1997 CHEVROLET CAMARO fuses

Downloaded from www.Manualslib.com manuals search engine Have each transmitter you intend to match ready for the
next steps.
To match transmitters to your vehicle:
1.
2.
3.
4.
5.
6.
7.
Turn the ignition to the RUN position, then to the
OFF position. This will disarm the Vehicle and
Content Theft-DeterrendAlarm System (if your
vehicle has this option).
Remove the RADIO fuse. This fuse is located in the
main fuse block, located on the left side
of your main
instrument panel. See “Fuses and Circuit Breakers”
in the Index.
Turn the ignition switch from the
OFF to the RUN
position three times quickly (within five seconds).
The vehicle will respond by locking the doors,
unlocking the driver’s doors and releasing the hatch.
Your transmitter is now ready
to match the vehicle.
Press and hold the LOCK and UNLOCK buttons
on
the first transmitter for 15 seconds. The vehicle will
respond as in step
3.
Repeat Step 4 for the remaining transmitters.
When you have finished matching all
of your
transmitters, replace the
RADIO fuse.
Check that all transmitters work by pressing
their buttons.
If the transmitters don’t work, or if you’d rather not match
the transmitters yourself, see your Chevrolet dealer.
Battery Replacement
Under normal use, the battery in your remote keyless
entry transmitter should last about two years.
You can tell the battery is weak if the transmitter won’t
work at the normal range in any location. If
you have to
get close
to your vehicle before the transmitter works,
it’s probably time to change the battery.
Use one battery, type CR2032, or a similar type.
2-10

Downloaded from www.Manualslib.com manuals search engine PASS-Key@ I1
Your vehicle is equipped
with the PASS-Key I1
(Personalized Automotive
Security System)
theft-deterrent system.
PASS-Key
I1 is a passive
theft-deterrent system. It works when you insert
or remove the key from
the ignition.
PASS-Key 11 uses a resistor pellet in the ignition key
that matches a decoder in your vehicle.
When the PASS-Key I1 system senses that someone is
using the wrong key, it shuts down the vehicle’s starter
and fuel systems. For about three minutes, the starter
won’t work and fuel won’t
go to the engine. If someone
tries
to start your vehicle again or uses another key
during this time, the vehicle will not start. This
discourages someone from randomly trying different
keys with different resistor pellets in an attempt to make
a match. The
ignition key must be clean and dry before it’s
inserted in the ignition
or the engine may not start. If the
engine does not start and the SECURITY light stays on
when
you try to start the vehicle, the key may be dirty or
wet. Turn the ignition
off.
Clean and dry the key. Wait about three minutes and try
again. The SECURITY light may remain
on during this
time.
If the starter still won’t work, and the key appears
to be clean and dry, wait about three minutes and try
another ignition key. At this time,
you may also want to
check the fuses
(see “Fuses and Circuit Breakers” in the
Index). If the starter won’t work with the other key, your
vehicle needs service. If your vehicle does start, the first
ignition key may be faulty. See your Chevrolet dealer or
a locksmith who can service the PASS-Key 11.
If
you accidentally use a key that has a damaged or
missing resistor pellet, the starter won’t work, and
the
SECURITY light will flash. But you don’t have to wait
three minutes before trying another ignition key.
See your Chevrolet dealer or a locksmith who can
service the PASS-Key
I1 to have a new key made.
2-17

Downloaded from www.Manualslib.com manuals search engine To program features, your vehicle must be in the
programming mode. Follow these steps:
1.
2.
3.
4.
5,
Put your key in the ignition.
Turn the ignition to the
RUN position to disarm the
Vehicle and Content Theft-DeterrentlAlarm System.
Turn the ignition to the
OFF position.
Remove
the RADIO fuse. This fuse is in the main
fuse block, located on the left side
of your
instrument panel. When the main fuse block is open,
the RADIO fuse is located in the lower right hand
corner of the fuse panel. See “Fuses and Circuit
Breakers’’ in the Index.
Turn the ignition
to the ACC position.
You should hear a chime to verify that the system is
in programming mode, If the chime sounds once,
you will be able to program Exit Lighting, Delayed
Illumination, Last
Door Closed Locking and Lockout
Prevention only. If the chime sounds twice and your
vehicle is equipped with the Vehicle and Content
Theft-Deterrent System,
you will also be able to set
Remote Keyless Entry Verification, Arming Method,
Arming Verification, Driver’s Door Delay and Shock
Sensor Enable.
Exit Lighting and Delayed Illumination
Exit Lighting: Your interior lights will come on for up
to 25 seconds when the key is removed from the
ignition switch.
Delayed Illumination: Your interior lights will come
on
and stay on for up to 25 seconds when entering the vehicle
and for up
to five seconds when leaving your vehicle.
Your vehicle comes with both features enabled. (Mode 4)
To change the factory setting, do the following:
1. Turn the courtesy la~nps on by turning the instrument
panel brightness control knob all the way up.
2. Count the number of chimes you hear. The number
of chimes tells you which mode your vehicle is
set for.
3. Turn the courtesy lamp switch to OFF.
4. Turn the courtesy lamp switch from ON to OFF until
you hear the number of chimes that correspond to the
mode selection you want.
Mode 1: Both Off
Mode 2: Delayed Illumination Only
Mode 3: Exit Lighting Only
Mode 4: Both On
2-19

Downloaded from www.Manualslib.com manuals search engine As you signal a turn or a lane change, if the arrows don’t
flash but just stay on
as you signal a turn or lane change,
a signal bulb
may be burned out and other drivers won’t
see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don’t go on at all when
you
signal a turn, check the fuse (see “Fuses and Circuit
Breakers” in the Index).
Headlamp High/Low Beam Changer
To change the headlamps
from low beam to high or
high to low, pull the turn
signal lever all the way
toward you. Then release it.
When the high beams are
on, this light on the
instrument panel also
will be on.
Windshield Wipers
You control the windshield wipers by turning the band
with
the wiper symbol on it.
For a single wiping cycle, turn the band to
MIST. Hold
it there until the wipers start, then let go. The wipers will
stop after one cycle. If you want more cycles, hold the
band on MIST longer.
2-46

Downloaded from www.Manualslib.com manuals search engine Headlamps Fuses and Circuit Breakers
The headlamp wiring is protected by a circuit breaker.
An electrical overload will cause the lamps to go on and
off, or in some cases to remain off.
If this happens, have
your headlamp wiring checked right away.
Windshield Wipers
The windshield wiper motor is protected by a circuit
breaker and a
fuse. If the motor overheats due to heavy
snow, etc., the wiper will stop until the motor cools.
If
the overload is caused by some electrical problem and
not snow, etc.,
be sure to get it fixed.
Power Windows and Other Power Options
Circuit breakers protect the power windows and other
power accessories. When the current load is too heavy,
the circuit breaker opens and closes, protecting the
circuit until the problem is fixed or goes away. The
wiring circuits in your vehicle are protected from
short circuits by a combination of fuses, circuit breakers,
and fusible thermal links in the wiring itself. This
greatly reduces the chance of fires caused by
electrical problems.
Look at the silver-colored band inside the fuse.
If the
band is broken or melted, replace the
fuse. Be sure you
replace a bad fuse with a new one of the correct size.
If you ever have a problem on the road and don’t have a
spare fuse, you can “borrow”
one of the correct value.
Just pick some feature of your vehicle that you can get
along without
-- like the radio or cigarette lighter -- and
use its fuse, if it is the size you need. Replace it as soon
as you can.
6-69

Downloaded from www.Manualslib.com manuals search engine Underhood Electrical Center Fuses
The underhood electrical center fuses are located in the
engine compartment. Open the cover to expose the fuses.
AIG CRUISE 12
IIS/\MPSI
-1
I1 IONITION
EN0 SENSOR 10
9 INJECTOR
[-1[F][-Jp]
RELAY IDENTIFICATION
L HDLP DR (r5*MPB(
115/\.psI
IljAMPSI
3 R HOLP OR
2 ACTUATORS
I ABS IGN
8
$&
7 AIP FAN
6
5 ABS VALVE F]
Fuse
ABS IGN
ACTUATORS
R HDLP DR
L HDLP DR
ABS VLV
ABS BAT
AIR PUMP
Usage
Anti-Lock Brake System
Daytime Running Lamp Module,
Headlamp
Switch, Cooling
Fan Relay, Exhaust,
Gas
Recirculation, EVAP Canister
Purge Solenoid
Headlamp Door Module
Headlamp Door Module
Brake Pressure Valve
Electronic Brake Control Module
AIR Pump (V8) Relay, Bleed
Valve and Cooling Fan
6-72

Downloaded from www.Manualslib.com manuals search engine Better Business Bureau Mediation ................... 8-9
Blizzard
...................................... 4-28
Brake Adjustment
.................................. 6-38
Fluid
....................................... 6-35
Master Cylinder
.............................. 6-35
PedalTravel
................................. 6-38
Parking
..................................... 2-38
Replacing System Parts
........................ 6-39
System Warning Light
......................... 2-79
Trailer
...................................... 4-36
Transmission Shift Interlock
.................... 2-4 1
Wear ....................................... 6-37
Brakes. Anti-Lock
............................... 4-7
Braking
........................................ 4-6
Braking in Emergencies
.......................... 4- 10
Break-In.
New Vehicle .......................... 2-23
Brightness Control
.............................. 2-54
BTSICheck
................................... 7-45
Bulb Replacement
.............................. 6-40
Canadian Roadside Assistance
.................... 8-7
Capacities and Specifications
...................... 6-74
Carbon Monoxide
.......... 2-1 1.2-42.2-43.4-29. 4-36
Care
of Your Cassette Player ...................... 3-23
Care of Your Compact Disc Player
................. 3-24
Cassette Deck Service
........................... 7-43
Cassette Storage
................................ 2-59
Cassette Tape Player
......................... 3-6. 3-9
Cassette Tape Player Care
........................ 3-23
CD Player Theft-Deterrent Feature ................. 3-20
Center High-Mounted Stoplamp Bulb Replacement
.... 6-46
BTSI ......................................... 2-41 Certification Label
.............................. 4-3
1
Chains. Safety
................................. 4-36
Chains. Tire
................................... 6-58
Changing a Flat Tire
............................. 5-29
Check Gages Light .............................. 2-88
Checking Your Restraint Systems
.................. 1-40
Chemical Paint Spotting
.......................... 6-66
Child Restraints
................................ 1-31
Securing
in a Rear Seat Position ................. 1-33
Securing
in the Right Front Seat Position .......... 1-35
Where to Put
................................ 1-31
Cigarette Lighter
............................... 2-60
Circuit Breakers and Fuses
....................... 6-69
Cleaner. Air
................................... 6-18
Cleaning Aluminum Wheels
............................ 6-65
Convertible Top
.............................. 6-64
Fabric
...................................... 6-59
Glass
....................................... 6-62
Inside
of Your Chevrolet ....................... 6-59
Instrument Panel
............................. 6-62
Leather
..................................... 6-61
Outside
of Your Chevrolet ...................... 6-63
Removable Roof Panel
......................... 6-63
Special Problems
............................. 6-60
Stains
...................................... 6-60
Tires
....................................... 6-65
Vinyl
....................................... 6-61
Wheels
..................................... 6-65
Windshield and Wiper Blades
................... 6-62
Climate Control System
........................... 3-2
Clock. Setting the
................................ 3-6
TopStrap
................................... 1-32
9-2

Downloaded from www.Manualslib.com manuals search engine Electrical Equipment. Adding .......... 2.27.3.22. 6.68
Electrical System
............................... 6-68
Engine
.................................. 6-10. 6-11
Coolant ..................................... 6-28
Coolant Heater
............................... 2-27
Coolant Level Check
.......................... 7-43
Coolant Temperature Gage
..................... 2-83
Exhaust
..................................... 2-42
Fuse Blocks
................................. 6-72
Identification
................................ 6-68
Oil Level Check
.............................. 7-43
Overheating
................................. 5- 14
Running While Parked
......................... 2-43
Specifications
................................ 6-74
Starting Your ................................ 2-26
Engine
Oil .................................... 6-12
Adding
..................................... 6- 14
Additives
................................... 6-17
Checking
................................... 6-13
Pressure Gage
................................ 2-87
Used ....................................... 6-17
When to Change
.............................. 6- 17
Etht~01
........................................ 6-5
Exhaust. Engine ................................ 2-42
Exit Lighting
............................. 2-19. 2-56
Express-Down Window .......................... 2-44
Fabric Cleaning
............................... 6-59
Fabric Protection ............................... 6-60
Fan Control. Climate Control System ................ 3-2
Feature Customization ........................... 2- 18
Driver’s Door Alarm Delay/Shock Sensor Enable ... 2-22
1
Exit Lightingmelayed Illumination ............... 2-19
Remote Keyless Entry Verification
............... 2-20
Theft-Deterrent Arming Method ................. 2-21
Theft-Deterrent Arming Verification
.............. 2-22
Fifth Gear. Manual Transmission
.............. 2-33. 2-34
Filling
Your Tank ................................ 6-6
Filter. Air
..................................... 6-19
Filter. Engine Oil
............................... 6-17
Finish Care .................................... 6-64
Finish Damage
................................. 6-66
First Gear. Automatic Transmission
................ 2-31
First
Gear. Manual Transmission .............. 2-32. 2-34
Flashers. Hazard Warning
......................... 5-2
Flat Tire. Changing ............................. 5-29
Floor Mats
.................................... 2-62
Fluids and Lubricants
............................ 1-49
Fog Lamps .................................... 2-53
Folding Rear Seatback ............................ 1-6
Foreign Countries. Fuel
........................... 6-5
Four-Way Manual Seat ........................... 1-3
French Language Manual ........................... ii
Front Console .................................. 2-58
FrontTowing .................................. 5-10
Front Turn Signal Bulb Replacement ................ 6-46
Fuel
.......................................... 6-3
FillingYourTank
.............................. 6-6
Gage ....................................... 2-89
In Foreign Countries ........................... 6-5
Fuses and Circuit Breakers ....................... 6-69
Last Door Closed LockingLockout Prevention ..... 2-20
Fourth
Gear. Manual Transmission ............ 2-33. 2-34