1996 TOYOTA T100 oil type

Downloaded from www.Manualslib.com manuals search engine P00300
OhmmeterContinuity
P00299
No continuity
Ohmmeter
Z10079
Length Brush Holder Side
Field Frame Side
Length
ST0019
− STARTING (5VZ−FE)STARTER
ST−7
1996 TOYOTA T100 (RM449U)
7. INSPECT FIELD COIL FOR OPEN CIRCUIT
Using an ohmmeter, check that there is continuity between the
lead wire and field coil brush lead.
If there is no continuity, replace the field frame.
8. INSPECT THAT FIELD COIL IS NOT GROUNDED
Using an ohmmeter, check that there is no continuity between
the field coil end and field frame.
If there is continuity, repair or replace the field frame.
9. INSPECT BRUSH LENGTH
Using vernier calipers, measure the brush length.
Standard length:
1.2 kW, 1.4 kW type: 15.5 mm (0.610 in.)
1.8 kW type: 15.0 mm (0.591 in.)
Minimum length:
1.2 kW, 1.4 kW type: 10.0 mm (0.394 in.)
1.8 kW type: 9.0 mm (0.354 in.)
If the length is less than minimum, replace the brush holder and
field frame.
10. INSPECT BRUSH SPRING LOAD
Take the pull scale reading the instant the brush spring sepa-
rates from the brush.
Standard installed load:
1.2 kW type
13.7 − 19.6 N (1.40 − 2.00 kgf, 3.1 − 4.4 lbf)
1.4 kW type
17.6 − 23.5 N (1.80 − 2.40 kgf, 4.0 − 5.3 lbf)
1.8 kW type
21.5 − 27.5 N (2.20 − 2.80 kgf, 4.9 − 6.2 lbf)

Downloaded from www.Manualslib.com manuals search engine (kgf/cm2)
=
100 kgf
Ram diameter (cm)
2
2
2Ram diameter (in.) (psi)
=
x 3.14 (π) x 3.14 (π)
2
(kPa) = (kgf/cm
2) x 98.1
(kPa) = (psi) x 6.9221 lbf
P25601
SST
P25591
ST−12
− STARTING (5VZ−FE)STARTER
1996 TOYOTA T100 (RM449U)
NOTICE:
Check the diameter of the hand press ram. Then calculate
the gauge pressure of the press when
981 N (100 kgf, 221 lbf) of force is applied.
Gauge pressure:
If the contact plate is not pressed down with the specified pres-
sure, the contact plate may tilt due to coil deformation or the
tightening of the nut.
(b) Using SST, tighten the nuts to the specified torque.
SST 09810−38140
Torque: 17 N·m (173 kgf·cm, 12 ft·lbf)
NOTICE:
If the nut is over tightened, it may cause cracks on the in-
side of the insulator.
6. CLEAN CONTACT SURFACES OF CONTACT PLATE
AND PLUNGER
Clean the contact surfaces of the remaining contact plate and
plunger with a dry shop rag.
7. REINSTALL MAGNETIC SWITCH END COVER
Install the plunger, new gasket, end cover and lead clamp (1.8
kW type) with the 3 bolts.
Torque:
1.2 kW, 1.4 kW type: 2.5 N·m (25 kgf·cm, 22 in.·lbf)
1.8 kW type: 3.6 N·m (35 kgf·cm, 30 in.·lbf)

Downloaded from www.Manualslib.com manuals search engine ST03C−03
P20438Battery
Terminal 50Terminal C
P20449
P20448
P20447
Terminal 30
Ammeter
ST−14
− STARTING (5VZ−FE)STARTER
1996 TOYOTA T100 (RM449U)
TEST
NOTICE:
These tests must be done within 3 to 5 seconds to avoid
burning out the coil.
1. DO PULL−IN TEST
(a) Disconnect the field coil lead wire from terminal C.
(b) Connect the battery to the magnetic switch as shown.
Check that the clutch pinion gear moves outward.
2. DO HOLD−IN TEST
With battery connected as above with the clutch pinion gear
out, disconnect the negative (−) lead from terminal C. Check
that the pinion gear remains out.
3. INSPECT CLUTCH PINION GEAR RETURN
Disconnect the negative (−) lead from the switch body.
Check that the clutch pinion gear returns inward.
4. DO NO−LOAD PERFORMANCE TEST
(a) Connect the battery and ammeter to the starter as shown.
(b) Check that the starter rotates smoothly and steadily with
the pinion gear moving out. Check that the ammeter
reads the specified current.
Specified current:
1.2 kW, 1.4 kW type
90 A or less at 11.5 V
1.8 kW type
100 A or less at 11.5 V

Downloaded from www.Manualslib.com manuals search engine AT0ZJ−01
Q07625
AT3168SST
AT0103
AT−12
− AUTOMATIC TRANSMISSIONVALVE BODY ASSEMBLY
1353 Author: Date:
1996 TOYOTA T100 (RM449U)
VALVE BODY ASSEMBLY
ON−VEHICLE REPAIR
CAUTION:
When working with FIPG material, you must observe the
followings.
Using a razor blade and a gasket scraper, remove all
oil FIPG material from the gasket surfaces.
Remove all loose material to thoroughly clean all
components.
Clean both sealing surfaces with a non−residue sol-
vent.
Apply FIPG in an approx. 1 mm (0.04 in.) wide bead
along the sealing surface.
Parts must be assembled within 10 minutes of ap-
plication. Otherwise, the FIPG material must be re-
moved and reapplied.
1. REMOVE DRAIN PLUG AND DRAIN ATF
Torque: 20 N·m (205 kgf·cm, 15 ft·lbf)
2. REMOVE OIL PAN
NOTICE:
Some fluid will remain in the oil pan.
(a) Remove the 19 bolts.
Torque: 7.4 N·m (75 kgf·cm, 65 in.·lbf)
(b) Install the blade of SST between the transmission case
and oil pan, cut off applied sealer, and remove the oil pan.
SST 09032−00100
NOTICE:
When removing the oil pan, be careful not to damage the oil
pan flange.
3. EXAMINE PARTICLES IN PAN
Remove the magnets and use them to collect steel particles.
Carefully look at the foreign matter and particles in the pan and
on the magnets to anticipate the type of wear you will find in the
transmission.
Steel (magnetic)......bearing, gear and clutch plate wear
Brass (non−magnetic) ...... bushing wear

Downloaded from www.Manualslib.com manuals search engine R12169
SST
FA1083
SST
R04344
Less than 5 mm (0.20 in.) SA−44
− SUSPENSION AND AXLEFRONT DIFFERENTIAL REAR OIL SEAL (4WD)
1996 TOYOTA T100 (RM449U)
8. INSTALL COMPANION FLANGE
(a) Using SST, install the companion flange on the drive pin-
ion.
SST 09950−30010
(b) Apply light coat of hypoid gear oil on threads of a new
companion flange nut.
(c) Using SST to hold the flange, torque the nut.
SST 09330−00021
Torque: 108 N·m (1,100 kgf·cm, 80 ft·lbf)
9. ADJUST DRIVE PINION PRELOAD
(See page SA−57)
10. STAKE DRIVE PINION NUT
11. INSTALL FRONT PROPELLER SHAFT
(See page PR−16)
12. FILL DIFFERENTIAL WITH HYPOID GEAR OIL
Torque:
Drain plug: 49 N·m (500 kgf·cm, 36 ft·lbf)
Filler plug: 39 N·m (400 kgf·cm, 29 ft·lbf)
Oil type: Hypoid gear oil API GL−5
Recommended oil viscosity: SAE 75W−90
Capacity: 1.86 liters (1.97 US qts, 1.64 lmp. qts)
13. INSTALL ENGINE UNDER COVER

Downloaded from www.Manualslib.com manuals search engine SA0I7−02
RA10720 − 5 mm (0 − 0.20 in.) OilFiller Hole SA−154
− SUSPENSION AND AXLEREAR DIFFERENTIAL CARRIER
1996 TOYOTA T100 (RM449U)
INSTALLATION
1. INSTALL NEW GASKET TO AXLE HOUSING
2. INSTALL DIFFERENTIAL CARRIER ASSEMBLY
Install the differential carrier assembly in the axle housing.
Torque: 73 N·m (740 kgf·cm, 54 ft·lbf)
3. INSTALL PROPELLER SHAFT
2WD: See page PR−9
4WD: See page PR−16
4. INSTALL REAR AXLE SHAFTS
(See page SA−135)
5. FILL DIFFERENTIAL WITH DIFFERENTIAL OIL
Torque:
Drain plug: 49 N·m (500 kgf·cm, 39 ft·lbf)
Filler plug: 39 N·m (400 kgf·cm, 29 ft·lbf)
Oil type: Hypoid gear oil API GL−5
Recommended oil viscosity:
Above −18°C (0°F) SAE 90
Below −18°C (0°F) SAE 80W or 80W − 90
Capacity: 2.35 liters (2.22 US qts, 2.67 lmp.qts)