Page 716 of 1399
AB0117
R14303H00033
LOCK
Airbag Sensor Assembly
Tc
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−283
1996 LAND CRUISER (RM451U)
If the DTC is displayed without a DTC check procedure, perform the followi\
ng
troubleshooting.
1 Check resistance between terminal Tc of airbag sensor assembly and body
ground.
PREPARATION:
(a) Turn ignition switch to LOCK.
(b) Disconnect negative ( −) terminal cable from the battery,
and wait at least 90 seconds.
(c) Disconnect airbag sensor assembly connector.
CHECK:
Check resistance between terminal Tc of airbag sensor assem-
bly connector and body ground.
OK:
Resistance: 1 MΩ or Higher
NG Repair or replace harness or connector.
OK
Replace airbag sensor assembly.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 717 of 1399
DI5O4−02
Customer Problem Analysis
Check and Clear DTC (Precheck)
Vehicle Brought to Workshop
Problem Symptom Confirmation Symptom Simulation
Symptom
does not occur
DTC Check Normal code
DTC Chart Problem Symptom Table
Circuit Inspection Input Signal Check
Parts Inspection
Identification of Problem Repair
Confirmation Test
End Items inside
are titles of pages in this
manual with the page number indicated in the
bottom portion. See the indicated pages
for detailed explanations.
1
2
3 4
5
6 7
8 9
10 Step 2, 5, 8, 10: Diagnostic steps permitting the use
of the T OYOTA hand−held tester or
TOYOTA break −out− box.
P.
DI−285
P. DI−286
P. DI−286
P. DI−291
P. IN−18
P. DI−295
P. DI−306 − DI−310
OK NG
Symptom
occurs
Malfunction code
DI−284
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
451
Author: Date:
1996 LAND CRUISER (RM451U)
CRUISE CONTROL SYSTEM
HOW TO PROCEED WITH TROUBLESHOOTING
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 718 of 1399
DI5O5−01
CRUISE CONTROL SYSTEM Check SheetInspector ’s name:
Customer ’s Name
Date of VehicleRegistration No.
Registration Year
Frame No.
Odometer Reading
/ / km
Mile
Condition of
Problem Occurrence
Date of Problem
How Often does
Occurrence
Problem Occur?
Vehicle Speed when
Problem Occurred / /
Continuous Intermittent ( Times a day)
km
Mile
Brought in
Auto cancel
occurs Driving condition City driving Freeway Up hill Down hill
After cancel occurred, did the driver activate cruise control again?
Yes No
Cancel does not
occur
With brake ON
Except D position shift At 40 km/h (25 mph) or less
When control SW turns to CANCEL position
Cruise control
malfunction
Slip to acceleration side
Slip to deceleration side
Hunting occurs
O/D cut off does not occur
O/D does not return
Switch
malfunction
SET ACCEL COAST RESUME CANCEL
Remains ON Does not light up Blinking
Symptoms
DTC Check
1st Time2nd Time
Normal Code Malfunction Code (Code )
Normal Code Malfunction Code (Code )
Cruise MAIN
indicator light
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−285
1996 LAND CRUISER (RM451U)
CUSTOMER PROBLEM ANALYSIS CHECK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 719 of 1399
DI5O5−01
CRUISE CONTROL SYSTEM Check SheetInspector ’s name:
Customer ’s Name
Date of VehicleRegistration No.
Registration Year
Frame No.
Odometer Reading
/ / km
Mile
Condition of
Problem Occurrence
Date of Problem
How Often does
Occurrence
Problem Occur?
Vehicle Speed when
Problem Occurred / /
Continuous Intermittent ( Times a day)
km
Mile
Brought in
Auto cancel
occurs Driving condition City driving Freeway Up hill Down hill
After cancel occurred, did the driver activate cruise control again?
Yes No
Cancel does not
occur
With brake ON
Except D position shift At 40 km/h (25 mph) or less
When control SW turns to CANCEL position
Cruise control
malfunction
Slip to acceleration side
Slip to deceleration side
Hunting occurs
O/D cut off does not occur
O/D does not return
Switch
malfunction
SET ACCEL COAST RESUME CANCEL
Remains ON Does not light up Blinking
Symptoms
DTC Check
1st Time2nd Time
Normal Code Malfunction Code (Code )
Normal Code Malfunction Code (Code )
Cruise MAIN
indicator light
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−285
1996 LAND CRUISER (RM451U)
CUSTOMER PROBLEM ANALYSIS CHECK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 720 of 1399
DI5O6-02
N06218CRUISE MAIN Indicator Light
BE4034
Indicator Light1.5 sec. 0.5 sec.
ON
OFF
N06219
TC
E1
DLC1
-
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI-286
1996 LAND CRUISER (RM451U)
PRE-CHECK
1. DIAGNOSIS SYSTEM
(a) Check the indicator.
(1) Turn the ignition switch to ON.
(2) Check that the CRUISE MAIN indicator light comeson when the cruise control main switch is turned on,
and that the indicator light goes off when the main
switch is turned OFF.
HINT:
If the indicator check result is not normal, proceed to trouble-
shooting (See page BE-34) for the combination meter section.
(b) Check the DTC.
HINT:
If a malfunction occurs in the No. 1 vehicle speed sensors or ac-
tuator, etc. during cruise control driving, the ECU actuates
AUTO CANCEL of the cruise control and turns on and off the
CRUISE MAIN indicator light to inform the driver of a malfunc-
tion. At the same time, the malfunction is stopped in memory as
a diagnostic trouble code.
(c) Output of DTC using diagnosis check wire. (1) Turn the ignition switch ON.
(2) Using SST, connect terminals Tc and E
1 of DLC1.
SST 09843-18020
(3) Read the DTC on the CRUISE MAIN indicator light.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 721 of 1399
BE4032
BE4033I00021
Normal Code
0.25 sec.
0.25 sec.
ON
OFF
ON
OFF
4 sec. 1.5 sec.
0.5 sec.
2.5 sec.0.5 sec.1.5 sec.
Malfunction codes 11 and 21
Code 11 Code 21
N09348
TOYOTA hand-held tester
TOYOTA Break-out-box
N18670
Instrument Panel Junction Block ECU- B
Fuse
DI-287
-
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
HINT:
If the DTC is not output, inspect the diagnosis circuit (See page
DI-333 )
As an example, the blinking patterns for codes; normal, 11 and
21 are shown in the illustration.
2. ECU TERMINAL VALUES MEASUREMENT BY USING TOYOTA BREAK-OUT-BOX AND TOYOTA HAND-
HELD TESTER
(a) Hook up the TOYOTA break- out- box and TOYOTA hand-held tester to the vehicle.
(b) Read the ECU input/output values by following the prompts on the tester screen.
(c) Please refer to the TOYOTA hand-held tester has a ºSnapshotº function. This records the measured data and
is effective in the diagnosis of intermittent problems.
3. DTC CLEARANCE
(a) After completing repairs, the diagnostic trouble code re- tained in memory can be cleared by removing the ECU-B
fuse for 10 seconds or more, with the ignition switch off.
(b) Check that the normal code is displayed after connecting the fuse.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 722 of 1399
N14305
N14305
N14305
-
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI-288
1996 LAND CRUISER (RM451U)
4. PROBLEM SYMPTOM CONFIRMATION (ROAD TEST)
(a) Inspect the SET switch.
(1) Push the main switch ON.
(2) Drive at a desired speed (40 km/h (25 mph) or high-
er).
(3) Press the control switch to the SET/COAST.
(4) After releasing the switch, check that the vehicle cruises at the desired speed.
(b) Inspect the ACCEL switch. (1) Push the main switch ON.
(2) Drive at a desired speed (40 km/h (25 mph) or high-
er).
(3) Check that the vehicle speed is increased while the control switch turned to RES/ACC, and that the ve-
hicle cruises at the set speed when the switch is re-
leased.
(4) Momentarily press the control switch upward in the RES/ACC and then immediately release it. Check
that the vehicle speed increases by about 1.5 km/h
(Tap-up function).
(c) Inspect the COAST switch. (1) Push the main switch ON.
(2) Drive at a desired speed (40 km/h (25 mph) or high-er).
(3) Check that the vehicle speed is decreased while the
control switch is turned to SET/COAST, and the ve-
hicle cruise at the set speed when the switch is re-
leased.
(4) Momentarily press the control switch is turned to SET/COAST, and then immediately release it.
Check that the vehicle speed decreases by about
1.5 km/h (Tap-down function).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 723 of 1399
N14305
N14305
DI-289
-
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
(d) Inspect the CANCEL switch. (1) Push the main switch ON.
(2) Drive at a desired speed (40 km/h (25 mph) or high-er).
(3) When operating one of the followings, check that the cruise control system is cancelled and that the
normal driving mode is reset.
Depress the brake pedal
Shift to except D position
Push the main switch OFF
Pull the cruise control switch to CANCEL
(e) Inspect the RESUME switch. (1) Push the main switch ON.
(2) Drive at a desired speed (40 km/h (25 mph) or high-er).
(3) When operating one of the followings, check that
the cruise control system is cancelled and that the
normal driving mode is reset.
Depress the brake pedal
Shift to except D position
Pull the cruise control switch to CANCEL
(4) After the control switch is turned to RES/ACC at the driving speed of more than 40 km/h (25 mph), check
that the vehicle restores the speed prior to the can-
cellation.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
