1997 FORD F SERIES MOTORHOME AND COMMERCIAL CHASSIS tow

13
*
[IS05000( ALL)01/96]
Modification or additions to the vehicle may
cause incorrect operation of the OBD II system.
Additions such as burglar alarms, cellular
phones, and CB radios must be carefully
installed. Do not install these devices by tapping
into or running wires close to powertrain control
system wires or components.
*
[IS05100( ALL)01/96]
The light comes on briefly when you turn the
ignition key toON, but it should turn off when
the engine starts. If the light does not come on
when you turn the ignition toONor if it comes
on and stays on when you are driving, have
your vehicle serviced as soon as possible. This
indicates a possible problem with one of the
vehicle's emission control systems. You do not
need to have your vehicle towed in.
*
[IS05200( ALL)01/96]
If the light turns on and off at one (1) second
intervals while you are driving the vehicle, it
means that the engine is misfiring. If this
condition persists, damage could occur to the
engine or catalytic convertor. Have your vehicle
serviced at the first opportunity. You do not
need to have your vehicle towed in.
*
[IS05300( ALL)01/96]
If the light turns on and off on rare occasions
while you are driving, it means that a
malfunction occurred and the condition corrected
itself.
*
[IS05500( ALL)01/96]
An example of a condition which corrects itself
occurs when an engine running out of fuel
begins to misfire. In this case, the Check Engine
Warning Light may turn on and will then set a
Diagnostic Trouble Code indicating that the
engine was misfiring while the last of the fuel
was being consumed. After refueling, the Check
Engine Warning Light will turn off after the
vehicle has completed three consecutive warm
File:03ltism.ex
Update:Fri Dec 13 11:17:22 1996

15
*
[IS06200( ALL)01/96]
This light comes on every time you turn the
ignition to the ON or START position (engine
off). The light should go off when the engine
starts and the alternator begins to charge.
*
[IS06300(B FM)01/96]
If the light stays on or comes on when the
engine is running, have the electrical system
checked as soon as possible.
%*
[IS07100( ALL)01/96]
Battery Voltage Gauge (Voltmeter)
*
[IS07200( ALL)01/96]
This gauge shows you the battery voltage when
the ignition key is in the ON position.
*
[IS07300( ALL)01/96]
If you are running electrical accessories (when
the engine is off, or idling at a low speed), the
pointer may move toward the lower end of the
normal band. If it stays outside the normal band
area, have your vehicle's electrical system
checked as soon as it is safely possible.
*
[IS07400( ALL)01/96]
If the battery is operating under cold weather
conditions, the pointer may indicate in the upper
range of the NORMAL band while the battery is
charging. If you are running electrical accessories
with the engine off or idling at a low speed, or
the battery is not fully charged, the pointer may
move toward the lower end of the NORMAL
band.
*
[IS07500( ALL)01/96]
If it stays outside the NORMAL band, have your
vehicle's electrical system checked as soon as it
is safely possible.
[IS07700( E M)01/96]
quarter page art:0020863-B
Battery voltage gauge
File:03ltism.ex
Update:Fri Dec 13 11:17:22 1996

21
Controls and Features
[CF00300( M)01/96]
NOTE: The following section does not apply
to Stripped Chassis vehicles. See your
Body Builder's instructions for location
and operation of controls for climate
control systems, lamps and radio.
%*
[CF14100( ALL)01/96]
Turning On the Exterior Lights
*
[CF14200( ALL)01/96]
To turn on your headlamps, parking lamps,
marker lamps, license plate lamps and tail
lamps, use the headlamp switch to the left of the
steering column.
*
[CF14300( ALL)01/96]
1. Pull the headlamp control knob toward you
to the first position. Parking lamps, tail
lamps and marker lamps are now on.
*
[CF14400( ALL)01/96]
2. Pull the headlamp control knob toward you
to the outer position. Headlamps are now on
in addition to the above.
File:05ltcfm.ex
Update:Thu Dec 12 13:31:05 1996

26 %
*
[CF28000( ALL)01/96]
High Beams
*
[CF28100( ALL)01/96]
To turn on the high beams, turn the headlamp
control knob to the headlamp ON position and
push the turn signal lever away from you until
it latches. When the high beams are ON, the
high beam indicator light on the instrument
panel comes on.
*
[CF28200( ALL)01/96]
To turn off the high beams, pull the lever
toward you until it latches. The high beam
indicator light turns off.
*
[CF28300( ALL)01/96]
one third page art:0020074-B
Headlamp high beam switch and turn signal lever
%*
[CF28400( ALL)01/96]
Flashing the Lights
*
[CF28500( ALL)01/96]
To flash the headlamps, pull the lever toward
you for a moment and then release it. The
headlamps will flash whether the headlamp
knob is in the on or off position.
File:05ltcfm.ex
Update:Thu Dec 12 13:31:05 1996

27
%*
[CF28600( ALL)01/96]
Windshield Wipers and Washer
*
[CF28700( ALL)01/96]
To turn on the windshield wipers, the ignition
key must be turned to the ON or ACC position.
*
[CF28800( ALL)01/96]
Turn the knob on the end of the turn signal
lever toward the front of the vehicle. You can
turn it to either the LO or HI speed position.
%*
[CF28900( ALL)01/96]
Variable Interval Wipers
*
[CF29000( ALL)01/96]
In addition to two speed wipers, your vehicle is
equipped with wipers that you can set to
operate at varying intervals. For example, you
can set the interval so they wipe less often when
it drizzles or more often in heavier rain.
*
[CF29100( ALL)01/96]
one third page art:0020831-A
Interval wiper on turn signal lever
*
[CF29200( ALL)01/96]
To set the interval wipers, rotate the knob at the
end of the turn signal lever toward or away
from the instrument panel to the interval
operation you desire.
*
[CF29300( ALL)01/96]
Windshield Washer
*
[CF29400( ALL)01/96]
To clean the windshield, push in the end of the
wiper knob. For a constant spray, keep the knob
pushed in. After you release the knob, the
wipers operate for two to three cycles before
turning off (if wipers were off) or returning to
the selected setting.
File:05ltcfm.ex
Update:Thu Dec 12 13:31:05 1996

30
%*
[CF31500( M)01/96]
Tilt Steering
*
[CF31600( ALL)01/96]
RWARNING
Never adjust the steering wheel when the
vehicle is moving.
[CF31800( M)01/96]
one third page art:0020090-D
Turn signal and tilt release wheel lever
*
[CF31900( ALL)01/96]
To change the position of the steering
column/wheel, pull the release lever on the
column toward you. Tip the steering wheel to
the desired position. Release the lever to lock the
steering wheel in place.
*
[CF32000( ALL)01/96]
Be sure the steering wheel locks in a notch. It is
not infinitely adjustable. Do not adjust the
steering wheel while the vehicle is in motion.
%
*
[CF32200( M)01/96]
Speed Control
*
[CF32300( ALL)01/96]
Your vehicle has speed control, so you can
automatically maintain a constant speed above
30 mph (50 km/h). The switches to operate the
speed control are on the steering wheel.
*
[CF32400( ALL)01/96]
Use of radio transmitting equipment that is not
Federal Communications Commission (FCC) or
in Canada the Canadian Radio and
Telecommunications Commission (CRTC)
approved may cause the speed control to
File:05ltcfm.ex
Update:Thu Dec 12 13:31:05 1996

53
*
[GF07975( ALL)01/96]
RWARNING
DO NOT DRIVE YOUR VEHICLE UNTIL
YOU VERIFY THAT THE BRAKELAMPS
ARE WORKING.
%*
[GF08000( ALL)01/96]
R (Reverse)
*
[GF08025( ALL)01/96]
With the gearshift in the R (Reverse) position,
the vehicle will move backward. You should
always come to a complete stop before shifting
into or out of R (Reverse).
%*
[GF08050( ALL)01/96]
Driving
%*
[GF08075( ALL)01/96]
When to usej(Overdrive)
*
[GF08100( ALL)01/96]
This is the normal driving position. As the
vehicle picks up speed, automatic upshifts to
second, third and fourth gears will occur when
jOverdrive is chosen on the selector and the
transmission control switch has not been
pressed. The transmission will shift into the
correct gear when the right speed is achieved,
for the accelerator pedal position you have
chosen.
*
[GF08125( ALL)01/96]
When to use Drive
*
[GF08150( ALL)01/96]
You will note that there isn't a drive position on
your gearshift indicator. However, you will find
a Transmission Control Switch and an indicator
light labeled ªOverdriveº located on the end of
the gearshift lever. Press this switch and the
word ªOFFº will illuminate on the shift lever
knob. With the word ªOFFº illuminated, the
transmission will operate in gears one through
three. Operating in the Overdrive ªOFFº mode
gives more engine braking than Overdrive and
is useful for descending hills or when towing.
File:09ltgfm.ex
Update:Fri Dec 13 11:22:54 1996

55
*
[GF08325( ALL)01/96]
When to use 1 (Low)
*
[GF08350( ALL)01/96]
Use 1 (Low) to provide maximum engine
braking on steep downgrades. Upshifts from 1
(Low) can be made by manually shifting to 2
(Second) orj(Overdrive). Selection of 1 (Low)
gear provides only low gear operation from
start-up. Selection of 1 (Low) while at higher
speeds provides a shift to second gear, and a
shift to first gear will occur after the vehicle
decelerates to the proper speed.
*
[GF08375( ALL)01/96]
P (Park)
*
[GF08400( ALL)01/96]
Always come to a complete stop before you shift
into P (Park). This position locks the
transmission and prevents the rear wheels from
turning. To securely latch the gearshift in the P
(Park) position, pull it toward you, push it
completely counterclockwise against the stop,
and then push it toward the instrument panel.
*
[GF08425( ALL)01/96]
The gearshift is securely latched in P (Park) if
you cannot rotate it in a clockwise direction
without lifting it toward you.
*
[GF08450( ALL)01/96]
RWARNING
Always set the parking brake fully and
make sure the gearshift is latched in P
(Park). Turn off the ignition whenever you
leave your vehicle.
*
[GF08525( ALL)01/96]
RWARNING
Never leave your vehicle unattended
while it is running.
File:09ltgfm.ex
Update:Fri Dec 13 11:22:54 1996