1996 TOYOTA T100 radio

Downloaded from www.Manualslib.com manuals search engine BE1PK−02
− BODY ELECTRICALANTENNA
BE−81
1881 Author: Date:
1996 TOYOTA T100 (RM449U)
ANTENNA
INSPECTION
1. INSPECT ANTENNA MOTOR
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (−) lead to terminal 2.
(b) Check that the motor turns (moves upward).
NOTICE:
These tests must be done quickly (within 3 − 5 seconds) to
prevent the coil from burning out.
(c) Then, reverse the polarity, check that the motor turns the
opposite way (moves downward).
NOTICE:
These tests must be done quickly (within 3 − 5 seconds) to
prevent the coil from burning out.
2. INSPECT ANTENNA MOTOR CONTROL RELAY CIR-
CUIT
Disconnect the connector from the relay and inspect the con-
nector on wire harness side, as shown in the chart below.
Tester connectionConditionSpecified condition
2 − 3ConstantContinuity
6 − GroundConstantContinuity
1 − GroundConstantBattery positive voltage
4 − GroundIgnition switch LOCK or ACCNo voltage
4 − GroundIgnition switch ONBattery positive voltage
5 − GroundIgnition switch LOCKNo voltage
5 − GroundIgnition switch ACC or ONBattery positive voltage
7 − GroundIgnition switch LOCKNo voltage
7 − GroundIgnition switch ACC or ON
(Radio switch and cassette OFF)No voltage
7 − GroundIgnition switch ACC or ON
(Radio switch or cassette ON)Battery positive voltage
8 − GroundIgnition switch LOCKNo voltage
If circuit is as specified, replace the relay.

Downloaded from www.Manualslib.com manuals search engine BE1PL−02
BE4671
Antenna Nut
BE5781
BE5780
BE4674
Twist BE−82
− BODY ELECTRICALANTENNA
1996 TOYOTA T100 (RM449U)
REPLACEMENT
1. REMOVE ANTENNA ROD
HINT:
Perform this operation with negative (−) cable connected to the
battery terminal.
(a) Turn the ignition switch to ”LOCK” position.
(b) Remove the antenna nut.
(c) Press the ”AM” buttons on the radio receiver, and simulta-
neously turn the ignition switch to ”ACC” position.
HINT:
The rod will extend fully and be released from the motor
antenna.
After removing the antenna rod, leave the ignition switch
as ”ACC”.
NOTICE:
To prevent body damage when the antenna rod is released,
hold the rod while it comes out.
2. INSTALL ANTENNA ROD
(a) Insert the cable of the rod until it reaches the bottom.
HINT:
When inserting the cable, the teeth on the cable must face to-
ward the front of the vehicle.
(b) Wind the cable to retract the rod by turning the ignition
switch to ”LOCK” position.
HINT:
If the ignition switch is already in ”LOCK” position, perform
step 1 (c) first, then turn the ignition switch to ”ACC” posi-
tion.
In case the cable is not wound, twist it as shown in the il-
lustration.
Even if the rod has not retracted fully, install the antenna
nut and inspect the antenna rod operation. It will finally re-
tract fully.
(c) Inspect the antenna rod operation by pushing the radio
wave band select buttons.

Downloaded from www.Manualslib.com manuals search engine BO0EK−02
N20330
Instrument Panel ReinforcementCenter Defroster NozzleFront Pillar Garnish Brace No. 3
Cowl Side Trim
Front Door Scuff Plate Duct Heater to
Register No. 4
Center Register
Duct Heater to Register No. 1
Instrument Panel
Combination Meter
Center Cluster Finish Panel
Steering ColumnCluster Finish Panel
Combination Switch
Steering Column Cover
Lower Center CoverGlove Compartment DoorRear Console Box Stereo Opening Cover
Steering Wheel PadRadio
Steering Wheel B
Lower Finish Panel No. 2 Brace No. 1
Brace No. 2
Side Bracket RH
Ash Tray Register No. 1
Center Cluster Finish Lower Panel
Duct Heater to Register No. 2
Glove Compartment
Door Reinforcement Lower Finish Panel No. 1I
Side Bracket LHF
G
A
H
D HA
D A A
A
AAGG
G E
E
E
E EF
F
F
F
F
E
EF B B
B
B
EE I
I
I
B BBB B
C
A
CADuct Heater to
EE
35 (360, 26)
N·m (kgf·cm, ft·lbf) : Specified torque BO−34
− BODYINSTRUMENT PANEL
1918 Author: Date:
1996 TOYOTA T100 (RM449U)
INSTRUMENT PANEL
COMPONENTS

Downloaded from www.Manualslib.com manuals search engine BO0EL−03
N05924
N06045
N05919
BO−36
− BODYINSTRUMENT PANEL
1996 TOYOTA T100 (RM449U)
REMOVAL
1. REMOVE FRONT PILLAR GARNISH
2. REMOVE FRONT DOOR SCUFF PLATE
3. REMOVE COWL SIDE TRIM
4. REMOVE STEERING WHEEL
(See page SR−13)
5. REMOVE STEERING COLUMN COVER
6. REMOVE HOOD LOCK RELEASE LEVER
7. REMOVE LOWER FINISH PANEL NO. 1
8. REMOVE COMBINATION SWITCH
9. REMOVE GLOVE COMPARTMENT DOOR
10. REMOVE LOWER FINISH PANEL NO. 2
11. REMOVE LOWER CENTER COVER
12. w/ Sports seat:
REMOVE REAR CONSOLE BOX
13. REMOVE CENTER CLUSTER FINISH PANEL
HINT:
Tape a screwdriver tip before use.
(a) Remove the heater control knobs.
(b) Using a screwdriver, remove the panel.
(c) Remove the radio.
(d) Remove the heater control.
14. REMOVE CENTER CLUSTER FINISH LOWER PANEL
HINT:
Tape a screwdriver tip before use.
(a) Remove the 2 screws.
(b) Using a screwdriver, remove the panel, then disconnect
the connector.
(c) Remove the stereo opening cover.
15. REMOVE CLUSTER FINISH PANEL
(a) Remove the 5 screws.
(b) Remove the combination meter.
16. REMOVE REGISTER NO. 1
17. REMOVE DUCT HEATER TO REGISTER NO. 1
18. REMOVE DUCT HEATER TO REGISTER NO. 2
19. REMOVE GLOVE COMPARTMENT DOOR RE-
INFORCEMENT
20. REMOVE BRACE NO. 1 AND NO. 2