stones
and withdraw the hone. If you’re using a
“bottle brush” type hone, stop the drill
motor, then turn the chuck in the normal
direction of rotation while withdrawing the
hone from the cylinder.
d) Wipe the oil out of the cylinder and repeat
the procedure for the remaining cylinders.
4After the honing job is complete, chamfer
the top edges of the cylinder bores with a
small file so the rings won’t catch when the
pistons are installed. Be very careful not to
nick the cylinder walls with the end of the file.
5The entire engine block must be washed
again very thoroughly with warm, soapy water
to remove all traces of the abrasive grit
produced during the honing operation. Note:
The bores can be considered clean when a
lint-free white cloth - dampened with clean
engine oil - used to wipe them out doesn’t
pick up any more honing residue, which will
show up as grey areas on the cloth. Be sure to
run a brush through all oil holes and galleries
and flush them with running water.
6After rinsing, dry the engine block and
apply a coat of light rust preventive oil to all
machined surfaces. Wrap the engine block in
a plastic bag to keep it clean and set it aside
until reassembly.
18 Pistons/connecting rods-
inspection
2
1Before the inspection process can be
carried out, the piston/connecting rod
assemblies must be cleaned and the original
piston rings removed from the pistons. Note:
Always use new piston rings when the engine
is reassembled.
2Using a piston ring refitting tool, carefully
remove the rings from the pistons. Be careful
not to nick or gouge the pistons in the
process.
3Scrape all traces of carbon from the top of
the piston. A hand-held wire brush or a piece
of fine emery cloth can be used once the
majority of the deposits have been scraped
away. Do not, under any circumstances, use a
wire brush mounted in a drill motor to remove
deposits from the pistons. The piston material
is soft and may be eroded away by the wire
brush.
4Use a piston ring groove-cleaning tool to
remove carbon deposits from the ring
grooves. If a tool isn’t available, a piece
broken off the old ring will do the job. Be very
careful to remove only the carbon deposits -
don’t remove any metal and do not nick or
scratch the sides of the ring grooves (see
illustrations).
5Once the deposits have been removed,
clean the piston/connecting rod assemblies
with solvent and dry them with compressed
air (if available). Make sure the oil return holes
2B•12 Engine removal and overhaul procedures
17.3a A “bottle brush” hone will produce
better results if you have never done
cylinder honing before17.3b The cylinder hone should leave a
smooth, crosshatch pattern with the lines
intersecting at approximately a 60° angle
18.4a The piston ring grooves can be
cleaned with a special tool, as shown . . .18.4b . . . or a section of a broken ring
3261 Jaguar XJ6

connecting rods. Apply a light coat of oil to
the bolt threads and the under sides of the
bolt heads, then refit them. Tighten all main
bearing cap bolts to the torque listed in this
Chapter’s Specifications, starting in the centre
and working out to the ends.
21Rotate the crankshaft a number of times
by hand to check for any obvious binding.
22Check the crankshaft endplay with a
feeler gauge or a dial indicator as described in
Section 14. The endplay should be correct if
the crankshaft thrust faces aren’t worn or
damaged and new thrust washers have been
installed. Note:If the end-play is too great,
even with the new thrust bearings, oversized
thrust bearings are available. There are two
sizes, 0.005-inch and 0.010-inch oversize.
23Refit a new rear main oil seal, then bolt the
retainer to the engine block (see Section 24).
24 Rear main oil seal refitting
2
1The crankshaft must be installed first and
the main bearing caps bolted in place, then
the new seal should be installed in the retainer
and the retainer bolted to the engine block.
2Check the seal contact surface on the
crankshaft very carefully for scratches and
nicks that could damage the new seal lip and
cause oil leaks. If the crankshaft is damaged,
the only alternative is a new or different
crankshaft.
3Refer to Part A of this Chapter for refitting
of the new rear seal, using the plastic
alignment tool supplied with the engine
overhaul gasket set.
25 Pistons/connecting rods-
refitting and big-end bearing
oil clearance check
3
1Before refitting the piston/connecting rod
assemblies, the cylinder walls must be
perfectly clean, the top edge of each cylinder
must be chamfered, and the crankshaft must
be in place.
2Remove the cap from the end of the
number one connecting rod (refer to the
marks made during removal). Remove the
original bearing inserts and wipe the bearing
surfaces of the connecting rod and cap with a
clean, lint-free cloth. They must be kept
spotlessly clean.
Big-end bearing
oil clearance check
3Clean the back side of the new upper
bearing insert, then lay it in place in the
connecting rod. Make sure the tab on the
bearing fits into the recess in the rod so the oil
holes line up. Don’t hammer the bearing insert
into place and be very careful not to nick or
gouge the bearing face. Don’t lubricate the
bearing at this time.4Clean the back side of the other bearing
insert and refit it in the rod cap. Again, make
sure the tab on the bearing fits into the recess
in the cap, and don’t apply any lubricant. It’s
critically important that the mating surfaces of
the bearing and connecting rod are perfectly
clean and oil free when they’re assembled.
5Position the piston ring gaps at staggered
intervals around the piston (see illustration).
6Slip a section of plastic or rubber hose over
each connecting rod cap bolt.
7Lubricate the piston and rings with clean
engine oil and attach a piston ring compressor
to the piston. Leave the skirt protruding about
1/4-inch to guide the piston into the cylinder.
The rings must be compressed until they’re
flush with the piston.
8Rotate the crankshaft until the number one
connecting rod journal is at BDC (bottom
dead centre) and apply a coat of engine oil to
the cylinder wall.
9With the word FRONT (or the arrow) on top
of the piston facing the front of the engine
(see illustration), gently insert the piston/
connecting rod assembly into the number one
cylinder bore and rest the bottom edge of the
ring compressor on the engine block.
10Tap the top edge of the ring compressor
to make sure it’s contacting the engine block
around its entire circumference.11Gently tap on the top of the piston with
the end of a wooden hammer handle (see
illustration) while guiding the end of the
connecting rod into place on the crankshaft
journal. The piston rings may try to pop out of
the ring compressor just before entering the
cylinder bore, so keep some downward
pressure on the ring compressor. Work
slowly, and if any resistance is felt as the
piston enters the cylinder, stop immediately.
Find out what’s hanging up and fix it before
proceeding.
Caution: Do not, for any reason, force the
piston into the cylinder - you might break a
ring and/or the piston.
12Once the piston/connecting rod assembly
is installed, the big-end bearing oil clearance
must be checked before the rod cap is
permanently bolted in place.
13Cut a piece of the appropriate size
Plastigauge slightly shorter than the width of
the big-end bearing and lay it in place on the
number one connecting rod journal, parallel
with the journal axis (see illustration).
14Clean the connecting rod cap bearing
face, remove the protective hoses from the
connecting rod bolts and refit the rod cap.
Make sure the mating mark on the cap is on
the same side as the mark on the connecting
rod. Check the cap to make sure the front
mark is facing the timing chain of the engine.
15Apply a light coat of oil to the under sides
of the nuts, then refit and tighten them to the
torque listed in this Chapter’s Specifications,
Engine removal and overhaul procedures 2B•17
2B
25.13 Lay the Plastigauge strips on each
big-end bearing journal, parallel to the
crankshaft centreline
3261 Jaguar XJ6
25.5 Stagger the ring end gaps around the
piston as shown25.9 Pistons must be installed with the
arrow (right arrow) or FRONT facing the
front of the engine - left arrow indicates
piston size letter
25.11 The piston can be driven (gently)
into the cylinder bore with the end of a
wooden or plastic hammer handle
A Oil ring rail gaps
B Second compression ring gap
C Oil ring spacer gap
D Top compression ring gap

working up to it in three steps. Note:Use the
old bolts for this step (save the new bolts for
final refitting).Use a thin-wall socket to avoid
erroneous torque readings that can result if
the socket is wedged between the rod cap
and nut. If the socket tends to wedge itself
between the nut and the cap, lift up on it
slightly until it no longer contacts the cap. Do
not rotate the crankshaft at any time during
this operation.
16Remove the nuts and detach the rod cap,
being careful not to disturb the Plastigauge.
17Compare the width of the crushed
Plastigauge to the scale printed on the
envelope to obtain the oil clearance (see
illustration). Compare it to this Chapter’s
Specifications to make sure the clearance is
correct.
18If the clearance is not as specified, the
bearing inserts may be the wrong size (which
means different ones will be required). Before
deciding that different inserts are needed,
make sure that no dirt or oil was between the
bearing inserts and the connecting rod or cap
when the clearance was measured. Also,
recheck the journal diameter. If the Plastigauge
was wider at one end than the other, the journal
may be tapered (refer to Section 19).
Final connecting rod refitting
19Carefully scrape all traces of the
Plastigauge material off the rod journal and/or
bearing face. Be very careful not to scratchthe bearing, use your fingernail or the edge of
a credit card to remove the Plastigauge.
20Make sure the bearing faces are perfectly
clean, then apply a uniform layer of clean
moly-base grease or engine assembly lube to
both of them. You’ll have to push the piston
higher into the cylinder to expose the face of
the bearing insert in the connecting rod, be
sure to slip the protective hoses over the
connecting rod bolts first.
21At this time, remove the original
connecting rod bolts/nuts and replace them
with new bolts/nuts. They are of a design
which requires they be used only once. The
old ones are OK for Plastigauge checking, but
for final assembly use only new connecting
rod bolts/nuts. Refit the rod cap and tighten
the nuts to the torque listed in this Chapter’s
Specifications. Again, work up to the torque in
three steps.
22Repeat the entire procedure for the
remaining pistons/connecting rod assemblies.
23The important points to remember are:
a) Keep the back sides of the bearing inserts
and the insides of the connecting rods and
caps perfectly clean during assembly..
b) Make sure you have the correct piston/
connecting rod assembly for each
cylinder.
c) The dimple on the piston must face the
front of the engine.
d) Lubricate the cylinder walls with clean oil.
e) Lubricate the bearing faces when refitting
the rod caps after the oil clearance has
been checked.
24After all the piston/connecting rod
assemblies have been properly installed,
rotate the crankshaft a number of times by
hand to check for any obvious binding.
25As a final step, the connecting rod
endplay must be checked. Refer to Section 13
for this procedure.
26Compare the measured endplay to this
Chapter’s Specifications to make sure it’s
correct. If it was correct before dismantling
and the original crankshaft and connecting
rods were reinstalled, it should still be right.
However, if new connecting rods or a new
crankshaft were installed, the endplay may beinadequate. If so, the connecting rods will
have to be removed and taken to an
automotive machine workshop for resizing.
26 Initial start-up
and running-in after overhaul
1
Warning: Have a suitable fire
extinguisher handy when starting
the engine for the first time.
1Once the engine has been installed in the
vehicle, double-check the engine oil and
coolant levels.
2With the spark plugs out of the engine and
the ignition system and fuel pump disabled,
crank the engine until oil pressure registers on
the gauge or the light goes out.
3Refit the spark plugs, hook up the plug
leads and restore the ignition system and fuel
pump functions.
4Start the engine. It may take a few
moments for the fuel system to build up
pressure, but the engine should start without
a great deal of effort.
5After the engine starts, it should be allowed
to warm up to normal operating temperature.
While the engine is warming up, make a
thorough check for fuel, oil and coolant leaks.
6Shut the engine off and recheck the engine
oil and coolant levels.
7Drive the vehicle to an area with no traffic,
accelerate from 30 to 50 mph, then allow the
vehicle to slow to 30 mph with the throttle
closed. Repeat the procedure 10 or 12 times.
This will load the piston rings and cause them
to seat properly against the cylinder walls.
Check again for oil and coolant leaks.
8Drive the vehicle gently for the first
500 miles (no sustained high speeds) and
keep a constant check on the oil level. It is not
unusual for an engine to use oil during the
running-in period.
9At approximately 500 to 600 miles, change
the oil and filter.
10For the next few hundred miles, drive the
vehicle normally. Do not pamper it or abuse it.
11After 2000 miles, change the oil and filter
again and consider the engine run-in.
2B•18 Engine removal and overhaul procedures
25.17 Measure the width of the crushed
Plastigauge to determine the big-end
bearing oil clearance
3261 Jaguar XJ6

3261 Jaguar XJ6
MOT test checksREF•11
MExamine the handbrake mechanism,
checking for frayed or broken cables,
excessive corrosion, or wear or insecurity of
the linkage. Check that the mechanism works
on each relevant wheel, and releases fully,
without binding.
MIt is not possible to test brake efficiency
without special equipment, but a road test can
be carried out later to check that the vehicle
pulls up in a straight line.
Fuel and exhaust systems
MInspect the fuel tank (including the filler
cap), fuel pipes, hoses and unions. All
components must be secure and free from
leaks.
MExamine the exhaust system over its entire
length, checking for any damaged, broken or
missing mountings, security of the retaining
clamps and rust or corrosion.
Wheels and tyres
MExamine the sidewalls and tread area of
each tyre in turn. Check for cuts, tears, lumps,
bulges, separation of the tread, and exposure
of the ply or cord due to wear or damage.
Check that the tyre bead is correctly seated
on the wheel rim, that the valve is sound andproperly seated, and that the wheel is not
distorted or damaged.
MCheck that the tyres are of the correct size
for the vehicle, that they are of the same size
and type on each axle, and that the pressures
are correct.
MCheck the tyre tread depth. The legal
minimum at the time of writing is 1.6 mm over
at least three-quarters of the tread width.
Abnormal tread wear may indicate incorrect
front wheel alignment.
Body corrosion
MCheck the condition of the entire vehicle
structure for signs of corrosion in load-bearing
areas. (These include chassis box sections,
side sills, cross-members, pillars, and all
suspension, steering, braking system and
seat belt mountings and anchorages.) Any
corrosion which has seriously reduced the
thickness of a load-bearing area is likely to
cause the vehicle to fail. In this case
professional repairs are likely to be needed.
MDamage or corrosion which causes sharp
or otherwise dangerous edges to be exposed
will also cause the vehicle to fail.
Petrol models
MHave the engine at normal operating
temperature, and make sure that it is in good
tune (ignition system in good order, air filter
element clean, etc).
MBefore any measurements are carried out,
raise the engine speed to around 2500 rpm,
and hold it at this speed for 20 seconds. Allowthe engine speed to return to idle, and watch
for smoke emissions from the exhaust
tailpipe. If the idle speed is obviously much
too high, or if dense blue or clearly-visible
black smoke comes from the tailpipe for more
than 5 seconds, the vehicle will fail. As a rule
of thumb, blue smoke signifies oil being burnt
(engine wear) while black smoke signifies
unburnt fuel (dirty air cleaner element, or other
carburettor or fuel system fault).
MAn exhaust gas analyser capable of
measuring carbon monoxide (CO) and
hydrocarbons (HC) is now needed. If such an
instrument cannot be hired or borrowed, a
local garage may agree to perform the check
for a small fee.
CO emissions (mixture)
MAt the time of writing, the maximum CO
level at idle is 3.5% for vehicles first used after
August 1986 and 4.5% for older vehicles.
From January 1996 a much tighter limit
(around 0.5%) applies to catalyst-equipped
vehicles first used from August 1992. If the
CO level cannot be reduced far enough to
pass the test (and the fuel and ignition
systems are otherwise in good condition) then
the carburettor is badly worn, or there is some
problem in the fuel injection system or
catalytic converter (as applicable).
HC emissionsMWith the CO emissions within limits, HC
emissions must be no more than 1200 ppm
(parts per million). If the vehicle fails this test
at idle, it can be re-tested at around 2000 rpm;
if the HC level is then 1200 ppm or less, this
counts as a pass.
MExcessive HC emissions can be caused by
oil being burnt, but they are more likely to be
due to unburnt fuel.
Diesel models
MThe only emission test applicable to Diesel
engines is the measuring of exhaust smoke
density. The test involves accelerating the
engine several times to its maximum
unloaded speed.
Note: It is of the utmost importance that the
engine timing belt is in good condition before
the test is carried out.
M
Excessive smoke can be caused by a dirty
air cleaner element. Otherwise, professional
advice may be needed to find the cause.
4Checks carried out on
YOUR VEHICLE’S EXHAUST
EMISSION SYSTEM