1996 TOYOTA T100 transmission fluid

Downloaded from www.Manualslib.com manuals search engine AT1993
Z14775
A340E
Z14776
A340F
Z14777
A340F
Z14778
A340E
A
B
B A A
AB
B
− AUTOMATIC TRANSMISSIONVALVE BODY ASSEMBLY
AT−13
1354 Author: Date:
1996 TOYOTA T100 (RM449U)
4. REMOVE SHIFT SOLENOID VALVE
(a) Disconnect the connectors from the solenoid valves.
(b) Remove the 3 solenoid valve mounting bolts.
(c) Remove the 3 solenoid valves.
(d) Remove the 3 O−rings from the solenoid valves.
5. A340E:
REMOVE OIL STRAINER
NOTICE:
Be careful as some fluid will come out with the oil strainer.
(a) Separate the solenoid wire from the oil strainer.
(b) Remove the 3 bolts, oil strainer and 2 gaskets.
6. A340F:
REMOVE OIL STRAINER
NOTICE:
Be careful as some fluid will come out with the oil strainer.
(a) Remove the 11 bolts and oil strainer from the oil strainer
case.
(b) Remove the 2 gaskets from the oil strainer.
(c) Remove the 5 bolts and oil strainer case.
Torque: 10 N·m (100 kgf·cm, 7 ft·lbf)
7. A340E:
REMOVE OIL PIPE
Pry up both pipe ends with a large screwdriver and remove the
2 pipes.

Downloaded from www.Manualslib.com manuals search engine AT1362
Seal Breadth
2 − 3 mm (0.08 − 0.12 in.)
Q07625
AT−16
− AUTOMATIC TRANSMISSIONVALVE BODY ASSEMBLY
1357 Author: Date:
1996 TOYOTA T100 (RM449U)
16. INSTALL OIL PAN
(a) A340E:
Install the 4 magnets.
(b) A340F:
Install the 6 magnets.
(c) Remove any packing material and be careful not to drop
oil on the contacting surfaces of the transmission case
and oil pan.
(d) Apply FIPG to the oil pan, as shown in the illustraiton.
FIPG: Part No. 08826−00090, THREE BOND 1281 or
equivalent
(e) Install the oil pan with the 19 bolts.
Torque: 7.4 N·m (75 kgf·cm, 65 in.·lbf)
17. INSTALL DRAIN PLUG
Torque: 20 N·m (205 kgf·cm, 15 ft·lbf)
18. FILL FLUID AND CHECK FLUID

Downloaded from www.Manualslib.com manuals search engine D00842
AT02C−01
AT−32
− AUTOMATIC TRANSMISSIONAUTOMATIC TRANSMISSION UNIT (A340E)
1996 TOYOTA T100 (RM449U)
INSTALLATION
1. CHECK TORQUE CONVERTER CLUTCH INSTALLA-
TION
Using calipers and a straight edge, measure the distance from
the installed surface of the transmission housing to the installed
surface of the torque converter clutch.
Correct distance:
More than 31.75 mm (1.2500 in.) for 3RZ−FE
More than 17.95 mm (0.7067 in.) for 5VZ−FE
2. INSTALL TRANSMISSION
Installation is in the reverse order of removal (See page
AT−28).
HINT:
After installation, adjust the shift lever position (See page
DI−265).
Fill ATF and check the fluid level (See page DI−265).

Downloaded from www.Manualslib.com manuals search engine D00842
AT02F−01
− AUTOMATIC TRANSMISSIONAUTOMATIC TRANSMISSION UNIT (A340F)
AT−37
1996 TOYOTA T100 (RM449U)
INSTALLATION
1. CHECK TORQUE CONVERTER CLUTCH INSTALLA-
TION
Using calipers and a straight edge, measure from the installed
surface of the transmission housing.
Correct distance: More than 17.95 mm (0.7067 in.)
2. INSTALL TRANSMISSION
Installation is in the reverse order of removal (See page
AT−34).
HINT:
After installation, adjust the shift lever position (See page
DI−265).
Fill ATF and check fluid level (See page DI−265).