1997 FORD RANGER wheel

74
*
[CF20450(R)01/96]
RWARNING
LOCK position does not lock the gearshift on
floor-mounted manual transaxle gearshifts. If the parking
brake is not set and the gearshift is moved out of gear,
your vehicle may move unexpectedly and injure someone.
*
[CF20470(R)05/96]
RWARNING
Do not leave the vehicle unattended with the transfer
case in the N (Neutral) position. Always set the parking
brake fully and turn off the ignition when leaving the
vehicle.
*
[CF20480(R)01/96]
LOCK is the only position that allows you to remove the key.
The LOCK feature helps to protect your vehicle from theft.
*
[CF20482(R)01/96]
If your key is stuck in the LOCK position and will not turn,
move your steering wheel left or right until the key turns freely.
*
[CF20484(R)01/96]
OFF allows you to shut off the engine and all accessories
without locking the steering wheel or the automatic
transmission gearshift lever.
*
[CF20486(R)01/96]
ON allows you to test your vehicle's warning lights (except the
brake system warning light) to make sure they work before you
start the engine. The key returns to the ON position once the
engine is started and remains in this position while the engine
runs.
*
[CF20490(R)01/96]
START cranks the engine. Release the key once the engine starts
so that you do not damage the starter. The key should return to
ON when you release it. The START position also allows you to
test the brake warning light.
File:05uncfr.ex
Update:Thu Mar 20 08:51:14 1997

Controls and Features
79
%*
[CF26200(R)05/96]
Tilt Steering (If equipped)
*
[CF26250(R)02/96]
RWARNING
Never adjust the steering wheel when the vehicle is
moving.
[CF26400(R)01/96]
7-1/2 pica art:0020088-D
Tilt steering wheel lever
[CF26450(R)04/96]
To change the position of the steering wheel, push the release
lever under the steering column away from you. Tip the
steering wheel to the desired position. Pull the lever back into
place to lock the steering wheel.
*
[CF27250(R)01/96]
Be sure the steering wheel locks in a notch. It is not infinitely
adjustable. Do not adjust the steering wheel while the vehicle is
in motion.
%*
[CF27300(R)03/96]
Speed Control (If equipped)
*
[CF27400(R)05/96]
The speed of the vehicle cannot be automatically controlled until
the vehicle speed is at or above 30 mph (48 km/h).
*
[CF27450(R)05/96]
Use of radio transmitting equipment that is not Federal
Communications Commission (FCC) or in Canada the Canadian
Radio and Telecommunications Commission (CRTC) approved
may cause the speed control to malfunction. Therefore, use only
properly installed FCC (CRTC in Canada) approved radio
transmitting equipment in your vehicle.
File:05uncfr.ex
Update:Thu Mar 20 08:51:14 1997

Controls and Features
97
%*
[CF80560(R)05/96]
Replacing lost transmitters
[CF80562(R)01/96]
In the event a transmitter is lost, you should take your vehicle's
transmitters to your dealer to have the remote entry system
deprogrammed for the lost transmitter. This is necessary to
prevent further unauthorized use of the lost transmitter.
*
[CF80564(R)01/96]
You can also purchase additional transmitters (up to 4
transmitters can be used) from your dealer. You will need to
take all your transmitters to the dealer so they can program
them to the remote entry system all at the same time.
%*
[CF80570(R)01/96]
Illuminated Entry System (If equipped)
*
[CF80574(R)01/96]
This system will provide illumination of the vehicle's interior
courtesy lamps when either outside front door handle is pulled
or when the remote entry system is used to unlock the door or
sound the personal alarm. The system will automatically turn
off after approximately 25 seconds or when the ignition is
turned to the RUN or ACC position.
[CF80578(R)04/96]
NOTE: The inside lights will not turn off if you have turned
them on with the dimmer thumbwheel or if any door
is open.
%*
[CF80600(R)01/96]
Battery Saver
[CF80610(R)04/96]
When the ignition is turned off, the vehicle will turn off battery
voltage to all of these lights after 40 minutes: glove box, engine
compartment, overhead console, mirror, courtesy and
interior (including cargo) lamps.
*
[CF80630(R)01/96]
This will prevent draining of the battery if these lights have
been left on inadvertently or if a door is not completely closed.
Battery voltage to these lamps will be restored when the remote
entry transmitter is used, any door is opened, or the ignition
key is turned on again.
File:05uncfr.ex
Update:Thu Mar 20 08:51:14 1997

128
[SS12900(R)01/96]
The driver air bag is in the center of the steering wheel. The
right front passenger seat air bag (if equipped) is in the upper
right hand section of the instrument panel ledge above the
glove compartment.
*
[SS13010(R)05/96]
If a collision occurs, the sensors sense the severity of the impact
and activate the air bags if necessary. The air bag system is
designed to deploy in frontal and front-angled collisions more
severe than hitting a parked vehicle (of similar size and weight)
head-on at about 28 mph (45 km/h). Because the system senses
the crash severity rather than vehicle speed, some frontal
collisions at speeds above 28 mph (45 km/h) will not inflate the
air bag.
*
[SS13020(R)05/96]
When the sensors activate the system, the air bags inflate
rapidly, filling with non-toxic nitrogen gas in a fraction of a
second. Immediately after inflation, the air bags deflate by
releasing the nitrogen gas through vent holes. The whole
process takes place in a matter of seconds.
[SS13025(R)05/96]
RWARNING
Do not place objects or mount equipment on or near the
air bag cover on the steering wheel or in front seat areas
that may come in contact with a deploying air bag.
Failure to follow this instruction may increase the risk of
personal injury in the event of a collision.
*
[SS13030(R)05/96]
RWARNING
Several air bag system components get hot after inflation.
Do not try to touch them after inflation.
File:06unssr.ex
Update:Fri Mar 21 09:43:41 1997

148
%*
[TO06200(R)01/96]
Starting Your Engine
*
[TO06300(R)01/96]
To start your engine:
*
[TO06400(R)01/96]1.
Follow the steps underPreparing to Start Your Vehicleat the
beginning of this section.
*
[TO06425(R)01/96]2.
Turn the ignition key to the ON position.
*
[TO06451(R)01/96]3.
DO NOT depress the accelerator pedal when starting your
engine. DO NOT use the accelerator while the vehicle is
parked.
*
[TO06475(R)01/96]4.
Turn the key to the START position (cranking) until the
engine starts. Allow the key to return to the ON position
after the engine has started.
*
[TO06501(R)01/96]
If you have difficulty in turning the key, rotate the steering
wheel slightly because it may be binding.
%*
[TO06510(R)01/96]
For a cold engine:
*
[TO06515(R)01/96]
n
At temperatures10ÊF (-12ÊC) andbelow:If the engine does
not start infifteen (15) secondson the first try, turn the key
to OFF, wait approximately ten (10) seconds so you do not
flood the engine, then try again.
*
[TO06520(R)01/96]
n
At temperaturesabove10ÊF(-12ÊC):If the engine does not
start infive (5) secondson the first try, turn the key to OFF,
wait approximately ten (10) seconds so you do not flood the
engine, then try again.
%*
[TO06521(R)01/96]
For a warm engine:
*
[TO06522(R)01/96]
n
Do not hold the key in the START position for more than
five (5) secondsat a time. If the engine does not start within
five (5) seconds on the first try, turn the key to the OFF
position. Wait a few seconds after the starter stops, then try
again.
*
[TO06575(R)01/96]
Whenever you start your vehicle, release the key as soon as the
engine starts. Excessive cranking could damage the starter.
File:08untor.ex
Update:Thu Mar 20 08:53:27 1997

170
*
[GF10445(R)05/96]
When to use 1 (Low)
*
[GF10450(R)05/96]
With the gearshift in the 1 (First) position, maximum engine
braking is provided. This position provides 1 (First) gear
operation only with no automatic upshifts. To obtain upshifts,
the gearshift must be moved out of this position. Use the 1
(First) position to drive up steep grades or to provide maximum
engine braking on downgrades.
*
[GF10455(R)05/96]
Forced Downshifts
[GF10460(R)05/96]
To gain acceleration in
j(Overdrive) or Drive (O/D OFF)
when passing another vehicle, push the accelerator to the floor.
The transmission will downshift to the appropriate gear: fourth,
third, second or first gear.
%*
[GF10490(R)05/96]
Traction-Lok Rear Axle (If equipped)
*
[GF10492(R)05/96]
This axle provides added drive away traction on slippery
surfaces, particularly when one or more wheels are on a surface
with poor traction.
*
[GF10494(R)03/96]
Extended use of other than matching size tires on a
Traction-Lok rear axle could result in a permanent reduction in
effectiveness. This loss of effectiveness does not affect normal
driving and should not be noticeable to the driver.
[GF11300(R)01/96]
Manual Transmission Operation
%*
[GF11400(R)01/96]
Using the Clutch
*
[GF11500(R)01/96]
Make sure the gearshift lever is in the N (Neutral) position and
your right foot is holding down the brake pedal. Then press the
clutch pedal to the floor with your left foot. Manual
transmission vehicles have a starter interlock switch. The starter
will not crank until the clutch pedal is fully depressed. Start the
engine and allow it to idle for a few seconds. Move the
gearshift into 1 (First) or R (Reverse).
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997

176
[GF16190(R)05/96]
Four-wheel drive operation (4x4 HIGH or 4x4 LOW) on dry
pavement is not recommended. Operating the vehicle in
four-wheel drive on dry pavement will increase noise, vibration,
tire wear, decrease fuel economy, and make four-wheel drive
disengagement difficult for the transfer case.
[GF16200(R)05/96]
Electric shift system indicator lights
[GF16210(R)05/96]
A 4WD indicator light and a 4WD LOW indicator light are
located in the instrument cluster. If either light flashes, take
your vehicle in for service.
[GF16220(R)05/96]
n
Two-Wheel Drive mode Ð Neither the 4WD nor the 4WD
LOW lights are lit.
[GF16230(R)05/96]
n
4WD High Ð Only the 4WD light is lit.
[GF16240(R)05/96]
n
4WD LOW mode Ð Both the 4WD and 4WD LOW lights
are lit.
[GF16250(R)05/96]
To shift from Two-Wheel Drive to 4WD High:
[GF16260(R)05/96]
To shift into 4WD High rotate the 4WD switch located on the
instrument panel to 4x4 High. This shift can be done at a stop
or at speeds up to 55 miles per hour (88 km/h). When the
vehicle is driven, the automatic locking hubs will engage. If the
vehicle is stopped while in 4WD and the vehicle direction is
reversed from the previous direction, the automatic locking hubs
will momentarily disengage and re-engage. The automatic
locking hubs may click as they automatically engage in the new
direction.
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997

Driving
177
[GF16270(R)05/96]
10-1/2 pica
art:0020628-D
Select drive rotary switch
[GF16280(R)05/96]
At extremely low temperatures, it may be necessary to slow
down or even stop to shift from two wheel drive to 4WD.
[GF16290(R)05/96]
The initial shift from two-wheel drive to 4WD while the vehicle
is moving can cause some momentary clunk and ratcheting
sounds. This is the front drivetrain coming up to speed and the
automatic locking hubs engaging and is not a cause for concern.
[GF16300(R)05/96]
Because of possible damage to powertrain components, never
shift from two-wheel drive to 4WD with the rear wheels
slipping.
[GF16310(R)05/96]
To shift from 4WD High to Two-Wheel Drive:
[GF16320(R)05/96]
Rotate the 4WD switch to 2WD; the 4WD light on the
instrument cluster will go out, indicating the vehicle is in
two-wheel drive. This can be done at any speed. To disengage
the automatic locking hubs, operate the vehicle in two-wheel
drive in the opposite direction for approximately 10 feet (3
meters) in a straight line.
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997