1996 TOYOTA RAV4 FRONT BUMPER

BO0ZQ−15
Z17567
BO−4
− BODYFRONT BUMPER
1996 RAV4 (RM447U)
FRONT BUMPER
COMPONENTS

BO481−01
N11455
N11456
− BODYFRONT BUMPER
BO−5
1996 RAV4 (RM447U)
REMOVAL
1. REMOVE FRONT FENDER MOULDING
2. REMOVE FENDER LINER
3. REMOVE FRONT BUMPER COVER
Remove the 4 bolts, 3 clips, 2 screws and the bumper cover.
4. REMOVE HEADLIGHT UNDER COVER
5. REMOVE HEADLIGHT
6. REMOVE UPPER REINFORCEMENT
Torque: 4.9 N·m (50 kgf·cm, 43 in.·lbf)
7. REMOVE BUMPER STAY
Torque: 4.9 N·m (50 kgf·cm, 43 in.·lbf)

BO482−01
BO−6
− BODYFRONT BUMPER
1996 RAV4 (RM447U)
INSTALLATION
Installation is in the reverse order of removal procedure (See page BO−5).

HINT: For symbols, capital letters indicate right side of vehicle,
small letters indicate left side of vehicle (Seen from rear).
K-k
1386
(54.57)552
(21.73)C-K
or
c-k
1494
(58.82)C-k
or
c-K
(Three-Dimensional Distance)
mm (in.)
Hole dia.
6 (0.24) nut
10 (0.39)
10 (0.39)
6 (0.24) nut
10 (0.39) Name
Cooler condenser installation nut
Radiator support extension standard hole
Radiator support standard hole
Front bumper support installation nut
Front apron to cowl side member standard hole Symbol
G, g
H, h
I, i
J
K, k Hole dia.
6 (0.24) nut
11 (0.43)
6 (0.24) nut
13 (0.51)
18 (0.71) Name
Front fender installation nut
Front spring support hole - inner
Front fender installation nut
Cowl top panel center mark
Front side member standard hole
Front side member standard hole Symbol
A, a
B, b
C, c
D, d
E, e
F, f
BODY DIMENSION DRAWINGS
ENGINE COMPARTMENT
BODY DIMENSIONSDIœ3

LOCATION OF PLASTIC BODY PARTS
Quarter Vent Duct (PP)
Rear Door Outside Handle (PC)
Front Door Outside Handle (PC)
Outer Rear View Mirror (AAS)
Instrument Panel Safety Pad (PP)
Cowl TopVentilator Louver (PP)
Radiator Grill (ABS)
Quarter Outside Moulding
(TSOP)
Rear Door Outside Moulding (TSOP) Front Bumper Cover (TSOP)
Front Turn Signal Light (PMMA/PP)
Front Door Outside Moulding (TSOP)
Front Fender Moulding (TSOP)
HINT:
wResin material differs with model.
/ Made up of 2 or more kinds of materials.
PLASTIC BODY PARTSPPœ4

Rear Combination Light (PMMA/PP)
Roof Side Inner Garnish (TSOP)
Air Conditioner Unit (PP)
Heater Blower (PP)
Rear Bumper Side Seal (PE)
Cowl Side Trim Board (PP)
Deck Trim Side Panel (TSOP) Front Door Outside Scuff Plate (PP/PE)
Back Door Outside Handle (PC) Rear Door Outside Scuff Plate (PP/PE)
Rear Bumper Piece (TSOP)
Licence Plate Light (PC)
Reflex Reflector (PMMA/ABS)
HINT:
wResin material differs with model.
/ Made up of 2 or more kinds of materials.
PLASTIC BODY PARTSPPœ6

CO18L−01
S01356
(A)
S01433
− COOLINGELECTRIC COOLING FAN
CO−21
1996 RAV4 (RM447U)
REMOVAL
1. REMOVE NO.1 COOLING FAN (See page CO−16)
2. REMOVE NO.2 COOLING FAN
(a) Remove the RH engine under cover.
(b) w/ A/C:
Remove the cooler condenser (See page AC−47).
(c) Remove the upper radiator supports.
Torque:13 N·m (130kgf·cm, 9 ft·lbf)
HINT:
At the time of installation, plaese refer to the following items. Af-
ter installation, check that the rubber cushion (A) of the support
is not depressed.
(d) Remove the No.2 cooling fan.
(1) Disconnect the cooling fan connector.
(2) Push the radiator toward the front bumper.
(3) Remove the 3 bolts.
(4) Push the No.2 cooling fan toward radiator and pull
it upward.

SA0TK−03
Z19329
Suspension
Support
No.2
CapSpring Upper Seat
Spring
Bumper
Lower
Insulator
Shock Absorber Coil Spring Upper
Insulator
ABS Speed
Sensor Suspension
Support
Dust Seal Shock Absorber
with Coil Spring
Front Drive Shaft
Flexible Hose
Tie Rod End
Cotter Pin
Disc
Cotter Pin
Lock Cap
Lower Ball JointCotter Pin
Brake Caliper
Lower Suspension Arm80 (820, 59)
47 (475, 34)
5 (55, 48 in.·lbf)
158 (1,610, 117)
107 (1,090, 79)
127 (1,300, 94)
49 (500, 36)
216 (2,200, 159)
127 (1,300, 94)
19 (192, 14)
8 (80, 69 in.·lbf)
Dust Deflector
 

 
N·m (kgf·cm, ft·lbf): Specified torque
Non−reusable part
SA−32
− SUSPENSION AND AXLEFRONT SHOCK ABSORBER
1996 RAV4 (RM447U)
FRONT SHOCK ABSORBER
COMPONENTS