1996 TOYOTA T100 codes

Downloaded from www.Manualslib.com manuals search engine W05582AB0118AB0119AB0069S08098W02042H00324
Spiral
Cable
ACC ON
D−D+
or
DLC1
E1
Tc
Code 11
Center Airbag
Sensor Assembly
D Squib
− DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI−375
1996 TOYOTA T100 (RM449U)
4 Check center airbag sensor assembly.
PREPARATION:
(a) Connect connector to center airbag sensor assembly.
(b) Using a service wire, connect D+ and D− on spiral cable
side of connector between spiral cable and steering
wheel pad.
(c) Connect negative (−) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(b) Clear malfunction code stored in memory.
(See page DI−365)
(c) Turn ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e) Using SST, connect terminals Tc and E1 of DLC1.
SST 09843−18020
(f) Check DTC.
OK:
DTC 11 is not output.
HINT:
Codes other than code 11 may be output at this time, but they
are not relevant to this check.
NG Replace center airbag sensor assembly.
OK

Downloaded from www.Manualslib.com manuals search engine AB0118AB0119S08098W02042
H00352
H00325
Center Airbag
Sensor Assembly
Spiral
CableD Squib
ACC ON
or
DLC1
E1
Tc
Code 11
DI−376
− DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1996 TOYOTA T100 (RM449U)
5 Check D squib.
PREPARATION:
(a) Turn ignition switch to LOCK.
(b) Disconnect negative (−) terminal cable from the battery,
and wait at least 90 seconds.
(c) Connect steering wheel pad connector.
(d) Connect negative (−) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(b) Clear malfunction code stored in memory.
(See page DI−365)
(c) Turn ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e) Using SST, connect terminals Tc and E1 of DLC1.
SST 09843−18020
(f) Check DTC.
OK:
DTC 11 is not output.
HINT:
Codes other than code 11 may be output at this time, but they
are not relevant to this check.
NG Replace steering wheel pad.
OK
From results of above inspection, malfunctioning part can now be considered normal.
To make sure of this, use simulation method to check. If malfunctioning part can not be detected
by imulation method, replace all SRS components including wire harness.

Downloaded from www.Manualslib.com manuals search engine W05582AB0118AB0119AB0069S08098W02043H00329
Center Airbag
Sensor Assembly
Spiral
Cable
ACC ON
D−D+
or
DLC1
E1Code 12
TcD Squib
− DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI−381
1996 TOYOTA T100 (RM449U)
3 Check center airbag sensor assembly.
PREPARATION:
(a) Turn ignition switch LOCK.
(b) Disconnect negative (−) terminal cable from battery.
(c) Connect connector to center airbag sensor assembly.
(d) Using a service wire, connect D+ and D− on spiral cable
side of connector between spiral cable and steering
wheel pad.
(e) Connect negative (−) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(b) Clear malfunction code stored in memory (See page
DI−365).
(c) Turn ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e) Using SST, connect terminals Tc and E1 of DLC1.
SST 09843−18020
(f) Check DTC.
OK:
DTC 12 is not output.
HINT:
Codes other than code 12 may be output at this time, but they
are not relevant to this check.
NG Replace center airbag sensor assembly.
OK

Downloaded from www.Manualslib.com manuals search engine AB0118 AB0119
S08098W02043
H00352
H00330
Center Airbag
Sensor Assembly
Spiral
CableD Squib
ACC ON
or
DLC1
E1
Tc
Code 12
DI−382
− DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1996 TOYOTA T100 (RM449U)
4 Check D squib.
PREPARATION:
(a) Turn ignition switch to LOCK.
(b) Disconnect negative (−) terminal cable from the battery,
and wait at least 90 seconds.
(c) Connect steering wheel pad connector.
(d) Connect negative (−) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(b) Clear malfunction code stored in memory (See page
DI−365).
(c) Turn ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e) Using SST, connect terminals Tc and E1 of DLC1.
SST 09843−18020
(f) Check DTC.
OK:
DTC 12 is not output.
HINT:
Codes other than code 12 may be output at this time. but they
are not relevant to this check.
NG Replace steering wheel pad.
OK
From results of above inspection, malfunctioning part can now be considered normal.
To make sure of this, use simulation method to check.

Downloaded from www.Manualslib.com manuals search engine AB0118AB0119AB0069S08098
W05582
W02044H00338
Spiral
CableD Squib
ACC ON
D−D+
or
DLC1
E1
Tc
Code 14
Center Airbag
Sensor Assembly
DI−386
− DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1996 TOYOTA T100 (RM449U)
3 Check center airbag sensor assembly.
PREPARATION:
(a) Connect connector to center airbag sensor assembly.
(b) Using a service wire, connect D+ and D− on spiral cable
side of connector between spiral cable and steering
wheel pad.
(c) Connect negative (−) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(b) Clear malfunction code stored in memory (See page
DI−365).
(c) Turn ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e) Using SST, connect terminals Tc and E1 of DLC1.
SST 09843−18020
(f) Check DTC.
OK:
DTC 14 is not output.
HINT:
Codes other than code 14 may be output at this time, but they
are relevant to this check.
NG Go to step 7.
OK

Downloaded from www.Manualslib.com manuals search engine AB0118AB0119S08098W02044
H00352
H00339
Center Airbag
Sensor Assembly
D Squib
Spiral
Cable
ACC ON
or
DLC1
E1
Tc
Code 14
− DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI−387
1996 TOYOTA T100 (RM449U)
4 Check D squib.
PREPARATION:
(a) Turn ignition switch to LOCK.
(b) Disconnect negative (−) terminal cable from the battery,
and wait at least 90 seconds.
(c) Connect steering wheel pad connector.
(d) Connect negative (−) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(b) Clear malfunction code stored in memory (See page
DI−365).
(c) Turn ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e) Using SST, connect terminals Tc and E1 of DLC1.
SST 09843−18020
(f) Check DTC.
OK:
DTC 14 is not output.
HINT:
Codes other than code 14 may be output at this time, but they
are not relevant to this check.
NG Replace steering wheel pad.
OK
From results of above inspection, malfunctioning part can now be considered normal.
To make sure of this, use simulation method to check.

Downloaded from www.Manualslib.com manuals search engine AB0118
R13006AB0069
AB0119W02044
H01002
H01140
D Squib
Spiral
CableAirbag
Sensor
Assembly
ON
D+
DLC1 DTC 14ACC
or D−
Tc E1
− DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI−389
1996 TOYOTA T100 (RM449U)
7 Check center airbag sensor assembly.
CHECK:
(a) Turn ignition switch to ACC or ON and wait at least 20 se-
conds.
(b) Clear malfunction code stored in memory (See page
DI−365).
(c) Turn ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e) Using SST, connect terminals Tc and E
1 of DLC1.
SST 09843−18020
(f) Check DTC.
OK:
DTC 14 is not output.
HINT:
Codes other than code 14 may be output at this time, but they
are not relevant to this check.
NG Replace center airbag sensor assembly.
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check.

Downloaded from www.Manualslib.com manuals search engine AB0118AB0119S08098H00316
H00350
H00340
Center Airbag
Sensor Assembly
D Squib
Spiral
Cable
ACC ON
or
DLC1
E1
Tc
Code 15
DI−392
− DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1996 TOYOTA T100 (RM449U)
4 Check center airbag sensor assembly.
PREPARATION:
(a) Connect center airbag assembly connector.
(b) Connect negative (−) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(b) Clear malfunction code stored in memory (See page
DI−365).
(c) Turn ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e) Using SST, connect terminals Tc and E1 of DLC1.
SST 09843−18020
(f) Check DTC.
OK:
DTC 15 is not output.
HINT:
Codes other than code 15 may be output at this time, but they
are not relevant to this check.
NG Replace center airbag sensor assembly.
OK
From results of above inspection, malfunction part can now be considered normal.
To make sure of this, use simulation method to check.
5 Check connection of center airbag sensor assembly connector.
NG Repair.
OK