Page 1128 of 2062
Downloaded from www.Manualslib.com manuals search engine LU−4
− LUBRICATION (3RZ−FE)OIL AND FILTER
1996 TOYOTA T100 (RM449U)
3. REFILL WITH ENGINE OIL
(a) Clean and install the oil drain plug with a new gasket.
Torque:25 N·m (250 kgf·cm, 18 ft·lbf)
(b) Fill with fresh engine oil.
Oil capacity
Drain and refill
w/ Oil filter change
5.3 liters (5.6 US qts, 4.7 lmp. qts)
w/o Oil filter change
5.0 liters (5.3 US qts, 4.4 lmp. qts)
Dry fill
6.0 liters (6.3 US qts, 5.3 lmp. qts)
(c) Reinstall the oil filler cap.
4. START ENGINE AND CHECK FOR LEAKS
5. RECHECK ENGINE OIL LEVEL
Page 1138 of 2062

Downloaded from www.Manualslib.com manuals search engine LU0817
Recommended Viscosity (SAE):
10W−30
5W−30 PREFERRED
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
LU033−04
P20966SST
P20969
Oil Pressure Gauge
− LUBRICATION (5VZ−FE)OIL AND FILTER
LU−1
1121 Author: Date:
1996 TOYOTA T100 (RM449U)
OIL AND FILTER
INSPECTION
1. CHECK ENGINE OIL QUALITY
Check the oil for deterioration, entry of water, discoloring or thin-
ning.
If oil quality is visibly poor, replace it.
Oil grade:
API grade SH Energy−Conserving II or ILSAC multi-
grade engine oil.
SAE 5W−30 is the bset choise for your vehicle, for
good fuel economy, and good starting in cold
weather.
2. CHECK ENGINE OIL LEVEL
The oil level should be between the ”L” and ”F” marks on the dip-
stick.
3. CHECK OIL LEVEL
The oil level should be between the ”L” and ”F” marks on the lev-
el gauge. If low, check for leakage and add oil up to the ”F” mark.
If low, check for leakage and add oil up to the ”F” mark.
When inserting the oil dipstick, insert the curved tip of the
dipstick facing the same direction as the curve of the
guide.If the dipstick gets caught while inserting it, do not
force it in. Reconfirm the direction of the dipstick.
4. REMOVE OIL PRESSURE SWITCH
Using SST, remove the oil pressure switch.
SST 09816−30010
5. INSTALL OIL PRESSURE GAUGE
6. START ENGINE
Start the engine and warm it up to normal operating tempera-
ture.
7. CHECK OIL PRESSURE
Oil pressure:
At idle speed
29 kPa (0.3 kgf/cm
2, 4.3 psi) or more
At 3,000 rpm
245 − 520 kPa (2.5 − 5.3 kgf/cm
2, 36 − 75 psi)
8. REMOVE OIL PRESSURE GAUGE
Page 1141 of 2062
Downloaded from www.Manualslib.com manuals search engine LU−4
− LUBRICATION (5VZ−FE)OIL AND FILTER
1996 TOYOTA T100 (RM449U)
3. FILL WITH ENGINE OIL
(a) Clean and install the oil drain plug with a new gasket.
(b) Fill the engine with new oil.
Oil capacity
ItemCapacity
liters (US qts, lmp. qts)
Drain and refill
w/ Oil filter change 2WD
4WD
w/o Oil filter change 2WD
4WD
Dry fill 2WD
4WD
5.2 (5.5, 4.6)
4.7 (5.0, 4.1)
4.9 (5.2, 4.3)
4.4 (4.7, 3.9)
5.9 (6.2, 5.2)
5.5 (5.8, 4.8)
(c) Reinstall the oil filler cap.
4. START ENGINE AND CHECK FOR LEAKS
5. RECHECK ENGINE LEVEL
Page 1662 of 2062

Downloaded from www.Manualslib.com manuals search engine BR096−01
R08165
Z04448
R08166
− BRAKEFRONT BRAKE PAD (4WD)
BR−25
1996 TOYOTA T100 (RM449U)
REPLACEMENT
1. REMOVE FRONT WHEEL
2. INSPECT PAD LINING THICKNESS
Check the pad thickness and replace pads if not within specifi-
cation.
Minimum thickness: 1.0 mm (0.039 in.)
3. REMOVE THESE PARTS:
Clip
2 pins
Anti−rattle spring
2 pads
4 anti−squeal shims
NOTICE:
The anti−rattle spring can be used again provided that they
have sufficient rebound, no deformation, cracks or wear,
and have had all rust, dirt and foreign particles cleaned off.
4. CHECK DISC THICKNESS AND RUNOUT
(See page BR−36)
5. INSTALL NEW PADS
NOTICE:
When replacing worn pads, the anti−squeal shims must be
replaced together with the pads.
(a) Draw out a small amount of brake fluid from the reservoir.
(b) Press in the pistons with a hammer handle or equivalent.
HINT:
Always change the pad on one wheel at a time as there
is a possibility of the opposite piston flying out.
If the piston is difficult to push in, loosen the bleeder plug
and push in the piston while letting some brake fluid es-
cape.
(c) Install the 4 anti−squeal shims to new pads.
HINT:
Apply disc brake grease to the inner anti−squeal shims (See
page BR−24).
(d) Install the 2 pads.
NOTICE:
Do not allow oil or grease on the rubbing face.
6. INSTALL ANTI−RATTLE SPRING AND 2 PINS
7. INSTALL CLIP
Page 1771 of 2062

Downloaded from www.Manualslib.com manuals search engine SR07Y−01
F00854
SSTSST
Oil Seal
SST Vinyl Tape
W03126
Rack Teeth End
SST SR−64
− STEERINGPOWER STEERING GEAR (2WD)
1996 TOYOTA T100 (RM449U)
REASSEMBLY
NOTICE:
When using a vise, do not overtighten it.
1. COAT WITH POWER STEERING FLUID OR MOLYBDE-
NUM DISULFIDE LITHIUM BASE GREASE (See page
SR−54)
2. INSTALL OIL SEAL
(a) Coat a new oil seal lip with power steering fluid.
(b) Using SST, press in the oil seal.
SST 09950−60010 (09951−00240, 09951−00430,
09952−06010), 09950−70010 (09951−07360)
NOTICE:
Make sure to install the oil seal facing the correct
direction.
Take care that the oil seal does not get reversed as
you install it.
3. INSTALL STEERING RACK
HINT:
If necessary, scrape the burrs off the rack teeth end then clean
and burnish before installation.
(a) Make sure that the tube hole is not clogged with grease.
HINT:
If the tube hole is clogged, the pressure inside the boot will
change after it is assembled and the steering wheel turned.
(b) Install SST to the rack.
SST 09631−33010
(c) Coat SST with power steering fluid.
(d) Insert the rack into the rack housing.
NOTICE:
Be careful not to damage the oil seal lip.
(e) Remove the SST.
Page 1772 of 2062

Downloaded from www.Manualslib.com manuals search engine R13021
Vinyl Tape
R15248
Wire
SST
Cylinder End
Stopper
R04609
SST
R13031
Vinyl Tape
W03369
SST
Oil Seal
− STEERINGPOWER STEERING GEAR (2WD)
SR−65
1996 TOYOTA T100 (RM449U)
4. INSTALL RACK BUSHING AND CYLINDER END
STOPPER
(a) To prevent oil seal lip damage, wind vinyl tape on the
steering rack end, and apply power steering fluid.
(b) Coat a new O−ring with power steering fluid and install it
to the bushing.
(c) Push in the bushing.
NOTICE:
Make sure to install the bushing facing the correct direc-
tion.
(d) Push in the cylinder end stopper until the wire installation
hole appears.
5. INSTALL WIRE
(a) Insert a new wire end into the hole of the rack housing.
(b) Using SST, turn the cylinder end stopper clockwise until
the wire end disappears.
SST 09631−10021
6. AIR TIGHTNESS TEST
(a) Install SST to the rack housing.
SST 09631−12071
(b) Apply 53.3 kPa (400 mmHg, 15.75 in.Hg) of vacuum for
about 30 seconds.
(c) Check that there is no change in the vacuum.
If there is change in the vacuum, check the installation of the oil
seals.
7. INSTALL CONTROL VALVE ASSEMBLY
(a) Coat the teflon rings with power steering fluid.
(b) To prevent oil seal lip damage, wind vinyl tape on the ser-
rated part of the valve shaft.
(c) Install the valve assembly into the control valve housing.
NOTICE:
Be careful not to damage the teflon rings and oil seal.
8. INSTALL OIL SEAL
(a) Coat a new oil seal lip with power steering fluid.
(b) Using SST, press in the oil seal.
SST 09612−22011
NOTICE:
Make sure to install the oil seal facing the correct direction.
Page 1841 of 2062

Downloaded from www.Manualslib.com manuals search engine BE−6
− BODY ELECTRICALBODY ELECTRICAL SYSTEM
1996 TOYOTA T100 (RM449U)
COMBINATION METER
Meter, Gauge and Illumination:
SymptomSuspect AreaSee page
Tachometer, fuel gauge oil Pressure and water temperature
gauge do not operate
1. GAUGE Fuse (Junction Block No.1)
2. Combination Meter Wiring Circuit
3. Wire Harness
4. Meter Circuit Plate−
BE−36
−
BE−36
Speedometer does not operate1. Vehicle Speed Sensor
2. Speedometer Driven Gear and Drive GearBE−38
−
Tachometer does not operate
1. Combination Meter Wiring Circuit
2. Wire Harness
3. Igniter
4. Meter Circuit PlateBE−36
−
−
−
BE−36
Fuel gauge does not operate or abnormal operation
1. Fuel Receiver Gauge
2. Fuel Sender Gauge
3. Combination Meter Wiring Circuit
4. Wire HarnessBE−38
BE−38
BE−36
−
Engine coolant temperature gauge does not operate
or abnormal operation
1. Engine Coolant Temperature Receiver Gauge
2. Engine Coolant Temperature Sender Gauge
3. Combination Meter Wiring Circuit
4. Wire HarnessBE−38
BE−38
BE−36
−
Oil pressure gauge does not operte or abnormal operation
1. Oil Pressure Receiver Gauge
2. Oil Pressure Sender Gauge
3. Combination Meter Wiring Circuit
4. Wire HarnessBE−38
BE−38
BE−36
−
All illumination lights do not light up
1. TAIL Fuse (Junction Block No.1)
2. Light Control Rheostat
3. Wire Harness−
BE−38
−
Brightness does not change even when rheostat turned1. Bulb
2. Wire Harness−
−
Only one illumination light does not light up1. Bulb
2. Wire Harness−
−
COMBINATION METER
Warning Lights:
SymptomSuspect AreaSee page
Warning light do not light up (Except Discharge)
1. GAUGE Fuse (Junction Block No.1)
2. Combination Meter Wiring Circuit
3. Wire Harness−
BE−36
−
Oil pressure warning light does not light up
1. Bulb
2. Combination Meter Wiring Circuit
3. Oil Pressure Warning Switch
4. Wire Harness−
BE−36
BE−38
−
Washer Fluid Level Warning light does not light up
1. Bulb
2. Combination Meter Wiring Circuit
3. Washer Fluid Level Warning Switch
4. Wire Harness−
BE−36
BE−38
−
Fuel level warning light does not light up
1. Bulb
2. Combination Meter Wiring Circuit
3. Fuel Level Warning Switch
4. Wire Harness−
BE−36
BE−38
−