1996 TOYOTA T100 sensor

Downloaded from www.Manualslib.com manuals search engine DI−46
− DIAGNOSTICSENGINE (3RZ−FE)
1996 TOYOTA T100 (RM449U)
2 Check for open and short in harness and connector between ECM and heated
oxygen sensor (bank 1 sensor 1) (See page IN−26).
NG Repair or replace harness or connector.
OK
Replace heated oxygen sensor
(bank 1 sensor 1).

Downloaded from www.Manualslib.com manuals search engine FI7130
Vehicle Speed
50 ∼ 65 km/h
(31 ∼ 40 mph)
Idling
IG SW OFF
1 ∼ 3 min. 1 min. Time
(1)(2)(3)(4)
(5)
− DIAGNOSTICSENGINE (3RZ−FE)
DI−47
1996 TOYOTA T100 (RM449U)
DTC P0130 Heated Oxygen Sensor Circuit Malfunction
(Bank 1 Sensor 1)
CIRCUIT DESCRIPTION
Refer to DTC P0125 on page DI−44.
DTC No.Detection ItemDTC Detecting ConditionTrouble AreaTrouble Area
P0130
Voltage output of heated oxygen sensor remains at 0.4 V or
more or 0.55 V or less, during idling after engine is warmed
up (2 trip detection logic)Heated oxygen sensor
Fuel trim malfunction
HINT:
Sensor 1 refers to the sensor closer to the engine body.
The heated oxygen sensor’s output voltage and the short−term fuel trim value can be read using the
OBD II scan tool or TOYOTA hand−held tester.
WIRING DIAGRAM
Refer to DTC P0125 on page DI−44.
CONFIRMATION DRIVING PATTERN
(1) Connect the TOYOTA hand−held tester to the DLC3.
(2) Switch the TOYOTA hand−held tester from normal mode to check mode (See page DI−13).
(3) Start the engine and warm it up with all the accessory switches OFF.
(4) Drive the vehicle at 50 − 65 km/h (31 − 40 mph) for 1 − 3 min. to warm up the heated oxygen sensor.
(5) Let the engine idle for 1 min.
HINT:
If a malfunction exists, the MIL will light up during step (5).
NOTICE:
If the conditions in this test are not strictly followed, detection of the malfunction will not be possible.
If you do not have a TOYOTA hand−held tester, turn the ignition switch OFF after performing steps
(3) to (5), then perform steps (3) to (5) again.
DI0TK−02

Downloaded from www.Manualslib.com manuals search engine DI−48
− DIAGNOSTICSENGINE (3RZ−FE)
1996 TOYOTA T100 (RM449U)
INSPECTION PROCEDURE
1 Check for open and short in harness and connector between ECM and heated
oxygen sensor (See page IN−26).
NG Repair or replace harness or connector.
OK
2 Check for heated oxygen sensor data.
PREPARATION:
(a) Connect the OBD II scan tool or TOYOTA hand−held tester to the DLC3.
(b) Warm up the engine to normal operating temp.
CHECK:
Read heated oxygen sensor output voltage and short−term fuel trim.
HINT:
Read the values for the same bank.
RESULT:
PatternHeated oxygen sensor output voltageShort−term fuel trim
1Lean condition (Changes at 0.55 V or less)Changes at about + 20 %
2Rich condition (Changes at 0.4 V or more)Changes at about − 20 %
3Except 1 and 2
1, 2 Check fuel trim system (See page DI−55).
3

Downloaded from www.Manualslib.com manuals search engine P18349
− DIAGNOSTICSENGINE (3RZ−FE)
DI−49
1996 TOYOTA T100 (RM449U)
3 Check output voltage of heated oxygen sensor during idling.
PREPARATION:
Warm up the heated oxygen sensor with the engine at 2,500 rpm for approx. 90 sec.
CHECK:
Use the OBD II scan tool or TOYOTA hand−held tester read the output voltage of the heated oxygen sensor
during idling.
OK:
Heated oxygen sensor output voltage:
Alternates repeatedly between less than 0.4 V and more than 0.55 V (See the following table)
OK Perform confirmation driving pattern.
NG
Replace heated oxygen sensor.

Downloaded from www.Manualslib.com manuals search engine DI−50
− DIAGNOSTICSENGINE (3RZ−FE)
1996 TOYOTA T100 (RM449U)
DTC P0133 Heated Oxygen Sensor Circuit Slow
Response (Bank 1 Sensor 1)
CIRCUIT DESCRIPTION
Refer to DTC P0125 on page DI−44.
DTC No.DTC Detecting ConditionTrouble Area
P0133
Response time for heated oxygen sensor’s voltage output to
change from rich to lean, or from lean to rich, is 1 sec. or
more during idling after engine is warmed up
(2 trip detection logic)
Heated oxygen sensor
HINT:
Sensor 1 refers to the sensor closer to the engine body.
INSPECTION PROCEDURE
1 Are there any other codes (besides DTC P0133) being output?
YES Go to relevant DTC chart.
NO
Replace heated oxygen sensor.
DI0TL−01

Downloaded from www.Manualslib.com manuals search engine − DIAGNOSTICSENGINE (3RZ−FE)
DI−51
1996 TOYOTA T100 (RM449U)
DTC P0135 Heated Oxygen Sensor Heater Circuit
Malfunction (Bank 1 Sensor 1)
DTC P0141 Heated Oxygen Sensor Heater Circuit
Malfunction (Bank 1 Sensor 2)
CIRCUIT DESCRIPTION
Refer to DTC P0125 on page DI−44.
DTC No.DTC Detecting ConditionTrouble Area
P0135
P0141
When heater operates, heater current exceeds 2 A
(2 trip detection logic)Open or short in heater circuit of heated oxygen sensor
Heated oxygen sensor heater
ECM
Heater current of 0.2 A or less when heater operates
(2 trip detection logic)
HINT:
Sensor 1 refers to the sensor closer to the engine body.
Sensor 2 refers to the sensor farther away from the engine body.
WIRING DIAGRAM
Refer to DTC P0125 on page DI−44.
DI0TM−03

Downloaded from www.Manualslib.com manuals search engine BE6653
P23814
P23815
A00056
ON
For M/T
For M/THT1 (+) HT2 (+)
HT1 (+) HT2 (+)
DI−52
− DIAGNOSTICSENGINE (3RZ−FE)
1996 TOYOTA T100 (RM449U)
INSPECTION PROCEDURE
1 Check voltage between terminals HT1, HT2 of ECM connector and body ground.
PREPARATION:
(a) Remove the right cowl side trim (See page MF−50).
(b) Turn the ignition switch ON.
CHECK:
Measure voltage between terminals HT1, HT2 of ECM connec-
tor and body ground.
HINT:
Connect terminal HT1 to bank 1 sensor 1.
Connect terminal HT2 to bank 1 sensor 2.
OK:
Voltage: 9 − 14 V
OK Check and replace ECM (See page IN−26).
NG
2 Check resistance of heated oxygen sensor heater.
NG Replace heated oxygen sensor.
OK
Check and repair harness or connector be-
tween EFI main relay, heated oxygen sensor
and ECM.

Downloaded from www.Manualslib.com manuals search engine − DIAGNOSTICSENGINE (3RZ−FE)
DI−53
1996 TOYOTA T100 (RM449U)
DTC P0136 Heated Oxygen Sensor Circuit Malfunction
(Bank 1 Sensor 2)
CIRCUIT DESCRIPTION
Refer to DTC P0125 on page DI−44.
DTC No.DTC Detecting ConditionTrouble Area
P0136
Voltage output of heated oxygen sensor (bank 1 Sensor 2)
remains at 0.4 V or more or 0.5 V or less when vehicle is driv-
en at 50 km/h
(31 mph) or more after engine is warmed up
(2 trip detection logic)
Heated oxygen sensor
HINT:
Sensor 2 refers to the sensor farther away from the engine body.
WIRING DIAGRAM
Refer to DTC P0125 on page DI−44.
INSPECTION PROCEDURE
1 Are there any other codes (besides DTC P0136) being output?
YES Go to relevant DTC chart.
NO
2 Check for open and short in harness and connector between ECM and heated
oxygen sensor (See page IN−26).
NG Repair or replace harness or connector.
OK
DI0TN−02