1996 TOYOTA TERCEL key

AX08K-01
D01644
Stop Light SwitchKey Interlock Solenoid
Shift Lock
Override Button
Shift Lock Control
Unit Assembly
BatteryMAIN
FLALTStopIgnition Switch
ACC
IGCIG
ECU-IG
Stop Light
Switch
Stop
LightSTPShift Lock
Control ECUIG ACC
Key Interlock Solenoid
KLS
+
E WIRING DIAGRAM
- AUTOMATIC TRANSAXLE (A132L)SHIFT LOCK SYSTEM
AX-23
775 Author
: Date
:
1996 TERCEL (RM440U)
SHIFT LOCK SYSTEM
LOCATION

AX08L-03
Z16063
ACCIG
KLS
+E STP
Wire Harness Side
AT8748
AT8749
AX-24
- AUTOMATIC TRANSAXLE (A132L)SHIFT LOCK SYSTEM
1996 TERCEL (RM440U)
INSPECTION
1. INSPECT SHIFT LOCK CONTROL ECU
Using a voltmeter, measure the voltage at each terminal.
HINT:
Do not disconnect the ECU connector.
TerminalMeasuring ConditionVoltage (V)
ACC - EIgnition Switch ACC10 - 14
IG - EIgnition Switch ON10 - 14
STP - EDepress brake pedal10 - 14
KLS+
- E
1 Ignition switch ACC and P position
2 Ignition switch ACC and except P position
3 (After approx 1 second)0
10 - 14
6 - 9
2. INSPECT KEY INTERLOCK SOLENOID
(a) Disconnect the solenoid connector.
(b) Using an ohmmeter, measure the resistance between ter-
minals.
Standard resistance: 12.5 - 16.5 W
If resistance value is not as specified, replace the solenoid.
(c) Apply battery positive voltage between terminals. Check
that the solenoid can be heard operating.
If the solenoid does not operate, replace the solenoid.

AX084-01
D01645
Key Interlock Solenoid
Stop Light SwitchShift Lock
Override Button
Shift Lock Control
Unit Assembly
BatteryMAIN
FLALTStopIgnition Switch
ACC
IGCIG
ECU-IG
IG
Shift Lock
Control ECUACC
Key Interlock Solenoid
KLS
+
E Stop Light
Switch
Stop
LightSTP WIRING DIAGRAM
- AUTOMATIC TRANSAXLE (A242L)SHIFT LOCK SYSTEM
AX-27
809 Author
: Date
:
1996 TERCEL (RM440U)
SHIFT LOCK SYSTEM
LOCATION

AX085-01
Z16063
ACCIG
KLS
+ESTP
Wire Harness Side
AT8748
AT8749
AX-28
- AUTOMATIC TRANSAXLE (A242L)SHIFT LOCK SYSTEM
1996 TERCEL (RM440U)
INSPECTION
1. INSPECT SHIFT LOCK CONTROL ECU
Using a voltmeter, measure the voltage at each terminal.
HINT:
Do not disconnect the ECU connector.
TerminalMeasuring ConditionVoltage (V)
ACC - EIgnition switch ACC10 - 14
IG - EIgnition switch ON10 - 14
STP - EDepressing brake pedal10 - 14
KLS+ - E
1 Ignition switch ACC and P position
2 Ignition switch ACC and except P position
3 (After approx 1 second)0
10 - 14
6 - 9
2. INSPECT KEY INTERLOCK SOLENOID
(a) Disconnect the solenoid connector.
(b) Using an ohmmeter, measure the resistance between ter-
minals.
Standard resistance: 12.5 - 16.5 W
If the resistance is not as specified, replace the solenoid.
(c) Apply battery positive voltage between terminals. Check
that the solenoid operation sound is heard.
If the operation is not as specified, replace the solenoid.

SR17T-02
- STEERINGNON-TIL T STEERING COLUMN
SR-17
1996 TERCEL (RM440U)
INSPECTION
NOTICE:
When using a vise do not overtighten it.
1. INSPECT STEERING LOCK OPERATION
Check that the steering lock mechanism operates properly.
2. IF NECESSARY, REPLACE KEY CYLINDER
(a) Place the ignition key at the ACC position.
(b) Push down the stop pin with a thin rod, and pull out the
key cylinder.
(c) Install a new cylinder.
HINT:
Make sure the ignition key is at the ACC position.
3. INSPECT IGNITION SWITCH (See page BE-1 1)
4. IF NECESSARY, REPLACE IGNITION SWITCH
(a) Remove the 2 screws.
(b) Install a new ignition switch with the 2 screws.
5. INSPECT KEY UNLOCK WARNING SWITCH
(See page BE-1 1)
6. IF NECESSARY, REPLACE KEY UNLOCK WARNING
SWITCH
(a) Remove the 2 screws.
(b) Install a new switch with the 2 screws.
7. A/T:
INSPECT KEY INTERLOCK SOLENOID
A132L A/T: (See page AX-24)
A242L A/T: (See page AX-28)
8. A/T:
IF NECESSARY, REPLACE KEY INTERLOCK SOLE-
NOID
(a) Remove the 2 screws.
(b) Install a new solenoid with the 2 screws.
9. INSPECT BEARING
Check the bearing rotation condition and check for abnormal
noise.
If the bearing is worn or damaged, replace the column tube.

SR-32
- STEERINGPOWER STEERING VANE PUMP
1996 TERCEL (RM440U)
12. INSTALL VANE PUMP PULLEY
(a) Install the woodruff key to the vane pump shaft.
(b) Using SST to stop the pulley rotating, torque the pulley set
nut.
SST 09960-10010 (09962-01000, 09963-01000)
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
13. MEASURE PS VANE PUMP ROTATING TORQUE
(See page SR-25)

BE0QS-01
I05913
Ignition Switch

Key Unlock Warning Switch
I/P J/B

Integration Relay

GAUGE Fuse
Door Courtesy Switch
BE-10- BODY ELECTRICALIGNITION SWITCH AND KEY UNLOCK WARNING
SWITCH
1032 Author
: Date
:
1996 TERCEL (RM440U)
IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH
LOCATION

BE0QT-02
N12789
Z10028
1
2 OFF
ON
N12790
N12791
- BODY ELECTRICALIGNITION SWITCH AND KEY UNLOCK WARNING
SWITCHBE-1 1
1996 TERCEL (RM440U)
INSPECTION
1. INSPECT IGNITION SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
LOCK-No continuity
ACC2 - 3Continuity
ON2 - 3 - 4
6 - 7Continuity
START1 - 2 - 4
6 - 7 - 8Continuity
If continuity is not as specified, replace the switch.
2. INSPECT KEY UNLOCK WARNING SWITCH
CONTINUITY
ConditionTester connectionSpecified condition
Switch OFF
(Key removed) -No continuity
Switch ON
(Key set)1 - 2Continuity
If continuity is not as specified, replace the switch.
3. INSPECT INTEGRATION RELAY OPERATION
(a) Connect the positive (+) lead from the battery to terminal
3.
(b) Connect the negative (-) lead from the battery to terminal
4, 7 and 8.
(c) Check the chime sounds.
(d) Disconnect the negative (-) lead from the battery to termi-
nal 8.
(e) Check that the chime stops sounding.