1996 TOYOTA SUPRA lock

59
Your automatic transmission has a shift
lock system to minimize the possibility of
incorrect operation. This means you can
only shift out of Pº position when thebrake
pedal is depressed (with the ignition
switch in ONº position and the lock re-
lease button depressed).
(a) Normal Driving
1. Start the engine as instructed in How
to start the engineº in Part 3. The trans- mission must be in Pº or Nº.
2. With your foot holding down the brake
pedal, shift the selector lever to Dº.
In Dº position, the automatic transmis-
sion system will select the most suitable
gear for running conditions such as nor-
mal cruising, hill climbing, hard towing,etc.
Always turn the overdrive switch on for
better fuel economy and quieter driving. If
the engine coolant temperature is low, the transmission will not shift into overdrive
gear even with the overdrive switch on.
Never put your foot on the accelera-
tor pedal while shifting. CAUTION
!
3. Release the parking brake and brake
pedal. Depress the accelerator pedal
slowly for smooth starting. (b) Using engine braking
To use engine braking, you can downshift the transmission as follows:
Turn off the overdrive switch. The O/D
OFFº indicator light will come on and the transmission will downshift to the
third gear.
Shift into the 2º position. The trans-
mission will downshift to the second
gear when the vehicle speed drops down to or lower than the followingspeed, and more powerful engine
braking will be obtained.
2JZ-GE engine 115 km/h (72 mph)
2JZ-GTE engine 130 km/h (81 mph)
Shift into the Lº position. The trans- mission will downshift to the first gear
when the vehicle speed drops down to
or lower than the following speed, and
maximum engine braking will be ap- plied.
2JZ-GE engine 48 km/h (29 mph)
2JZ-GTE engine 60 km/h (37 mph) When the cruise control is being used, even if you downshift the transmission by
turning off the overdrive switch, engine
braking will not be applied because the
cruise control is not cancelled. For ways
to decrease the vehicle speed, see
Cruise controlº in this chapter.
Be careful when downshifting on a
slippery surface. Abrupt shifting
could cause the vehicle to spin orskid.
CAUTION
!
(c) Using the 2º and Lº positions
The 2º and Lº positions are used for
strong engine braking as described pre-
viously. With the selector lever in 2º or Lº, you
can start the vehicle in motion as with the
lever in Dº. With the selector lever in 2º, the vehicle
will start in the first gear and automatically
shift to the second gear.
With the selector lever in Lº, the trans-
mission is engaged in the first gear.

60
NOTICE
Be careful not to overrev the en-gine. Watch the tachometer to
keep engine rpm from going into the red zone. The approximatemaximum allowable speed for
each position is given below foryour reference:
2JZ-GE engine
2º 115 km/h (72 mph)Lº 63 km/h (39 mph)
2JZ-GTE engine 2º 130 km/h (81mph)Lº 70 km/h (44mph)
Do not continue hill climbing orhard towing for a long time in the2º or Lº position. This may
cause severe automatic transmis-
sion damage from overheating. To
prevent such damage, Dº posi-
tion should be used in hill climb-ing or hard towing.
(d) Backing up
1. Bring the vehicle to a complete stop.
2. With the brake pedal held down with your foot, shift the selector lever to the Rº
position.
NOTICE
Never shift into reverse while the vehicle is moving.
(e) Parking
1. Bring the vehicle to a complete stop.
2. Pull the parking brake lever up fully to securely apply the parking brake.
3. With the brake pedal pressed down,
shift the selector lever to the Pº position.
While the vehicle is moving, never
attempt to move the selector lever
into Pº position under any circum-
stances. Serious mechanical dam-
age and loss of vehicle control may result. CAUTION
!
(f) Good driving practice
If the transmission is repeatedly upshifted
and downshifted between third gear and
overdrive when climbing a gentle slope,
the overdrive switch should be turned off. Be sure to turn the switch on immediatelyafterward.
Always keep your foot on the brake
pedal w hile stopped with the engine
running. This prevents the vehicle
from creeping. CAUTION
!
NOTICE
Do not hold the vehicle on an upgrade with the accelerator pedal.
It can cause the transmission to overheat. Always use the brakepedal or parking brake.
(g) Driving in manual mode
In the manual mode, the transmission
system stops automatic gear shifting. Use
this m ode when starting your vehicle on a
snowy or slippery road, when driving upsteep inclines, and down with enginebraking.
To set the manual mode, push the
MANUº button. In the manual mode, the
MANUº mode indicator light comes on
and the transmission shifts up or down as follows.
Dº positionÐThe transmission is locked
in third gear.
When your vehicle speed drops down, the
transmission will shift to second gear for
smooth accelerating.
2º positionÐThe transmission is locked
in second gear.
Lº positionÐThe transmission is locked
in first gear.

61
NOTICE
Be careful not to overrev the engine when using 2º or Lº position.
If the automatic transmission fluid tem-
perature becomes too high, the MANUº mode indicator light flashes for several
seconds and goes off. The driving mode then automatically changes from manual mode to the normal driving mode.
To cancel the manual mode, push the
MANUº button once again. The MANUº
mode indicator light will go off and thetransmission system will work in the nor- mal driving mode.
The manual mode automatically cancels
out when the ignition switch is off.
(h) If you cannot shift the selector lever out of Pº position
If you cannot shift the selector lever from the Pº position even though the brake
pedal is depressed, use the shift lock
override button. For instructions, see If you cannot shift automatic transmission selector leverº in Part 4.
The shift pattern is conventional as
shown above.
Press the clutch pedal down fully while
shifting, and then release it slowly. Do not
rest your foot on the pedal while driving, because it will cause clutch trouble. And do not use the clutch to hold the vehicle
when stopped on an uphill gradeÐuse the
parking brake. Recommended shifting speeds
The transmission is fully synchronized
and upshifting or downshifting is easy.
For the best compromise between fuel
economy and vehicle performance, you
should upshift or downshift at the follow-
ing speeds:
gear km/h (mph)
1 to 2 or 2 to 1 24 (15)
2 to 3 or 3 to 2 40 (25)
3 to 4 or 4 to 3 64 (40)
4 to 5 or 5 to 4 72 (45)
Upshifting too soon or downshifting too late
will cause lugging, and possibly pinging.
Regularly revving the engine to maximum
speed in each gear will cause excessive
engine wear and high fuel consumption. Maximum allowable speeds
To get on a highway or to pass slower traf- fic, maximum acceleration may be neces-
sary. Make sure you observe the following
maximum allowable speeds in each gear:
gear km/h (mph) 1 54 (34)
2 94 (59)
3 139 (87)
Manual Transmission

Part 1Car audio system operating tips
65
OPERATION OF INSTRUMENTS AND CONTROLSÐ
Chapter 1-7 Car audio system and Air conditioning system
Car audio system operating tips
AM-FM radio with electronic tuner and cassette tape player
AM-FM radio with electronic
tuner, cassette tape player and Compact Disc player
Automatic air conditioning controls
Dashboard vents
Lower vent
You can listen to the car audio system
when the ignition key is at ONº or
ACCº. However, if the engine is not
running,
the key must be in the ACCº
position.
ILLUMINATION CONTROL LOGIC When the instrument panel lights are on,
the letters on operable buttons of the
mode in current use light up. On some au-
dio-units, the mode selection and eject
buttons also light up.
On some audio-units, when a cassette tape is not in the slot, the letters on the tape mode buttons do not light up, but the
slot lights up for easy access. Once a cas-
sette tape is inserted, the letters on the
tape mode buttons light up, and the slot
stops illuminating. RADIO FM reception tips
Most of us are not aware that a vehicle is
not an ideal place to listen to a radio. Be- cause it moves, reception conditions
change continuously. Buildings, terrain,
signal distance and noise from other ve-
hicles are all working against good recep-
tion. Some FM reception conditions may appear to be problems even though they are normal.
The following characteristics are normal
for a given reception area, and they do not
indicate any problem with the radio itself.
Fading and Drifting: On the average,
the broadcast range of FM stations is limited to about 40 km (25 miles), ex-cept for some high power stations.
If a vehicle is moving away from the
desired station's transmitter, the signal
will tend to fade and/or drift. This phe-
nomenon is more noticeable with FM
than with AM, and is accompanied by distortion.
Fading and drifting can be minimized
to a certain degree by fine tuning, or
you should tune in to a stronger signal.
Static and Fluttering: When the line-
of-sight path between a transmitter
and vehicle is blocked by large build-
ings or the like, static or fluttering may
occur because of the characteristic of
FM. In a similar effect, a fluttering
noise is sometimes heard when driv-
ing along a tree-lined road.
This static and fluttering can be re-
duced by adjusting the tone control for
greater bass response until the distur-
bance has passed.

66
Multipath: Because of the reflection
characteristics of FM, direct and re-
flected signals may reach the antenna
at the same time (a phenomenon
called multipath reception) and cancel
each other out. As a vehicle moves
through these electronic dead spots,
the listener may hear a momentary
flutter or lose reception.
Station swapping: When two FM
stations are close to each other, and
an electronic dead spot, such as is
caused by static or multipath recep-
tion, interrupts the original signal,
sometimes the stronger second si gnal
is picked up automatically until theoriginal one returns. This swapping
can also occur as you drive away from the selected station and approach
another station with a stronger signal.
On models with a power antenna, the an-
tenna automatically extends to its full
height when the radio and ignition are turned on.
To lower the power antenna, turn off the
audio system by pushing PWR VVOLº, or
turn the ignition key to LOCKº.
On some models, the power antenna au-
tomatically retracts when the radio mode
is switched off to turn on the cassette tape
player or compact disc player. Before extending the power antenna,
confirm
that no one is close enough to get
injured by it.
To prevent damage to the antenna,
make sure it is retracted before
running your vehicle through anautomatic car wash.
NOTICE
CASSETTE TAPE PLAYER
Use only undamaged cassette tapes of
good quality. Avoid using tapes with a
total playing time longer than 90 min-utes.
Using damaged tapes will cause trouble with the tape player. Longer tapes are not
recommended because of their thinness.
Before inserting a cassette, make sure
the tape is not slack and that the label
is firmly stuck on the shell.
Wind the tape firmly by turning the hub with a pencil or the like.
Be careful not to touch the exposed tape surface.
When not in use, take the cassette out
of the player, put it back into its case and store it away from dust, magnets
and direct sunlight.
Leaving cassettes on the dashboard in the sun could damage your tapes. Keep the playback head, capstan and pinch roller clean. Remove tape coating residue accumu- lated on the head, capstan and pinch
roll-
er once or twice a month. A cleaning tape is available on the market.
Do not oil any part of the player and
do not insert anything other than
cassette tapes into the slot, or thetape player may be damaged.
NOTICE

100BI-LEVEL buttonÐThis button directs
the air flow to face level and the floor. Ex-
cept in ventilation, the air to the floor is
slightly warmer than that to face level.
FLOOR buttonÐThis button directs the
air flow mostly to the floor.
FLOOR/WINDSHIELD buttonÐThis but- ton directs the air flow to the windshield
and front side windows as well as the floor.
WINDSHIELD buttonÐThis button di-
rects the air flow to the windshield and
front side windows.
Pressing this air flow control button turns
on the air conditioning. This is to clear up
the front view more quickly.
Pressing the air conditioning on-off but-
ton in the off mode turns off the air condi- tioning.
If you push the WINDSHIELD button once
again, it returns to the last air flow button used. Do not use the WINDSHIELD button dur-
ing cooling operation in extremely humid
weather.
The difference between the tem-
perature of the outside air and that of the windshield could cause the outer surface
of the windshield to fog up blocking yourvision. If manual fan speed control is de- siredÐ
The fan speed can be fixed at your desired
speed by turning to the appropriate posi-tion of the fan speed control knob. The
higher
the fan speed is, the more air is de-
livered.
(B) WINDSHIELD DEFOGGING AND DEFROSTING
See (A) CLIMATE CONTROLº for details
on each button or lever function.
To remove interior fog on the wind- shieldÐ
1. Turn the temperature control knob for the desired temperature level.
2. Press in the AUTOº button.
3. Set the air intake control button to the OUTSIDE AIR mode.
4. Press in the WINDSHIELD button of the air flow control buttons.
To remove frost or exterior fog on the windshieldÐ
1. Turn the temperature control knob at the maximum temperature.
2. Set the air intake control button to the OUTSIDE AIR mode.
3. Press in the WINDSHIELD button of the air flow control buttons.
4. Turn the fan speed control knob at the
HIº position. 5. Press the air conditioning on-off but- ton in the OFF mode.
(C) OPERATING TIPS
Be sure the air inlet grilles in front of the
windshield are not blocked by leaves or other obstructions.
If air flow control is not satisfactory,
check the dashboard vents. (See
Dashboard ventsº or Lower ventº.)
To help cool down the interior after
parking in the hot sun, drive for the first
few minutes with the windows open.
After the excess heat has blown away,
close the windows.
When driving on dusty roads, close all
windows. If dust thrown up by the ve-
hicle is still drawn into the vehicle after
closing the windows, it is recom-
mended that the air intake control but-ton be set in the OUTSIDE AIR mode.
If following another vehicle on a dusty
road, or driving in windy and dusty con-
ditions, it is recommended that the air
intake control button be temporarily
set to select the RECIRCULATED AIR
mode, which will close off the outside
passage and prevent outside air and
dust from entering the vehicle interior.

Part 1Cigarette lighter and ashtray
Clock
103
OPERATION OF INSTRUMENTS AND CONTROLSÐ
Chapter 1-8 Other equipment
Clock
Cigarette lighter and ashtray
Glovebox
Luggage cover
Traction control system
Floor mat
The digital clock indicates the time
with the ignition key at the ACCº or
ONº position. To reset the hour, de-
press the
Hº button. To reset the min-
utes, depress the Mº button. To ad-
just the time to a full hour, depress the
:00º button.
For example, if the :00º button is de-
pressed when the time is between
1:01Ð1:29, the time will change to 1:00.
If the time is between 1:30Ð1:59, the time
will change to 2:00. When the instrument panel lights are turned on, the brightness of the time indi- cation will be reduced.
Once the electrical power source has
been disconnected from the clock, the
time is automatically set to 1:00 (oneo'clock).To operate the cigarette lighter, press
it in. When it becomes heated, it auto-
matically pops out ready for use.
If the engine is not running, the key must be in the ACCº position.
Do not hold the cigarette lighter pressed in. When finished with your cigarette, thor-
oughly extinguish it in the ashtray to pre-
vent other cigarette butts from catching
fire. After using the ashtray, close the ash-
tray cover completely.
To remove the ashtray, open the ashtray cover and pull it out.
Use a Toyota genuine cigarette lighter or equivalent for replacement.

104
To open the glovebox door, pull the
lever. To lock the glovebox door, insert
the master key and turn it clockwise.
With the instrument panel lights on, the
glovebox light w ill come on when the door
is open.
To reduce the chance of injury in
case of an accident or a sudden
stop, always keep the glovebox
door closed while driving. CAUTION
!
When you open the back door, the lug-
gage cover tilts up for easy access to the luggage area.
For additional luggage space, unhook the retractable cords and lift the cover out of the retainers.AUTOMATIC MODE
The traction control system automati-
cally controls spinning of the rear
wheels which may occur when accel-
erating on
slippery road surfaces, thus
assisting driver control and driving
power to the rear wheels. When you turn the ignition switch on, the trac-
tion control system always turns on
automatically, and the slip indicator
light and SNOWº indicator light will come on. The indicator lights will go
off after about 3 seconds.
Glovebox Luggage cover Traction control system