1997 DODGE NEON lock

[x] Cancel search: lock

key fuse diagram dead battery open trunk airbag disable relay clutch

Load previous 8 pages

Page 109 of 256

DODGE NEON 1997 1.G Wiring Diagrams Workshop Manual Downloaded from www.Manualslib.com manuals search engine 1
5432
11 A/C ON
67
89
0098 7
6
A/C
SWITCH
ILLUM. BLOWER
SWITCH
ILLUM.
MODE
SWITCH
ILLUM. A/C
HEATER
CONTROL
ILLUM.
BLOWER SWITCHA/C
SWITCH
10

Page 110 of 256

DODGE NEON 1997 1.G Wiring Diagrams Workshop Manual Downloaded from www.Manualslib.com manuals search engine RUN A22
5
25
10A
FUSE
5
FUSED
IGN.
(RUN)
SWITCH CYCLING
A/C
C2
22
DB/YL
C2
22
DB/YL
F20
20
WT
F20
22
WT
2C206
2
MODE
SWITCH
OUTPUTA/C
CYCLING
S

Page 112 of 256

DODGE NEON 1997 1.G Wiring Diagrams Workshop Manual Downloaded from www.Manualslib.com manuals search engine 8W-42 AIR CONDITIONING-HEATER
INDEX
page page
DESCRIPTION AND OPERATION
A/C OPERATION......................... 6
AIR CONDITIONING-HEATER SYSTEM

Downloaded from www.Manualslib.com manuals search engine 8W-42 AIR CONDITIONING-HEATER
INDEX
page page
DESCRIPTION AND OPERATION
A/C OPERATION......................... 6
AIR CONDITIONING-HEATER SYSTEM....... 6BLOWER MOTOR OPERATION............. 6
HELPFUL INFORMATION.................. 7
RADIATOR FAN OPERATION............... 6
DESCRIPTION AND OPERATION
AIR CONDITIONING-HEATER SYSTEM
The A/C-Heater System is powered by a by several
fuses. Fuse 10, a 15 amp fuse located in the fuse
block, is HOT in the RUN position. This fuse powers
the coil side of the A/C compressor clutch relay
located in the Power Distribution Center (PDC).
A 30 amp fuse, on circuit A16 located in the PDC,
powers the solid state radiator fan relay. This fuse is
HOT at all times. The 10 amp fuse on circuit A17
located in the PDC powers the contact side of the A/C
compressor clutch relay.
The A/C-Heater blower motor is protected by a 25
amp fuse located in cavity 7 of the fuse block. This
fuse in HOT in the RUN position only. When the
ignition switch is in the RUN position, power is sup-
plied to the fuse on circuit A22. The power leaves the
fuse on circuit C1 and goes directly to the blower
motor.
There is a 4 amp fuse located in cavity 12 of the
fuse block used for the illumination lamps in the A/C-
Heater control. The fuse is HOT at all times.
A/C OPERATION
When the A/C or the defrost switch is put in the
ON position, and the A/C cycling switch, low pressure
cut-out switch, and the high pressure switch are
CLOSED, the Powertrain Control Module (PCM)
receives a request for A/C.
After receiving this input, the PCM activates the
A/C compressor by grounding the C28 circuit on the
coil side of the A/C Compressor Clutch relay. Power
for the coil side of the relay is supplied on the bus
bar located in the Power Distribution Center (PDC).
With the coil energized, current flows from the 10
amp fuse in the PDC on circuit A17 through the
CLOSED contacts in the relay, on the C3 circuit to
the A/C compressor clutch.
The A/C compressor clutch receives this voltage
and creates a magnetic field energizing the clutch.
Ground for the coil is provided at the right headlamp
ground.
The connector at the A/C compressor has a diode
located in it. This diode is used to control the inducedvoltage resulting from the magnetic field collapsing
when the clutch is disengaged. The diode provides a
path for the voltage to protect other components and
systems.
The A/C compressor clutch relay is also used by the
PCM to disengage the compressor in a Wide Open
Throttle (W.O.T.) condition.
RADIATOR FAN OPERATION
The radiator fan system used in this vehicle uses a
solid state relay that controls the speed of the radia-
tor fan.
Power for the relay is supplied on circuit A16 This
circuit is HOT at all times and protected by a 30 amp
fuse located in the Power Distribution Center (PDC).
Ground for the coil side of the relay is controlled by
the Powertrain Control Module (PCM). When the
PCM determines the need for fan operation the PCM
supplies the ground path for circuit K173. This cir-
cuit connects to cavity 18 of the PCM connector.
From the relay circuit C25 connects to the radiator
fan motor(s). On vehicles equipped with the manual
transmission only one radiator fan is used. For vehi-
cles equipped with an automatic transmission there
are two radiator fans used.
Ground for the radiator fans is supplied on circuit
Z1.
BLOWER MOTOR OPERATION
With the ignition switch in the RUN position,
power flows from the 25 amp fuse, in cavity 7 of the
fuse block, to the blower motor. Blower motor speed
is controlled by the fan control switch located in the
instrument panel, and the resistor block.
Blower motor LOW speed operation is accom-
plished on the C4 circuit. When the control switch is
moved to the LOW speed position, current is passed
on the C7 circuit through the blower motor resistor
to the C4 circuit. It then flows through the blower
motor switch to the Z8 circuit. The Z8 circuit termi-
nates at a grounding point on the instrument panel
left center support.
The operation of the blower motor M1 and M2
speed operations is the same as the LOW speed
8W - 42 - 6 8W - 42 AIR CONDITIONING-HEATERPL

Page 113 of 256

DODGE NEON 1997 1.G Wiring Diagrams Workshop Manual Downloaded from www.Manualslib.com manuals search engine except, the C5 circuit is used for the M1 speed and
circuit C6 is used for M2 speed operation.
Blower motor HIGH speed operation is accom-
plis

Page 115 of 256

DODGE NEON 1997 1.G Wiring Diagrams Workshop Manual Downloaded from www.Manualslib.com manuals search engine 8W-43 AIRBAG SYSTEM
INDEX
page
SCHEMATICS AND DIAGRAMS........................................................... 1
DESCRIPTION AND OPERATION..

Page 116 of 256

DODGE NEON 1997 1.G Wiring Diagrams Workshop Manual Downloaded from www.Manualslib.com manuals search engine 17
FUSED
IGN.
(ST-RUN)
20
AIRBAG
CONTROL
MODULE
10A
FUSE
128FUSE10A
BLOCK
FUSE10
32 285
ST-RUN A21 RUN A22
311DATA
LINK
CONNECTOR
19 18
CCD
BUS

Page 119 of 256

DODGE NEON 1997 1.G Wiring Diagrams Workshop Manual Downloaded from www.Manualslib.com manuals search engine 8W-43 AIRBAG SYSTEM
DESCRIPTION AND OPERATION
AIRBAG CONTROL MODULE (ACM)
Two different circuits supply battery voltage from
the fuse block to

Downloaded from www.Manualslib.com manuals search engine 8W-43 AIRBAG SYSTEM
DESCRIPTION AND OPERATION
AIRBAG CONTROL MODULE (ACM)
Two different circuits supply battery voltage from
the fuse block to the Airbag Control Module (ACM),
F15 and F25. The F15 and F25 circuits are connected
to separate bus bars internal to the fuse block. Dif-
ferent circuits from the Power Distribution Center
(PDC) and ignition switch supply battery voltage to
the fuse block bus bars.
The F25 circuit supplies battery voltage to the
ACM only when the ignition switch is in the RUN
position. The F15 circuit powers the ACM when the
ignition switch is in either the START or RUN posi-
tion.
An internal bus bar in the ignition switch connects
the A1 circuit from the PDC to the A21 circuit when
the switch is either the START or RUN position. The
A21 circuit supplies battery voltage to the bus bar in
the fuse block that feeds the F15 circuit. A 30 amp
fuse in the PDC protects the A1 and A21 circuits. A
10 amp fuse in the fuse block, cavity 9, protects the
F15 circuit.
When the ignition switch is in the RUN position, it
connects the A2 circuit from the PDC to the A22 cir-
cuit. The A22 circuit supplies battery voltage to the
fuse block bus bar that feeds the F25 circuit. A 40
amp fuse in the PDC protects the A2 and A22 cir-
cuits. A 10 amp fuse in the fuse block, cavity 5, pro-
tects the F25 circuit.
Circuits D1 and D2 are connected to the CCD Bus
and the ACM. The CCD bus is used to provide com-
munications between modules and the universal data
link connector.
The ACM has a case ground and an external dedi-
cated ground, circuit Z6. The dedicated ground con-
nects to the instrument panel right center support.
AIRBAG IMPACT SENSOR
The Airbag system uses a sensor internal to the
Airbag Control Module (ACM) to detect impact. For
information regarding operation of this sensor, refer
to the appropriate group of the Service Manual.
AIRBAG SQUIB (AIRBAG IGNITER)
DRIVERS SIDE AIRBAG
Two circuits, R43 and R45, connect the ACM to the
drivers side airbag module squib (igniter) after pass-
ing through the clock spring connector. Circuit R43
from cavity 3 of the ACM 4-way connector connects
to the squib. Circuit R45 from cavity 4 of the ACM
4-way connector connects to the squib. R43 and R45
are a twisted pair of wires.
PASSENGERS SIDE AIRBAG
Two circuits, R42 and R44, connect the ACM to the
passengers side airbag module squib (igniter). Circuit
R42 from cavity 1 of the ACM 4-way connector con-
nects to the squib. Circuit R44 from cavity 2 of the
ACM 4- way connector connects to the squib. R42
and R44 are a twisted pair of wires.
Circuits R50 and R51 are connected from the ACM
to the passangers airbag. These circuits are used to
monitor the pressure switch.
AIRBAG WARNING LAMP
The Airbag Warning lamp is used to alert the oper-
ator of a problem with the Airbag system. The lamp
is illuminated when the Airbag Control Module
(ACM) grounds the R41 circuit. Refer to the appro-
priate section of the Service Manual or Diagnostic
Test Procedures Manual to diagnosis this system.
HELPFUL INFORMATION
²Check for blown fuses in the circuit that connect
to the ignition switch and those that connect to the
ACM.
²While the bus bars in the fuse block power the
ACM, they also feed additional components on sepa-
rate fuse protected circuits.
²The ACM has a case ground and an external
dedicated ground. The dedicated ground connects to
the instrument panel right center support.
PL8W - 43 AIRBAG SYSTEM 8W - 43 - 5

Page 121 of 256

DODGE NEON 1997 1.G Wiring Diagrams Workshop Manual Downloaded from www.Manualslib.com manuals search engine 8W-44 INTERIOR LIGHTING
INDEX
page
SCHEMATICS AND DIAGRAMS........................................................... 1
DESCRIPTION AND OPERATI

Load next 8 pages

Page: < prev 1-10 ... 25-32 33-40 41-48 49-56 57-64 65-72 73-80 81-88 89-96 ... 120 next >

fuel pump engine oil capacity air filter automatic transmission load capacity compression ratio