1996 TOYOTA T100 heater

Downloaded from www.Manualslib.com manuals search engine W03128
MT:
Column Upper
Cover
Torx Screw
Steering Wheel
Pad
Steering Wheel
Steering Wheel Lower
No.3 Cover
Torx Screw
Combination Switch
(w/ Spiral Cable)
Column Lower Cover
Light Control Rheostat
Front Door Scuff
Plate Steering Wheel Lower
No.2 Cover
Steering Column Assembly
Column Hole Cover
x7
Engine Hood Release
LeverLower Finish Panel No.1Sliding w/ Shaft York
Sub−Assembly
Intermediate
Shaft Assembly
Duct Heater to
Register No.2
Cowl Side Trim Intermediate
Shaft Assembly For 2WD9.0 (90, 78 in.·lbf)35 (360, 26)
: Specified torque
N·m (kgf·cm, ft·lbf)
9.0 (90, 78 in.·lbf)
25 (260, 19)
35 (360, 26)
35 (360, 26)
35 (360, 26)
− STEERINGNON−TILT STEERING COLUMN
SR−11
1685 Author: Date:
1996 TOYOTA T100 (RM449U)

Downloaded from www.Manualslib.com manuals search engine Q02574
Matchmarks
Cap Nut SR−14
− STEERINGNON−TILT STEERING COLUMN
1996 TOYOTA T100 (RM449U)
3. A/T:
REMOVE UPPER AND LOWER COLUMN COVERS
Remove the 6 screws.
4. M/T:
REMOVE UPPER AND LOWER COLUMN COVERS
Remove the 7 screws.
5. REMOVE LOWER FINISH PANEL NO.1
(a) Remove the 2 screws and disconnect the engine hood re-
lease lever from the panel.
(b) Remove the 4 screws and front door scuff plate.
(c) Remove the clip and cowl side trim.
(d) Remove the 4 panel set bolts.
(e) Remove the light control rheostat and lock nut.
6. REMOVE DUCT HEATER TO REGISTER NO.2
Remove the screw.
7. REMOVE COMBINATION SWITCH WITH SPIRAL
CABLE
(a) Remove the 2 screws.
(b) Disconnect the connectors.
(c) Disconnect the airbag connector.
(d) Remove the 4 screws.
8. REMOVE SPIRAL CABLE
(See page BE−15)
NOTICE:
Do not disassemble the cable or apply oil to it.
9. A/T:
DISCONNECT PARKING LOCK CABLE
(a) Place the matchmarks on the cap nut and parking lock
cable.
(b) Loosen the cap nut.
(c) Disconnect the parking lock cable.

Downloaded from www.Manualslib.com manuals search engine R07644Red Mark
R07660
Torx ScrewScrew Case
− STEERINGNON−TILT STEERING COLUMN
SR−21
1996 TOYOTA T100 (RM449U)
9. INSTALL COMBINATION SWITCH WITH SPIRAL
CABLE
(a) Install the 4 screws.
(b) Connect the airbag connector.
(c) Connect the connectors.
(d) Install the 2 screws.
10. INSTALL DUCT HEATER TO REGISTER NO.2
Install the screw.
11. INSTALL LOWER FINISH PANEL NO.1
(a) Install the lock nuts and light control rheostat.
(b) Tighten the 4 panel set bolts.
(c) Install the cowl side trim and clip.
(d) Install the front door scuff plate with the 4 screws.
(e) Install the engine hood release lever with the 2 screws.
12. A/T:
INSTALL UPPER AND LOWER COLUMN COVERS
Install the 6 screws.
13. M/T:
INSTALL UPPER AND LOWER COLUMN COVERS
Install the 7 screws.
14. CENTER SPIRAL CABLE
(a) Check that the front wheels are facing straight ahead.
(b) Turn the spiral counterclockwise by hand until it becomes
harder to turn the cable.
(c) Then turn the spiral cable clockwise about 3 turns to align
the red mark.
HINT:
The spiral cable turns clockwise about 3 turns to either left or
right of the center.
15. INSTALL STEERING WHEEL
(a) Align the matchmarks on the wheel and main shaft.
(b) Torque the set nut.
Torque: 35 N·m (360 kgf·cm, 26 ft·lbf)
(c) Connect the connector.
16. INSTALL STEERING WHEEL PAD
NOTICE:
Make sure the wheel pad is installed to the specified
torque.
If the wheel pad has been dropped, or there are
cracks, dents in the case or connector, replace the
wheel pad with a new one.
When installing the wheel pad, take care that the wir-
ings do not interfere with other parts and are not
pinched between other parts.

Downloaded from www.Manualslib.com manuals search engine W03156
Column UpperParking Lock Cable
Torx Screw
Steering Wheel Lower
No.2 Cover
Control Shaft AssemblySteering Wheel
Steering Wheel
Steering Wheel Lower
No.3 Cover
Torx Screw
Combination Switch
(w/ Spiral Cable)
Column lower Cover
Light Control Rheostat
Front Door Scuff Steering Column
Assembly Control Shaft
 Locking
Column Hole
Sliding w/ Shaft York
Sub−Assembly
Lower Finish Panel No.1
Engine Hood Release Intermediate
Shaft Assembly
Register No.2 Duct Heater toPlatePad
Lever Cover
Wire
Cover
Lever AT:
For 2WD
Intermediate
Shaft Assembly
Cowl Side Trimx6
Non−reusable part35 (360, 26)
9.0 (90, 78 in.·lbf)
35 (360, 26)
35 (360, 26)
35 (360, 26)
35 (360, 26)
: Specified torque
N·m (kgf·cm, ft·lbf)
25 (260, 19)
25 (260, 19)
9.0 (90, 78 in.·lbf)
SR07C−01
− STEERINGTILT STEERING COLUMN
SR−23
1697 Author: Date:
1996 TOYOTA T100 (RM449U)
TILT STEERING COLUMN
COMPONENTS

Downloaded from www.Manualslib.com manuals search engine W03157
Cover
Pad
Plate
Lever MT:
For 2WDSteering Column AssemblySteering Wheel Steering Wheel
Steering Wheel Lower
No.3 Cover
Torx Screw
Combination Switch
(w/ Spiral Cable)
Column Lower Cover
Light Control Rheostat
Front Door Scuff x7
Sliding w/ Shaft York
Sub−Assembly
Lower Finish Panel No.1 Column Hole CoverColumn Upper
Torx Screw
Steering Wheel Lower
No.2 Cover
Intermediate
Engine Hood Release Shaft Assembly
Duct Heater to
Register No.2
Intermediate
Shaft Assembly
Cowl Side Trim 9.0 (90, 78 in.·lbf)
35 (360, 26)
: Specified torque
N·m (kgf·cm, ft·lbf)
25 (260, 19)
9.0 (90, 78 in.·lbf)
35 (360, 26)
35 (360, 26)
35 (360, 26)
SR−24
− STEERINGTILT STEERING COLUMN
1698 Author: Date:
1996 TOYOTA T100 (RM449U)

Downloaded from www.Manualslib.com manuals search engine BO0EK−02
N20330
Instrument Panel ReinforcementCenter Defroster NozzleFront Pillar Garnish Brace No. 3
Cowl Side Trim
Front Door Scuff Plate Duct Heater to
Register No. 4
Center Register
Duct Heater to Register No. 1
Instrument Panel
Combination Meter
Center Cluster Finish Panel
Steering ColumnCluster Finish Panel
Combination Switch
Steering Column Cover
Lower Center CoverGlove Compartment DoorRear Console Box Stereo Opening Cover
Steering Wheel PadRadio
Steering Wheel B
Lower Finish Panel No. 2 Brace No. 1
Brace No. 2
Side Bracket RH
Ash Tray Register No. 1
Center Cluster Finish Lower Panel
Duct Heater to Register No. 2
Glove Compartment
Door Reinforcement Lower Finish Panel No. 1I
Side Bracket LHF
G
A
H
D HA
D A A
A
AAGG
G E
E
E
E EF
F
F
F
F
E
EF B B
B
B
EE I
I
I
B BBB B
C
A
CADuct Heater to
EE
35 (360, 26)
N·m (kgf·cm, ft·lbf) : Specified torque BO−34
− BODYINSTRUMENT PANEL
1918 Author: Date:
1996 TOYOTA T100 (RM449U)
INSTRUMENT PANEL
COMPONENTS

Downloaded from www.Manualslib.com manuals search engine N15353
F Duct Heater to Register No. 3
Center Register
Mounting Bracket No. 1
Center Bracket Stay No. 2Register No. 2
Instrument PanelCup Holder Duct Heater to Register No. 5
Mounting Bracket No. 2 F
FFF
F
F
F
F
FF
F
F
F
FF
FF
V06838
A
D
GB
E
HC
F
I Code Shape Sizeø = 6 (0.24)
L = 22 (0.87)
Code Shape Size Code Shape Size
ø = 5 (0.20)
L = 14 (0.55)
ø = 5 (0.20)
L = 18 (0.71)ø = 8 (0.31)
L = 20 (0.79)
ø = 5 (0.20)
L = 16 (0.63)ø = 5 (0.20)
L = 14 (0.55) ø = 6 (0.24)
L = 18 (0.71)
− BODYINSTRUMENT PANEL
BO−35
1919 Author: Date:
1996 TOYOTA T100 (RM449U)
HINT:
Screw shapes and sizes are inndecated in the able below.
The codes (A ∼ I) correspond to those indecated on the previous pages.

Downloaded from www.Manualslib.com manuals search engine BO0EL−03
N05924
N06045
N05919
BO−36
− BODYINSTRUMENT PANEL
1996 TOYOTA T100 (RM449U)
REMOVAL
1. REMOVE FRONT PILLAR GARNISH
2. REMOVE FRONT DOOR SCUFF PLATE
3. REMOVE COWL SIDE TRIM
4. REMOVE STEERING WHEEL
(See page SR−13)
5. REMOVE STEERING COLUMN COVER
6. REMOVE HOOD LOCK RELEASE LEVER
7. REMOVE LOWER FINISH PANEL NO. 1
8. REMOVE COMBINATION SWITCH
9. REMOVE GLOVE COMPARTMENT DOOR
10. REMOVE LOWER FINISH PANEL NO. 2
11. REMOVE LOWER CENTER COVER
12. w/ Sports seat:
REMOVE REAR CONSOLE BOX
13. REMOVE CENTER CLUSTER FINISH PANEL
HINT:
Tape a screwdriver tip before use.
(a) Remove the heater control knobs.
(b) Using a screwdriver, remove the panel.
(c) Remove the radio.
(d) Remove the heater control.
14. REMOVE CENTER CLUSTER FINISH LOWER PANEL
HINT:
Tape a screwdriver tip before use.
(a) Remove the 2 screws.
(b) Using a screwdriver, remove the panel, then disconnect
the connector.
(c) Remove the stereo opening cover.
15. REMOVE CLUSTER FINISH PANEL
(a) Remove the 5 screws.
(b) Remove the combination meter.
16. REMOVE REGISTER NO. 1
17. REMOVE DUCT HEATER TO REGISTER NO. 1
18. REMOVE DUCT HEATER TO REGISTER NO. 2
19. REMOVE GLOVE COMPARTMENT DOOR RE-
INFORCEMENT
20. REMOVE BRACE NO. 1 AND NO. 2