1997 FORD F150 belt

Brake system warning
Extinguishes when the parking
brake is released. Illumination after
releasing the parking brake
indicates low brake fluid level.
Safety belt
Illuminates when the ignition is
switched on to remind you to
fasten your safety belts. For more
information, refer toUsing the
safety restraints properlyin the
Seating and safety restraints
chapter.
Air bag readiness
Briefly illuminates when the
ignition is turned to On. If the light
fails to illuminate, continues to
flash or remains on, have the
system serviced. For more
information, refer to
Supplemental restraints system
(SRS)in theSeating and safety
restraintschapter.
Check engine warning light
This light illuminates when the
engine's Emission Control System
requires service. It will also
illuminate when the ignition key is
in the On position and the engine
is off. Refer toWhat you should
know about the on-board
diagnostic (OBD II) systemin the
Maintenance and carechapter.
!
BRAKE
CHECK
ENGINE
com_safety_belt.01
f12_air_bag_readiness
f12_check_engine
f12_tcil_light
Instrumentation
10

warning and indicator lights shown
above will illiminate for a brief
time. If any of these lights do not
illuminate, contact your dealer for
service.
Headlamps on warning chime
Sounds when the headlamps are
on, the key is out of the ignition
and any door is opened.
Key-in-ignition warning chime
Sounds when the key is left in the
ignition and any door is opened.
The chime is not active when the
ignition key is in the On position.
Safety belt warning chime
For information on the safety belt
warning chime, refer to the
Seating and safety restraints
chapter.
Supplemental restraint system
(SRS) warning chime
For information on the SRS
warning chime, refer to the
Seating and safety restraints
chapter.
f12_headlamps_on
f12_key_in_ignition
com_safety_chime.01
com_srs_chime.01
f12_gauges
Instrumentation
13

60/40 split rear seat (if
equipped)
When folded down, the rear seats
provide a ªload floorº of additional
storage space. To fold down the
rear seats:
1. Pull the straps to lower the seat
cushions.
2. Store the center safety belt in
the opening on the seat back.
When returning the seats to their
normal position:
1. Clear the load floor before
folding seat up.
2. Ensure the seat cushion is
latched into place.
3. Remove center safety belt from
its stowed position.
Check to assure that 60/40
Split rear seat cushion is
latched by pulling up and
forward on lap belt buckles.
SAFETY RESTRAINTS
Safety restraints precautions
The use of safety belts helps to
restrain you and your passengers
in case of a collision. In most
states and Canada, the law
requires the use of safety belts.
Always drive and ride with
your seatback upright and
the lap belt snug and low across
the hips.
f12_seat_belts
f12_safety_res_prec
Seating and safety restraints
58

All occupants of the
vehicle, including the
driver, should always wear their
safety belts.
To prevent the risk of
injury, make sure children
sit where they can be properly
restrained.
It is extremely dangerous
to ride in a cargo area,
inside or outside of a vehicle. In
a collision, people riding in these
areas are more likely to be
seriously injured or killed. Do not
allow people to ride in any area
of your vehicle that is not
equipped with seats and safety
belts. Be sure everyone in your
vehicle is in a seat and using a
safety belt properly.
f12_using_sr_properly
Seating and safety restraints
59

Using safety restraints properly
Combination lap and shoulder
belts
1. To connect the safety belt,
insert the tongue into the buckle.
2. To disconnect the safety belt,
push the red release button and
remove the tongue from the
buckle.
The front and rear (if equipped)
outboard safety restraints in your
vehicle are combination lap and
shoulder safety belts. The outboard
passenger safety belts have the
two types of locking modes
described below:
Vehicle sensitive (emergency)
locking mode
The vehicle sensitive mode is the
normal retractor mode, allowing
free shoulder belt length
adjustment to your movements and
locking in response to vehicle
movement. For example, if the
driver brakes suddenly or turns a
corner sharply, or the vehicle
receives an impact of
approximately 8 km/h (5 mph) or
more the combination safety belts
will lock to help reduce forward
PRESS
f12_comb_lap_sh_belts
Seating and safety restraints
60

movement of the driver and
passengers.
The front seat belt system can also
be made to lock manually by
quickly pulling on the shoulder
belt. Rear seat belts (if equipped)
cannot be made to lock up by
pulling quickly on the belt.
Automatic locking mode
In this mode, the shoulder belt is
automatically pre-locked. The belt
will still retract to remove any
slack in the shoulder belt.
The automatic locking mode is not
available on the driver safety belt.
When to use the automatic
locking mode
²When a tight lap/shoulder belt
fit is desired.
²Any time a child safety seat is
installed in the vehicle. Refer to
Children and infant or child
safety seatslater in this chapter.
f12_auto_lock_mode
f12_when_to_use_alr
f12_how_use_alrSeating and safety restraints
61

Using the automatic locking
mode
The automatic locking mode must
be used when installing a child
safety seat in any outboard
passenger seat.
1. Buckle the combination lap and
shoulder belt.
2. Grasp the shoulder belt portion
and pull downward until the entire
belt is extracted.
3. Allow the belt to retract. As the
belt retracts, you will hear a
clicking sound. This indicates that
the safety belt is now in the
automatic locking mode.
Cancelling the automatic
locking mode
Disconnect the combination
lap/shoulder belt and allow it to
completely retract to cancel the
automatic locking mode and
activate the vehicle sensitive
(emergency) locking mode.
f12_cancel_alr
f12_front_sbelt_height_adjust
Seating and safety restraints
62

Front seat safety belt height
adjustment
Your vehicle has safety belt height
adjustments for the driver and
passenger seating positions.
Adjust the height of the shoulder
belt so the belt rests across the
middle of your shoulder.
1. Push the button and slide down
to lower the shoulder belt height.
2. Push the button and slide up to
raise the shoulder belt height.
3. Pull down on the height
adjustment assembly to make sure
it is locked in place.
If you have a SuperCab vehicle,
the front passenger seat
combination lap and shoulder belt
height cannot be adjusted.
Lap belts
Lap belts are located in the center
of the front bench or split bench
seat (if equipped) and rear bench
seat (SuperCab only).
Adjusting lap belts
The lap belt does not have a
retractor to automatically adjust
itself during vehicle movement.
f12_lap_belts
f12_adjusting_lap_belts
Seating and safety restraints
63