1997 FORD PROBE ignition

11
%*
[IS01600(ALL)04/96]
Indicator Lights and Chimes
%*
[IS01700(ALL)03/96]
Safety Belt Warning Light and Chime
[IS01800(ALL)01/96]
This warning light and chime remind you to
fasten your safety belt. If you do not fasten your
safety belt before the ignition is turned to ON,
the chime will sound for 4 to 8 seconds and the
warning light will illuminate for 1 to 2 minutes,
or until the safety belt is fastened. If you fasten
the safety belt before the ignition is turned to
ON, neither the light nor chime will activate.
[IS01900(ALL)01/96]
one inch art:0032097-A
Safety belt light
%*
[IS02000(ALL)05/96]
Air Bag Readiness Light
*
[IS02050(ALL)05/96]
This light illuminates for six seconds when the
ignition is turned to the ON position. If the light
fails to illuminate, continues to flash, remains on,
or if a series of five beeps is heard, have the
system serviced as soon as possible.
[IS02100(ALL)01/96]
one inch art:0032051-A
Air bag readiness light
File:03prisp.ex
Update:Thu May 16 09:43:45 1996

12
*
[IS02120(ALL)05/96]
RWARNING
If any of these things happen, even
intermittently, have the air bag system
serviced at your Ford or Lincoln-Mercury
dealer immediately.
%*
[IS02200(ALL)01/96]
Brake System Warning Light
[IS02300(ALL)03/96]
Your vehicle has a divided brake system. If one
part isn't working, the other part can still work
and stop you. For good braking, though, you
need both systems working well. If the warning
light illuminates, there could be a problem. Have
your brake system inspected right away.
[IS02400(ALL)03/96]
This light should illuminate as you start the
vehicle. If it doesn't illuminate then, have it
fixed so it will be ready to warn you if there's a
problem.
[IS02500(ALL)01/96]
one inch art:0030319-E
Brake system and parking brake light
[IS02600(ALL)03/96]
This light illuminates briefly when you turn the
ignition key to START. It normally goes off
shortly after the engine starts and you release
the parking brake, but it may stay on for up to
60 seconds. If the light stays on for longer than
60 seconds or comes on after you have fully
released the parking brake, have the hydraulic
brake system serviced.
File:03prisp.ex
Update:Thu May 16 09:43:45 1996

13
*
[IS02700(ALL)03/96]
This light will also illuminate if the parking
brake does not release fully. If it does stay on
afterthe parking brake is fully released, it
means there may be a brake problem. Pull off
the road and stop carefully. You may notice that
the pedal is harder to push, the pedal may go
closer to the floor, or it may take longer to stop
the vehicle. Try the brakes again after you have
stopped.
*
[IS02800(ALL)03/96]
RWARNING
The BRAKE light indicates that the brakes
may not be working properly. Have the
brakes checked immediately.
%*
[IS02900(ALL)03/96]
Anti-Lock Brake System Warning Light
[IS03000(ALL)03/96]
When the ignition switch is turned to the ON
position, the anti-lock brake system warning
light will illuminate. When the engine is started,
the anti-lock brake system control unit will
determine if all components of the system are
operating correctly. The warning light could
remain on for two to four seconds.
[IS03100(ALL)01/96]
one inch art:0032359-C
The anti-lock brake system warning light
*
[IS03200(ALL)03/96]
RWARNING
If the anti-lock brake system warning
light remains on or comes on while
driving, have the braking system checked
by a qualified service technician as soon
as possible.
File:03prisp.ex
Update:Thu May 16 09:43:45 1996

15 %
*
[IS03800(ALL)05/96]
High Beam Light
*
[IS03900(ALL)03/96]
This light illuminates when the headlamps are
turned to high beam or when you flash the
lights.
*
[IS04000(ALL)01/96]
one inch art:0030174-A
High beam light
%*
[IS04100(ALL)03/96]
Check Engine Warning Light
*
[IS04200(ALL)03/96]
This light illuminates when the electronic engine
control system is not working properly. This is
the computer that controls the operating
conditions of the engine.
*
[IS04300(ALL)01/96]
one inch art:0030175-B
Check engine warning light
[IS04400(ALL)03/96]
This light illuminates briefly when you turn the
ignition to the ON position, but should turn off
when the engine starts. If the light does not
come on when you turn the ignition to the ON
position or if it comes on and stays on when
you are driving, have your vehicle serviced as
soon as possible. This indicates a possible
problem with one of the engine's emission
control systems.You do not need to have your
vehicle towed in.
File:03prisp.ex
Update:Thu May 16 09:43:45 1996

16
*
[IS04500(ALL)04/96]
If the light flashes briefly while you are driving,
it means that the condition is no longer present.
[IS04600(ALL)01/96]
O/D OFF Light (If equipped)
[IS04700(ALL)05/96]
This light tells you that the overdrive off (O/D
OFF) button on the shift selector has been
pushed. When the light is on, the transaxle will
not shift into overdrive. Depressing the button
on the shift selector again will return the vehicle
to ªoverdrive onº mode. The transaxle will be in
the ªoverdrive onº mode when the vehicle is
started even if the O/D OFF mode was selected
when the vehicle was last shut off. Refer to the
Drivingchapter for more information.
[IS04800(ALL)03/96]
If the light does not illuminate when the O/D
OFF button is pressed, or if the light flashes
when you are driving, have your vehicle
serviced at the first opportunity. If this condition
persists, damage could occur to the transaxle.
[IS04900(ALL)01/96]
one inch art:0032053-A
Overdrive OFF light
*
[IS05000(ALL)04/96]
Gauges
%*
[IS05100(ALL)05/96]
Fuel Gauge
*
[IS05200(ALL)01/96]
The fuel gauge displays approximately how
much fuel you have in the fuel tank.
*
[IS05300(ALL)01/96]
The ignition must be turned off while putting
fuel in the tank in order to get a correct fuel
gauge reading after the ignition is turned on.
File:03prisp.ex
Update:Thu May 16 09:43:45 1996

17
*
[IS05400(ALL)01/96]
The fuel gauge indicator may vary slightly while
the vehicle is in motion. This is the result of fuel
movement within the tank. You can get a more
accurate reading with the vehicle on smooth,
level ground.
[IS05500(ALL)01/96]
Charging System Gauge
[IS05600(ALL)01/96]
This gauge tells you your battery's voltage when
you turn your ignition key to ON. When you
start your engine, the pointer should move to
the NORMAL range if you are not operating
any electrical accessories. (If electrical accessories
are operating and the engine is not running, the
pointer may move into the red area).
[IS05700(ALL)01/96]
If the pointer moves into the red area when no
electrical accessories are operating, have the
vehicle's electrical system checked.
%*
[IS05800(ALL)04/96]
Engine Oil Pressure Gauge
[IS05900(ALL)01/96]
The gauge needle should stay in the NORMAL
range (indicating normal engine oil pressure). If
the needle drops below the NORMAL range into
the low range, there is a loss of oil pressure.
[IS06000(ALL)01/96]
If this happens:
*
[IS06100(ALL)04/96]
1. Pull off the road as soon as safely possible.
*
[IS06200(ALL)04/96]
2. Shut off the engine immediately or severe
engine damage could result.
[IS06300(ALL)01/96]
3. Check the oil level when the vehicle is on
level ground.
[IS06400(ALL)01/96]
4. Add only as much oil as the engine needs
before you drive the vehicle again. Do not
overfill the oil reservoir. For more
information, seeAdding engine oilin the
Index.
File:03prisp.ex
Update:Thu May 16 09:43:45 1996

22
%*
[AS00975(ALL)10/95]
Compact Disc Radio
*
[AS01000(ALL)10/95]
The Compact Disc Radio combines the Electronic
Stereo Radio with the Ford Compact Disc Player.
*
[AS01300(ALL)08/95]
Using the Controls on Your New Radio/CD
Player
*
[AS01400(ALL)04/92]
Most of the features of this unit work for both
radio and CD operation, depending on which
mode the unit is in. Also, some of the buttons
control several different functions, so be sure to
read all of the operating instructions carefully.
*
[AS01500(ALL)03/96]
How to turn the radio on and off
*
[AS01600(ALL)10/95]
Press the ªPOWERº button to turn the radio on.
Press it again to turn it off.
*
[AS01625(ALL)03/96]
How to adjust the volume
*
[AS01650(ALL)03/96]
Press the (R/S) side of the ªVOLº button to
increase/decrease the volume. Bars illuminate in
the display to show the relative volume level.
*
[AS01675(ALL)02/96]
NOTE: If the volume level is set above a
certain listening level when the
ignition switch is turned off, when the
ignition switch is turned back on, the
volume will come back to a ªnominalº
listening level. However, if the radio
power is turned off, the volume will
remain in the position it was set at
when radio power was switched off.
*
[AS01700(ALL)03/96]
Selecting the AM or FM frequency band
*
[AS01800(ALL)10/95]
Push the ªAM/FMº button to select the desired
frequency band. When in the radio mode,
pushing the button more than once will alternate
between AM, FM1 and FM2. These functions are
used with the station memory buttons described
underHow to tune radio stations.
File:04prasp.ex
Update:Mon Jun 3 10:03:33 1996

29
*
[AS07600(ALL)04/96]
How to insert a disc and begin play
*
[AS07700(ALL)10/95]
Insert one disc,label side upinto the disc
opening. When inserted, the disc automatically
loads into the unit and play starts at the
beginning of the first track (selection).
*
[AS07800(ALL)04/96]
When the disc reaches the end, the disc player
automatically returns to the beginning of the
disc and resumes playing.
[AS07900(ALL)04/96]
NOTE: Once a disc is inserted, the disc
opening is secured to prevent the
accidental insertion of a second disc.
*
[AS08000(ALL)10/95]
NOTE: The CD player has heat protection
circuitry to protect the laser diode. If
the temperature of the player reaches
167ÊF (75ÊC), theheat detection circuit
will shut off the player and ªTOO
HOTº will scroll in the display for
approximately five seconds (radio will
resume playing). When the temperature
returns to normal operating range, the
CD player will again be operational.
*
[AS08100(ALL)10/95]
How to stop and restart the CD player
*
[AS08200(ALL)04/96]
When a disc is loaded, the unit automatically
enters the play mode and the play indicator (
a)
illuminates. To stop temporarily, press the
ªPLAY/STOPº button or the ªAM/FMº button.
The stop indicator (
X) in the display illuminates
and operation returns to the radio mode. To
resume CD play, press the ªPLAY/STOPº
button once again.
*
[AS08300(ALL)10/95]
NOTE: If the ignition key is turned OFF
during play and then is set to the ON
or ACCESSORY position, the CD
player will resume playing in the mode
it was in when ignition was turned off.
File:04prasp.ex
Update:Mon Jun 3 10:03:33 1996