1997 FORD RANGER engine

Instrumentation
23
*
[IS11301(R)01/96]
The pointer moves from the C (cold) mark into the Normal
band as the engine coolant warms up. It is acceptable for the
pointer to fluctuate within the Normal band under normal
driving conditions. Under certain driving conditions, such as
heavy stop and go traffic or driving up hills in hot weather, the
pointer may move to the top of the Normal band.
*
[IS11401(R)04/96]
If, under any circumstances, the pointer moves above the
normal band, the engine is overheating and continued operation
may cause engine damage.
*
[IS11501(R)03/96]
If your engine overheats:
*
[IS11601(R)03/96]1.
Pull off the road as soon as it is safely possible.
*
[IS11701(R)03/96]2.
Turn off the engine. If you do not stop the engine as soon as
safely possible, severe engine damage could result.
*
[IS11801(R)03/96]3.
Let the engine cool.DO NOT REMOVE COOLANT
SYSTEM FILL CAP UNTIL THE ENGINE IS COOL.
*
[IS11901(R)01/96]4.
Check the coolant level following the instructions on
checking and adding coolant to your engine. Refer toEngine
coolantin the Index. If you do not follow these instructions,
you or others could be injured.
*
[IS12240(R)01/96]
If the coolant continues to overheat, have the coolant system
serviced as soon as possible.
[IS12300(R)01/96]
7-1/2 pica art:0020067-F
Engine coolant temperature gauge Ð mechanical cluster
File:03unisr.ex
Update:Thu Mar 20 09:21:14 1997

24
[IS12325(R)01/96]
7-1/2 pica art:0021154-C
Engine coolant temperature gauge Ð mechanical cluster with tachometer
%*
[IS12601(R)03/96]
Speedometer
*
[IS12700(R)03/96]
The speedometer tells you how many miles (kilometers) per
hour your vehicle is moving.
*
[IS12753(R)03/96]
Some vehicles are equipped with a vehicle speed (mph/km/h)
limiting device that is contained within the Powertrain Control
Module (PCM). The purpose of this device is to maintain peak
vehicle speed below a specified limit. (Vehicle speed limits may
vary based on engine displacement.)
*
[IS12756(R)03/96]
If you are experiencing an ªengine cut-outº condition at high
speeds, it may be the result of this limiting device. It is a
normal condition and can be avoided by reducing
vehicle/engine speed.
[IS12790(R)01/96]
10-1/2 pica
art:0020873-G
Speedometer
File:03unisr.ex
Update:Thu Mar 20 09:21:14 1997

Instrumentation
25
%*
[IS12801(R)03/96]
Odometer
*
[IS12900(R)01/96]
The odometer tells you the total number of miles (kilometers)
your vehicle has been driven.
%*
[IS13000(R)01/96]
Trip Odometer
*
[IS13100(R)04/96]
If you want to track your mileage up to 999.9 miles
(kilometers), use the trip odometer. Simply set the trip odometer
to zero by pressing the reset control firmly when beginning the
distance you wish to measure.
% [IS13200(R)04/96]
Tachometer (If equipped)
*
[IS13300(R)03/96]
The tachometer will show you the engine's speed measured in
revolutions per minute (RPM).
*
[IS13400(R)03/96]
The tachometer may move slightly when the key is placed in
the ACC or ON position, with the engine off. This is normal
and does not affect the performance of the tachometer when the
engine is running.
*
[IS13525(R)03/96]
Some vehicles are equipped with an engine speed (RPM)
limiting device contained within the powertrain control module
(PCM). The purpose of this device is to maintain peak engine
speed (RPM) below a specified limit. This feature is only
evident on automatic transmission vehicles when shifting
manually (1, 2, D) and on all manual transmission units. (Engine
speed limits may vary based on engine displacement.)
*
[IS13550(R)03/96]
If you are experiencing an ªengine cut-outº condition at high
speeds, it may be the result of this limiting device. It is a
normal condition and can be avoided by reducing
vehicle/engine speed.
File:03unisr.ex
Update:Thu Mar 20 09:21:14 1997

26
[IS13650(R)05/96]
10-1/2 pica
art:0020258-G
Tachometer
[IS13675(R)01/96]
NOTE: If the 4.0L engine exceeds 5200 RPM, the PCM will
restrict fuel flow to maintain engine speed at or below
5200 RPM. This function is designed to protect the
engine and should be considered normal operation.
File:03unisr.ex
Update:Thu Mar 20 09:21:14 1997

68
*
[CF02550(R)01/96]
Operating tips
*
[CF02600(R)03/96]
The following tips will help you to get the most satisfaction
from your air conditioning (if equipped) and heater system.
[CF02650(R)01/96]
n
In humid weather, selectVbefore starting your engine.
This will help to prevent windshield fogging. After a few
minutes of operation, you may select another function.
[CF02700(R)01/96]
n
To prevent humidity buildup inside your vehicle, always
drive with the air conditioner or heater system turned on.
*
[CF02750(R)01/96]
n
Do not put objects under the front seats that interfere with
the flow of air to the back seat area.
[CF02800(R)01/96]
n
Remove any snow, ice, or leaves from the air intake area of
your air conditioner and heater system that could block the
air intake. The intake area is located at the bottom of the
windshield.
*
[CF02900(R)01/96]
Heater Controls (Heater-Only Vehicles)
[CF02950(R)01/96]
The control for your heater system is located at the center of the
instrument panel below the radio. The heater will operate only
when the ignition key is turned to the ON position. Your heater
will heat and/or ventilate your vehicle interior depending on
the function position and temperature you select. The function
selector control knob allows you to select heating or ventilation
and determine where the air will be directed. The temperature
control knob setting determines the temperature of the air that
flows into the vehicle.
File:05uncfr.ex
Update:Thu Mar 20 08:51:14 1997

Controls and Features
73
*
[CF20300(R)01/96]
Clock Controls on Electronic Radios
[CF20400(R)02/96]
The electronic radios have a built-in clock. For complete
operating instructions, refer to theAudio Sectionin this Owner
Guide.
*
[CF20405(R)05/96]
The controls on the steering column and wheel are designed to
give you easy access to the controls while you are driving.
*
[CF20410(R)01/96]
Ignition
%*
[CF20420(R)01/96]
Understanding the Positions of the Ignition
[CF20430(R)01/96]
7-1/2 pica art:0021143-A
The positions of the key in the ignition lock cylinder.
%*
[CF20440(R)04/96]
ACCESSORY allows some of your vehicle's electrical accessories
such as the radio and the windshield wipers to operate while
the engine is not running.
*
[CF20442(R)03/96]
In order to turn the key from the ON or OFF position to the
ACCESSORY position, you must push the key release button if
your vehicle's manual transmission gearshift is mounted on the
floor.
*
[CF20444(R)01/96]
LOCK locks the steering wheel and gearshift lever.
File:05uncfr.ex
Update:Thu Mar 20 08:51:14 1997

74
*
[CF20450(R)01/96]
RWARNING
LOCK position does not lock the gearshift on
floor-mounted manual transaxle gearshifts. If the parking
brake is not set and the gearshift is moved out of gear,
your vehicle may move unexpectedly and injure someone.
*
[CF20470(R)05/96]
RWARNING
Do not leave the vehicle unattended with the transfer
case in the N (Neutral) position. Always set the parking
brake fully and turn off the ignition when leaving the
vehicle.
*
[CF20480(R)01/96]
LOCK is the only position that allows you to remove the key.
The LOCK feature helps to protect your vehicle from theft.
*
[CF20482(R)01/96]
If your key is stuck in the LOCK position and will not turn,
move your steering wheel left or right until the key turns freely.
*
[CF20484(R)01/96]
OFF allows you to shut off the engine and all accessories
without locking the steering wheel or the automatic
transmission gearshift lever.
*
[CF20486(R)01/96]
ON allows you to test your vehicle's warning lights (except the
brake system warning light) to make sure they work before you
start the engine. The key returns to the ON position once the
engine is started and remains in this position while the engine
runs.
*
[CF20490(R)01/96]
START cranks the engine. Release the key once the engine starts
so that you do not damage the starter. The key should return to
ON when you release it. The START position also allows you to
test the brake warning light.
File:05uncfr.ex
Update:Thu Mar 20 08:51:14 1997

Controls and Features
97
%*
[CF80560(R)05/96]
Replacing lost transmitters
[CF80562(R)01/96]
In the event a transmitter is lost, you should take your vehicle's
transmitters to your dealer to have the remote entry system
deprogrammed for the lost transmitter. This is necessary to
prevent further unauthorized use of the lost transmitter.
*
[CF80564(R)01/96]
You can also purchase additional transmitters (up to 4
transmitters can be used) from your dealer. You will need to
take all your transmitters to the dealer so they can program
them to the remote entry system all at the same time.
%*
[CF80570(R)01/96]
Illuminated Entry System (If equipped)
*
[CF80574(R)01/96]
This system will provide illumination of the vehicle's interior
courtesy lamps when either outside front door handle is pulled
or when the remote entry system is used to unlock the door or
sound the personal alarm. The system will automatically turn
off after approximately 25 seconds or when the ignition is
turned to the RUN or ACC position.
[CF80578(R)04/96]
NOTE: The inside lights will not turn off if you have turned
them on with the dimmer thumbwheel or if any door
is open.
%*
[CF80600(R)01/96]
Battery Saver
[CF80610(R)04/96]
When the ignition is turned off, the vehicle will turn off battery
voltage to all of these lights after 40 minutes: glove box, engine
compartment, overhead console, mirror, courtesy and
interior (including cargo) lamps.
*
[CF80630(R)01/96]
This will prevent draining of the battery if these lights have
been left on inadvertently or if a door is not completely closed.
Battery voltage to these lamps will be restored when the remote
entry transmitter is used, any door is opened, or the ignition
key is turned on again.
File:05uncfr.ex
Update:Thu Mar 20 08:51:14 1997