1996 TOYOTA LAND CRUISER Transmission

CO118−01
CO−16
−
COOLING RADIATOR
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL RADIATOR
(a) Install the 2 radiator brackets with the 4 nuts. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)
(b) Install the radiator with the 2 bolts and 2 nuts. Torque:
Bolt: 18 N·m (185 kgf·cm, 13 ft·lbf)
Nut: 12 N·m (120 kgf·cm, 9 ft·lbf)
2. CONNECT A/T OIL COOLER HOSES
3. CONNECT RADIATOR OUTLET HOSE
4. INSTALL WATER PUMP PULLEY, FAN SHROUD, FAN WITH FLUID COUPLING AND DRIVE BELTS
(a) Place the fan with fluid coupling, water pump pulley and fan shroud in position.
(b) Temporarily install the fan pulley mounting nuts.
(c) Install the fan shroud with the 2 bolts. Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
(d) Connect the oil cooler hose to the clamp on the fan
shroud.
(e) Install the drive belts with the adjusting bolt and pivot bolt.
(f) Stretch the belts tight and tighten the 4 water pump pulley mounting nuts.
(g) Adjust the drive belts (See page CH−2 ).
5. CONNECT RADIATOR RESERVOIR HOSE
6. CONNECT RADIATOR INLET HOSE
7. CONNECT NO.3 WATER BYPASS HOSE
8. INSTALL RADIATOR GRILLE
Install the radiator grille with the 5 screws and clip.
9. INSTALL BATTERY AND BATTERY TRAY
(a) Install the battery tray with the 5 bolts.
(b) Connect the ground strap with the bolt.
(c) Install the battery with the hold−down clamp and nuts.
(d) Connect the battery cables.
10. FILL RADIATOR WITH ENGINE COOLANT
11. START ENGINE AND CHECK FOR LEAKS
12. CHECK AUTOMATIC TRANSMISSION FLUID LEVEL
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22215
−
DIAGNOSTICS ENGINE
DI−5
1996 LAND CRUISER (RM451U)
Terminal No.
Connection / Voltage or ResistanceCondition
2Bus 
Line / Pulse generationDuring transmission
4Chassis Ground / ↔ Body Ground 1 Ω or lessAlways
5Signal Ground / ↔ Body Ground 1 Ω or lessAlways
16Battery Positive / ↔ Body Ground 9 − 14 VAlways
HINT:
If your display shows ”UNABLE TO CONNECT TO VEHICLE”
when you have connected the cable of the OBD II scan tool or
TOYOTA hand−held tester to DLC3, turned the ignition switch
ON and operated the scan tool, there is a problem on the ve-
hicle side or tool side.
If communication is normal when the tool is connected to
another vehicle, inspect DLC3 on the original vehicle.
If communication is still not possible when the tool is con-
nected to another vehicle, the problem is probably in the
tool itself, so consult the Service Department listed in the
tool’s instruction manual.
2. INSPECT DIAGNOSIS (NORMAL MODE)
(a) Check the MIL. (1) The MIL comes on when the ignition switch is turnedON and the engine is not running.
HINT:
If the MIL does not light up, troubleshoot the combination meter
(See page BE−2 ).
(2) When the engine started, the MIL should go off. If the lamp remains on, the diagnosis system has de-
tected a malfunction or abnormality in the system
(b) Check the DTC.
NOTICE:
TOYOTA hand−held tester only: When the diagnosis sys-
tem is switched from normal mode to check mode, it
erases all DTCs and freezed frame data recorded in normal
mode. So before switching modes, always check the DTCs
and freezed frame data, and note them down (1) Prepare the OBD II scan tool (complying with SAE
J 1978) or TOYOTA hand−held tester.
(2) Connect the OBD II scan tool or TOYOTA hand− held tester to DLC3 in the fuse box at the lower left
of the instrument panel.
(3) Turn the ignition switch ON and switch the OBD II
scan tool or TOYOTA hand −held tester switch ON.
(4) Use the OBD II scan tool or TOYOTA hand−held tester to check the DTC and freezed frame data,
note them down. (For operating instructions, see
the OBD II scan tool’s instruction book.)
(5) See page DI−13 to confirm the details of the
DTCs.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

FI3605
ON
OFF Flashing
0.13 Second
DI−6
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
NOTICE:
When simulating symptoms with an OBD II scan tool (ex-
cluding TOYOTA hand −held tester) to check the DTC, use
normal mode. For codes on the DTC chart subject to ”2 trip
detection logic”, turn the ignition switch OFF after the
symptom is simulated the first time. Then repeat the simu-
lation process again. When the problem has been simu-
lated twice, the MIL lights up and the DTCs are recorded in
the ECM.
3. INSPECT DIAGNOSIS (CHECK MODE)
HINT:
TOYOTA hand−held tester only:
Compared to the normal mode, the check mode has an in-
creased sensitivity to detect malfunctions.
Furthermore, the same diagnostic items which are detected in
the normal mode can also be detected in the check mode.
(a) Check the DTC. (1) Initial conditions
Battery positive voltage 11 V or more.
Throttle valve fully closed.
Transmission in ”park” or ”neutral” position.
Air conditioning switched OFF.
(2) Turn ignition switch OFF.
(3) Prepare the TOYOTA hand−held tester.
(4) Connect the TOYOTA hand−held tester to DLC3 in
the fuse box at the lower left of the instrument panel.
(5) Turn the ignition switch ON and push the TOYOTA hand−held tester ON.
(6) Switch the TOYOTA hand −held tester normal mode
to check mode (Check that the MIL flashes.).
(7) Switch the engine (The MIL goes out after the en- gine start.).
(8) Simulate the conditions of the malfunction de- scribed by the customer.
NOTICE:
Leave the ignition switch ON until you have checked the
DTC, etc. (9) After simulating the malfunction conditions, use theTOYOTA hand−held tester diagnosis selector to
check the DTCs and freezed frame data, etc.
HINT:
Take care not to turn the ignition switch OFF. T urning the ignition
switch OFF switches the diagnosis system from check mode to
normal mode, so all DTCs, etc. are erased.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00149
DLC1
E1
TE1 SST
P09137
P23430
−
DIAGNOSTICS ENGINE
DI−9
1996 LAND CRUISER (RM451U)
OK
5 Check idle speed.
PREPARATION:
(a) Warm up engine to normal operating temperature.
(b) Switch off all accessories.
(c) Switch off air conditioning.
(d) Shift transmission into ”N” position.
(e) Connect the OBD II scan tool or TOYOTA hand−held tester to DLC3 on the vehicle.
CHECK:
Use CURRENT DATA to check the idle speed.
OK:
Idle speed: 650 ± 50 rpm
NG Proceed to matrix chart of problem symptomson page DI−19.
OK
6 Check ignition timing.
PREPARATION:
(a) Warm up engine to normal operating temperature.
(b) Shift transmission into ”N” position.
(c) Keep the engine speed at idle.
(d) Using SST, connect terminals TE1 and E1 of DLC1. SST 09843−18020
(e) Connect a timing light probe to a high −tension cord.
CHECK:
Check ignition timing.
OK:
Ignition timing: 3 ° BTDC at idle
NG Proceed to page IG−1 and continue to trouble-
shoot.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−18
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
IGT (E4 −
23) − E1 (E4 − 24)
B − G ↔ BR − BIdlingPulse generation
(See page DI−97)
IGF (E4 − 17) − E1 (E4 − 24)B − Y ↔ BR − B
IG switch ON
Disconnect igniter connector4.5 − 5.5
IdlingPulse generation
(See page DI−97)
G1 (E6 − 11) − G − (E6 − 6)R ↔LIdlingPulse generation
(See page DI−62)
G2 (E6 − 10) − G − (E6 − 6)G ↔LIdlingPulse generation
(See page DI−62)
NE (E6 − 12) − G − (E6 − 6)W ↔LIdlingPulse generation
(See page DI−62)
NE2 (E6 − 5) − G − (E6 − 6)BR ↔ LIdlingPulse generation
(See page DI−62)
W (E7 − 4) − E1 (E4 − 24)Y − R ↔ BR − BIdling9 − 14
IG switch ON0 − 3
EGR (E4 − 22) − E1 (E4 − 24)L − W ↔ BR − BIG switch ON9 − 14
ISC1 (E4 − 7) − E01 (E4 − 13)R − G ↔ BRIG switch ON9 − 14
ISC2 (E4 − 6) − E01 (E4 − 13)R − B ↔ BRIG switch ON9 − 14
ISC3 (E4 − 5) − E01 (E4 − 13)G − Y ↔ BRIG switch ON9 − 14
ISC4 (E4 − 4) − E01 (E4 − 13)L − Y ↔ BRIG switch ON9 − 14
OX1 (E5 − 5) − E1 (E4 − 24)L ↔ BR − BMaintain engine speed at 2,500 rpm for 2 mins. after
warming upPulse generation
OX2 (E5 − 13) − E1 (E4 − 24)W ↔ BR − BMaintain engine speed at 2,500 rpm for 2 mins. after
warming upPulse generation
HT1 (E6 − 1) − E03 (E6 − 16)GR↔BRIdlingBelow 3.0
IG switch ON9 − 14
HT2 (E6 − 7) − E03 (E6 − 16)O↔ BRIdlingBelow 3.0
IG switch ON9 − 14
KNK1 (E5 − 6) − E1 (E4 − 24)W ↔BR − BIdlingPulse generation
(See page DI−62)
KNK2 (E5 − 14) − E1 (E4 − 24)L − W ↔ BR − BIdlingPulse generation
(See page DI−62)
SPD (E7 − 8) − E1 (E4 − 24)L − W ↔ BR − BIG switch ON
Rotate driving wheel slowly.Pulse generation
TE1 (E5 − 7) − E1 (E4 − 24)L↔ BR − BIG switch ON9 − 14
A/C (E7 − 7) − E1 (E4 − 24)B − W↔BR − BIdling, A/C switch ON9 − 14
Idling, A/C switch OFFBelow 2.0
THG (E4 − 19) − E2 (E5 − 9)G − Y↔ BR − BIG switch ON4.5 − 5.5
FC (E4 − 14) − E1 (E4 − 24)R − W↔BR − BIG switch ON9 − 14
Idling0 − 3
FPU (E4 − 21) − E1 (E4 − 24)L − R ↔BR − BIG switch ON9 − 14
Restarting at high engine coolant temp.0 − 3
SDL (E7 − 6) − E1 (E4 − 24)W ↔BR − BDuring transmissionPulse generation
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22487
No.1 Vehicle
Speed SensorCombination
Meter ECM
4−pulse
4−pulse
P22473
Combination Meter
3
C13 L−WL
−W8
E7 SPD ECM
5V
E1
From Cruise Control ECU
−
DIAGNOSTICS ENGINE
DI−87
1996 LAND CRUISER (RM451U)
DTC P0500 Vehicle Speed Sensor Malfunction
CIRCUIT DESCRIPTION
The vehicle speed sensor outputs a 4 − pulse signal for every revolution of the rotor shaft, which is rotated
by the transmission output shaft via the driven gear. After this signal is converted into a more precise rectan-
gular wavefrom by the waveform shaping circuit inside the combination meter, it is then transmitted to the
ECM. The ECM determines the vehicle speed based on the frequency of thes\
e pulse signals.
DTC No.DTC Detecting ConditionTrouble Area
P0500
No vehicle speed sensor signal to ECM under conditions (a)
and (b):
(2 trip detection logic)
(a) Park/neutral position switch is OFF.
(b) Vehicle is being driven. Open or short in No.1 vehicle speed sensor circuit
 No.1 vehicle speed sensor
 Combination meter
 ECM
WIRING DIAGRAM
DI5PN−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5K4−03
Vehicle Brought to Workshop
Customer Problem Analysis
Check DTC and Freezes Frame Data (Pre−check)
Record or Print DTC and Freezed Frame Data
DI−131
Clear DTC and Freezed Frame Data DI−131
Visual Inspection
Setting the Check Mode Diagnosis
DI−131
1
Items insideare titles of pages in this manual, with the
page number indicated in the bottom portion. See the indicated
pages for detailed explanations.
Connect an OBD II scan tool or TOYOTA hand−held tester to DLC3.
If your display shows ”UNABLE TO CONNECT TO VEHICLE” when you have connected the
scan tool/TOYOTA hand− held tester, inspect DLC3
DI−131
2
3
4
5
6
symptom does not occur
Problem Symptom Confirmation8
7Symptom Simulation
symptom occurs
DTC Check
DI−131 OK Code
11Preliminary Check
DTC ChartMechanical System Tests
Manual Shifting Test
OK
OK
Chapter 1
(Electronic) Chapter 2
(On−Vehicle)OKChapter 3
(Off
−Vehicle)OK
Matrix Chart of Problem Symptoms
− DI−147
Circuit
InspectionStop Light Signal
 O/D Cancel Signal Check
NG
Parts Inspection
NG
NG NG
Identification of ProblemRepairConfirmation TestEnd
NG
NG
12
NG13
14
15 16
17
9
10
DI−153 − DI−185
18
DI−130
DI−143
DI−131
DI−131
DI−131
DI−147 DI−147
DI−147
P.IN−18
Step 2, 3, 4, 6, 9, 15, 18:
Diagnostic steps permitting the use of the TOYOTA
hand−held tester or TOYOTA brake− out−box.
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−129
296
Author: Date:
1996 LAND CRUISER (RM451U)
AUTOMATIC TRANSMISSION
HOW TO PROCEED WITH TROUBLESHOOTING
Troubleshoot in accordance with the procedure on the following page.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5K6−01
Transmission Control
System Check SheetInspector ’s
Name
:
Customer ’s Name
Registration No.
Registration Year
Frame No.
Date Vehicle
Brought In Odometer Reading
km
mile
/ /
/ /
Date Problem
Occurred
How Often Does
Problem Occur? / /
 Continuous  Intermittent ( times a day)
Symptoms
 Vehicle does not move (  Any position  Particular position )
 No up−shift (  1st → 2nd  2nd → 3rd  3rd → O/D )
 No down−shift (  O/D → 3rd  3rd → 2nd  2nd → 1st )
 Lock−up malfunction
 Shift point too high or too low
 Harsh engagement (  N → D  Lock −up  Any drive position )
 Slip or shudder
 No kick− down
 Others
Check Item Malfunction
Indicator Lamp
DTC Check1st Time
2nd Time
Normal code  Malfunction code (Code )

Normal 
Remains ON
 Normal code  Malfunction code (Code )
DI−130
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
CUSTOMER PROBLEM ANALYSIS CHECK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010