1997 DODGE NEON Door ajar

Downloaded from www.Manualslib.com manuals search engine 8W-02 COMPONENT INDEX
INDEX
page
SCHEMATICS AND DIAGRAMS........................................................... 1
DESCRIPTION AND OPERATION.......................................................... 3
Component Page
A/C Compressor Clutch.................8W-42
A/C Compressor Clutch Relay............8W-42
A/C Cycling Switch....................8W-42
A/C Heater Blower Motor................8W-42
A/C Heater Control Switch...............8W-42
A/C High Pressure Switch...............8W-42
A/C Low Pressure Switch................8W-42
ABS Hydraulic Modulator...............8W-35
ABS Pump Motor......................8W-35
ABS Pump Motor Relay.................8W-35
ABS Relay Box........................8W-35
ABS System Relay.....................8W-35
ABS Warning Lamp....................8W-35
Airbag Control Module..................8W-43
Airbag Impact Sensors..................8W-43
Airbag Warning Lamp..................8W-40
Antenna.............................8W-47
Anti-Lock Warning Lamp................8W-40
Ash Receiver Lamp....................8W-44
Automatic Shut Down Relay.............8W-30
Back-Up Lamp Switch..................8W-51
Back-Up Lamps.......................8W-51
Battery..............................8W-20
Battery Temperature Sensor.............8W-30
Blower Motor Resistor Block.............8W-42
Brake Warning Lamp...................8W-40
Brake Warning Lamp Switch.............8W-40
Camshaft Position (CMP) Sensor..........8W-30
Capacitor.........................8W-10, 20
Charge Indicator Lamp.................8W-40
Check Engine Lamp....................8W-40
Cigar Lighter Relay....................8W-41
Cigar Lighter/Power Outlet..............8W-41
Circuit Breaker.....................8W-11,62
Circuit Breaker (FB)...................8W-11
Clockspring..........................8W-41
Cluster Illumination Lamps..............8W-40
Clutch Pedal Position Switch..........8W-10, 21
Combination Flasher...................8W-52
Controller Anti-Lock Brake..............8W-35
Crankshaft Position (CKP) Sensor.........8W-30
Data Link Connector...................8W-30
Diode............................8W-15, 42
Dome Lamp..........................8W-44Component Page
Door Ajar Switches.....................8W-44
Door Jamb Switches....................8W-40
Door Lock Motors......................8W-61
Door Lock Switches....................8W-61
Door Speakers........................8W-47
Driver Side Airbag.....................8W-43
Duty Cycle Evap/Purge Solenoid..........8W-30
EGR Transducer Solenoid...............8W-30
Engine Coolant Temperature (ECT) Sensor . . 8W-30
Engine Coolant Temperature Gauge.......8W-40
Engine Oil Pressure Switch..............8W-40
Engine Starter Motor...................8W-21
Engine Starter Motor Relay..............8W-21
Fog Lamp Relay....................8W-50, 51
Fog Lamps........................8W-50, 51
Front Fog Lamp Switch.................8W-50
Fuel Gauge...........................8W-40
Fuel Injectors.........................8W-30
Fuel Pump Module.....................8W-30
Fuel Pump Relay......................8W-30
Fuse Block...........................8W-11
Fuses (FB)...........................8W-11
Fuses (PDC)..........................8W-10
Fusible Link.......................8W-20, 21
Generator............................8W-20
Glove Box Lamp And Switch.............8W-44
Ground Distribution....................8W-15
Headlamp Dimmer And Optical
Horn Switch........................8W-50
Headlamp Leveling Motors..............8W-50
Headlamp Leveling Switch...............8W-50
Headlamp Switch......................8W-50
Headlamps...........................8W-50
Heated Oxygen Sensors.................8W-30
High Beam Indicator Lamp..............8W-40
Horn Relay...........................8W-41
Horn Switches........................8W-41
Horns...............................8W-41
IAT/MAP Sensor......................8W-30
Idle Air Control (IAC) Motor.............8W-30
Ignition Coil Pack.....................8W-30
Ignition Switch........................8W-10
Immobilizer Engine Sensor..............8W-30
Immobilizer Sensor....................8W-30
PL8W - 02 COMPONENT INDEX 8W - 02 - 1

Downloaded from www.Manualslib.com manuals search engine ODOMETER
The speedometer and odometer receive their infor-
mation on the G7 circuit from the Vehicle Speed Sen-
sor (VSS) on vehicles equipped with the manual or
3±spd automatic transmission. This circuit also pro-
vides a signal to the Powertrain Control Module
(PCM).
Logic internal to the cluster steps the odometer at
a high rate to indicate the proper mileage.
SERVICE ENGINE SOON LAMP
The Service Engine Soon lamp illuminates when
the ignition switch is in the ON position and prior to
starting the vehicle. The lamp will turn off after the
vehicle is started.
If while the vehicle is running a problem is
detected in the engine control system the lamp is
illuminated. This is accomplished by the Powertrain
Control Module (PCM) grounding the G3 circuit.
SEAT BELT WARNING INDICATOR
The fasten seat belt indicator is used with the
warning chime to indicate to the operator to fasten
the seat belt. There is a switch located in the drivers
side B-pillar that is normally OPEN with the seat
belt buckled.
If the seat belt is not buckled the switch CLOSES
and a ground path is completed from the G10 circuit
to the Z1 circuit. This will illuminate the lamp in the
instrument cluster.
When the ignition switch is moved to the START
position the lamp will illuminate. Logic internal to
the instrument cluster determines the length of time.
LOW FUEL LAMP
The low fuel lamp is used to indicate to the opera-
tor that the fuel level is below a predetermined level.
This lamp is logic driven by the instrument cluster.
When the instrument cluster determines a low fuel
condition based on an input from the fuel tank gauge
level sending unit (circuit G4) it illuminates the
lamp.
HEADLAMP ON CHIME
The headlamp ON chime is used to indicate to the
operator that the headlamps or parking lamps are
ON when the drivers door is OPEN. If the lamps are
ON and the drivers door is opened, a ground path is
completed from the G26 circuit at the cluster,
through the headlamp switch, to the G16 circuit and
ending at the door ajar switch. The door ajar switch
is case grounded.
KEY-IN CHIME
The key-in chime is used to indicate to the opera-
tor that the key is in the ignition with the driversdoor OPEN. If the key is in the ignition and the driv-
ers door is OPEN, a ground path is completed from
the G26 circuit at the cluster, through the CLOSED
key-in switch, to the G16 circuit and terminating at
the door ajar switch which is case grounded.
CHARGE INDICATOR LAMP
The Charge Indicator lamp is used to alert the
operator that the charging system voltage has fallen
below the normal operating range. This circuit is con-
trolled by the Powertrain Control Module (PCM).
When the PCM determines a problem, it grounds the
G12 circuit.
AIRBAG WARNING LAMP
The Airbag Warning lamp is used to alert the oper-
ator of a problem with the Airbag system. The lamp
is illuminated when the Airbag Control Module
(ACM) grounds the R41 circuit. Refer to the appro-
priate section of the Service Manual or Diagnostic
Test Procedures Manual to diagnosis this system.
LOW OIL PRESSURE LAMP
The low oil pressure lamp is used to indicate to the
operator that the engine oil pressure has dropped
below a predetermined pressure. Power for the lamp
is provided on the G5 circuit which also powers the
other warning lamps.
When the oil pressure is low the normally OPEN
oil pressure switch CLOSES completing a path to
ground on circuit G6. The oil pressure switch is case
grounded to the engine block.
HIGH BEAM INDICATOR LAMP
The High Beam Indicator Lamp is used to indicate
to the operator that the high beam headlamps are
ON. Power is supplied to the cluster on the L3 cir-
cuit. Ground is provided on the Z3 circuit.
Circuit L3 connects from the headlamp dimmer
switch to the instrument cluster.
RIGHT AND LEFT TURN SIGNAL INDICATORS
These lamps are used to indicate to the operator
which turn signal is ON. Power for the lamps comes
from the turn signal switch. The L60 circuit is for the
right turn indicator, and the L61 circuit is used for
the left turn signal indicator. Ground for the circuits
is provided on the Z3 circuit.
BRAKE WARNING INDICATOR LAMP
The Brake Warning Indicator lamp is used to alert
the operator of a problem with the vehicles braking
system. The lamp illuminates when the ignition
switch is turned to START position to perform a self
check.
8W - 40 - 8 8W - 40 INSTRUMENT CLUSTERPL
DESCRIPTION AND OPERATION (Continued)

Downloaded from www.Manualslib.com manuals search engine 8W-44 INTERIOR LIGHTING
INDEX
page
SCHEMATICS AND DIAGRAMS........................................................... 1
DESCRIPTION AND OPERATION.......................................................... 5
Component Page
Ash Receiver Lamp...................8W-44-4
Dome Lamp.........................8W-44-2
Fuse 2 (FB).........................8W-44-4
Fuse 9 (FB).........................8W-44-4
Fuse 13 (PDC)...................8W-44-2, 3, 4
Fuse Block.........................8W-44-4
G204............................8W-44-2, 4
Glove Box Lamp And Switch..........8W-44-2, 4
Headlamp Switch..................8W-44-2, 4
Left Front Door Ajar Switch............8W-44-2
Left Rear Door Ajar Switch.............8W-44-2
Left Visor/Vanity Lamps...............8W-44-3
Map/Reading Lamps................8W-44-2, 4
Mercury Switch......................8W-44-3
Power Distribution Center.........8W-44-2, 3, 4Component Page
PRNDL Lamp.......................8W-44-4
Right Front Door Ajar Switch...........8W-44-2
Right Rear Door Ajar Switch............8W-44-2
Right Visor/Vanity Lamps..............8W-44-3
S201..............................8W-44-4
S202..............................8W-44-2
S203..........................8W-44-2, 3, 4
S210..............................8W-44-4
S220............................8W-44-2, 4
S304..............................8W-44-2
S309............................8W-44-3, 4
Trunk Lamp........................8W-44-2
Trunk Switch.......................8W-44-2
Underhood Lamp....................8W-44-3
8W - 44 - 2 8W - 44 INTERIOR LIGHTINGPL

Downloaded from www.Manualslib.com manuals search engine SWITCH AJAR
DOOR
FRONT
LEFT RIGHT
FRONT
DOOR
AJAR
SWITCH
LEFT
REAR
DOOR
AJAR
SWITCH
SWITCH AJAR
DOOR
REAR
RIGHT
S304
13FUSE10A
BATT A0
M1
18
PK
M2
20
YLM2
20
YLM2
20
YLM2
20
YL
M1
20
PK
M1
22
PK
13C103
3C105
21
M1
22
PK
1
3
M2
20
YL
M4
22
GY/BK
M4
18
GY/BK
TRUNK
SWITCH
3C309
S220
1
NO
CONNECTIONM2
22
YL
3
SWITCH HEADLAMP
M2
22
YL
Z1
22
BK
Z1
2O
BK
S202
G204
1
AND LAMP
BOX
GLOVE
M1
22
PK
M1
22
PK
S203
DOME
LAMP LAMP TRUNK
M2
20
YL
12C230
CENTER DISTRIBUTION
POWER
13 14
SWITCH
A
M23
22
YL
M2
22
YL
MAP/
READING
LAMPS
2C225
(8W-10-8)(8W-10-4)
(8W-50-2)
(8W-15-7)
(8W-15-7) (8W-10-8)(8W-10-4)
(8W-44-4)(8W-44-4)
8W - 44 - 2 8W-44 INTERIOR LIGHTINGPL-RHD
978W-1PLR04401

Downloaded from www.Manualslib.com manuals search engine 8W-44 INTERIOR LIGHTING
INDEX
page page
DESCRIPTION AND OPERATION
ASH RECEIVER LAMP.................... 6
DOME LAMP............................ 5
GLOVE BOX LAMP....................... 6
HALO LAMP/TIME DELAY RELAY............ 5
HELPFUL INFORMATION.................. 6
INTRODUCTION......................... 5MAP/READING LAMPS.................... 6
PRNDL (TRANSMISSION RANGE INDICATOR)
LAMP................................ 5
TIME OUT RELAY........................ 5
TRUNK LAMP........................... 6
UNDERHOOD LAMP...................... 6
VISOR/VANITY LAMPS.................... 5
DESCRIPTION AND OPERATION
INTRODUCTION
The courtesy lamp system is powered at all times
by the 10 amp fuse located in the Power Distribution
Center (PDC). The M1 circuit feeds the courtesy
lamps, which include the trunk lamp, underhood
lamp, visor/vanity lamps, dome lamp, time delay
relay, and the glove box lamp.
HALO LAMP/TIME DELAY RELAY
The time delay relay is used to allow a time-ON
function for the ignition switch halo lamp. Power for
the relay is received on the M1 circuit from the 10
amp fuse located in the Power Distribution Center
(PDC). This is the Ignition-Off Draw (IOD) fuse and
HOT at all times.
When a door is OPENED, or the headlamp switch
is moved to the dome lamp position, a ground path is
provided for the relay on the M23 circuit. This ener-
gizes the relay, CLOSING the contacts. When the
relay contacts are CLOSED, power is provided
through the relay to the M50 circuit.
The M50 circuit supplies current to the ignition
switch lamp in the steering column. Ground for the
lamp is provided on the Z3 circuit. This circuit
splices with the glove box lamp, the ash receiver
lamp, and the PRNDL lamp. The Z3 circuit termi-
nates at the instrument panel left center support.
Circuit M23 is also spliced with the Remote Key-
less Entry (RKE) module and the time out relay
located in the fuse block.
TIME OUT RELAY
The time out relay is located in the fuse block and
is used to control the ground path for various interior
lamps. It will also turn the lamps OFF after a spec-
ified period of time, and works with the Remote Key-
less Entry (RKE) system for illuminated entry.
Cirucit M2 connects to the relay and supplied a
ground path through the door ajar switches.Circuit M1 is used to supply battery voltage to the
relay. This circuit is proteced by a 10 amp fuse
located in cavity 13 of the Power Distribution Center
(PDC).
Circuit M32 is connected from the relay to the var-
ious interior lamps and RKE module.
PRNDL (TRANSMISSION RANGE INDICATOR)
LAMP
The PRNDL lamp receives power on the E2 circuit
from the 4 amp fuse located in the fuse block in cav-
ity 12. The fuse receives power from the headlamp
switch. Circuit E2 also powers the ash receiver lamp.
When the headlamp switch is moved to the PARK
or ON position, current flows through the fuse to the
PRNDL lamp. The ground for the lamp is supplied
on the Z3 circuit, and terminates at the instrument
panel left center support. This circuit is also spliced
in with the ash receiver lamp, the ignition switch
lamp, and the glove box lamp.
VISOR/VANITY LAMPS
The visor/vanity lamps are case-grounded, and are
operated by a switch internal to the assembly. Power
for the lamps is on the M1 circuit from the Power
Distribution Center (PDC). When the operator opens
the cover, the switch CLOSES, completing a path to
ground illuminating the lamp.
DOME LAMP
The dome lamp receives power from the 10 amp
fuse located in the Power Distribution Center on the
M1 circuit. This circuit is HOT at all times and the
Ignition-Off Draw (IOD) fuse. The ground path for
the lamp is provided in two different ways.
One way is through the door ajar switches and the
time out relay. Circuit M2 connects to all the door
ajar switches from the time out relay. The switches
are case-grounded to the body. When a door is
OPENED, the plunger in the switch CLOSES, com-
pleting a path to ground.
PL8W - 44 INTERIOR LIGHTING 8W - 44 - 5