1996 TOYOTA LAND CRUISER differential

PP2YE−01
PP−50
−
PREPARATION SUSPENSION AND AXLE
1996 LAND CRUISER (RM451U)
LUBRICANT
ItemCapacityClassification
Differential oil
Front w/o Dfferential lock w/ Dfferential lock
Rear
2.80 liters (2.9 US qts, 2.5 lmp. qts)
2.65 liters (2.8 US qts, 2.3 lmp. qts)
3.25 liters (3.4 US qts, 2.9 lmp. qts)
Hypoid gear oil API GL− 5
Above − 18°C (0° F) SAE 90
Below − 18°C (0° F) SAE 80W− 90 or 80W
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP2YF−02
−
PREPARATION SUSPENSION AND AXLE
PP−51
1996 LAND CRUISER (RM451U)
SSM (Special Service Materials)
08826−00090Seal Packing 1281,
THREE BOND 1281 or equivalent
(FIPG)Front differential
Rear differential
Differential locking system
08833−00080Adhesive 1344
THREE BOND 1344
LOCTITE 242 or equivalentFront differential
Rear differential
Differential locking system
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z04247
ColorDrit Mark
Bearing Cup
Drit Mark
Yoke
Q07142
Type A Type B X
610.0 mm (24.016 in.)
Y
545.0 mm (21.457 in.)
X
Y Differential
Side
Z00755
PR0081
Q07338
−
PROPELLER SHAFT SPIDER BEARING
PR−7
855
Author: Date:
1996 LAND CRUISER (RM451U)
5. SELECT SPIDER BEARING
Select the bearing according to whether or not there is a drill
mark on the yoke section.
YokeBearing (T ype A)Bearing (Type B)
w/ drill markw/ color mark (White)w/ color mark (Red)
No drill markNo color markNo color mark
HINT:
At time of the reassemble, there are 2 types of rear propeller
shafts, type A and type B. Referring to the illustration, measure
the distance between the welding points X and Y to identify
which of the 2 types is used for the vehicle.
6. INSTALL SPIDER BEARING
(a) Apply MP grease to a new spider and bearings.
NOTICE:
Be careful not to apply too much grease.
(b) Align the matchmarks on the yoke and flange.
(c) Fit the spider into the yoke.
(d) Using SST, install the bearings on the spider. SST 09332−25010
(e) Using SST, adjust both bearings so that the snap ring grooves are at maximum and equal widths.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1U7−01
−
SUSPENSION AND AXLE TROUBLESHOOTING
SA−1
858
Author: Date:
1996 LAND CRUISER (RM451U)
TROUBLESHOOTING
PROBLEM SYMPTOMS TABLE
Use the table below to help you find the cause of the problem. The numbers \
indicate the priority of the likely
cause of the problem. Check each part in order. If necessary, replace these parts.
(w/ Differential locking system):
Check that center differential lock mode is set.
When switching differential Free↔Lock, the indicator lamp will blink if the gears of the differen-
tial lock sleeve are not meshed. If this occurs, when the tires are rotated \
to apply differential
power to the differential, the differential locks and the indicator lamp\
light up.
SymptomSuspect AreaSee page
Wander/ pulls
1. Tires: worn or improperly inflated
2. Wheel alignmemt: incorrect
3. Steering linkage: loosen or worn
4. Hub bearings: loosen or worn
5. Steering gear: out of adjustment or brokenSA−3
SA−4
SR−47 SA−8
SR−41
Bottoming
1. Vehicle: overloaded
2. Spring weak
3. Shock absorber: worn out−
SA−49
SA−49
Sways/ pitches
1. Tires: worn or improperly inflated
2. Stabilizer bar: bent or broken
3. Shock absorber: worn outSA−3
SA−60
SA−49
Front wheel shimmy
1. Tires: worn or improperly inflated
2. Wheels: out of balance
3. Shock absorber: worn out
4. Wheel alignmemt: incorrect
5. Hub bearings: loosen or worn
6. Steering linkage: loosen or worn
7. Steering gear: out of adjustment or brokenSA−3
SA−3
SA−49 SA−3
SA−7
SR−45
SR−38
Abnormal tire wear
1. Tires: worn or improperly inflated
2. Wheel alignmemt: incorrect
3. Suspension parts: worn out
4. Shock absorber: worn outSA−3
SA−3 −
SA−49
Noise in front dif ferential
1. Oil level: low or wrong grade
2. Excessive backlash between pinion and ring gear
3. Ring, pinion ro side gears: worn or chipped
4. Pinion shaft bearing: worn
5. Side bearing: worn
6. Differential bearing: loosen or wornSA−21
SA−29
SA−29
SA−29
SA−29
SA−29
Oil leak from front dif ferential
1. Oil level: too high or wrong grade
2. Drive pinion oil seal: worn or damaged
3. Side gear oil seal: worn or damaged
4. Companion flange: loosen or damaged
5. Side gear shaft: damagedSA−21
SA−29
SA−29
SA−29
SA−29
Noise in rear axle
1. Oil level: low or wrong grade
2. Excessive backlash between pinion and ring gear
3. Ring, pinion ro side gears: worn or chipped
4. Pinion shaft bearing: worn
5. Axle shaft bearing: worn
6. Differential bearing: loosen or wornSA−73
SA−87
SA−87
SA−87
SA−87
SA−87
Oil leak from rear axle1. Oil seal: worn or damaged
2. Rear axle housing: crackedSA−73
−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA−2
−
SUSPENSION AND AXLE TROUBLESHOOTING
859
Author: Date:
1996 LAND CRUISER (RM451U)
Oil leak from rear dif
ferential
1. Oil level: too high or wrong grade
2. Oil seal: worn or damaged
3. Companion flange: loosen or damagedSA−73
SA−73
SA−87
Indicator lights do not light up
1. Fusible link: blown
2. GAUGE fuse: blown
3. Bulb: burned out
4. Wiring or ground: faultyBE−9
BE−9
BE−32 −
Indicator lights do not light up
(Diff. lock control switch RR or FR RR position)
1. DIFF fuse: blown
2. Diff. lock control switch: faulty
3. Diff. lock ECU: faulty
4. Wiring or ground: faultyBE−9
SA−101
SA−101 −
Differential lock does not operate
1. Diff. lock position switch: faulty
2. Diff. lock actuator: faulty
3. Diff. lock ECU: faulty
4. Differential carrier (Diff. lock): faulty
5. Wiring or ground: faultySA−101
SA−101
SA−101
SA−101−
After differential lock, lock not release
When vehicle speed is higher than approx. 8 km/h (5mph)1. Speed sensor: faulty
2. Diff. lock ECU: faulty
3. Wiring or ground: faultyBE−32
SA−101 −
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1UJ−01
SA−20
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL REAR OIL SEAL
877
Author: Date:
1996 LAND CRUISER (RM451U)
FRONT DIFFERENTIAL REAR OIL SEAL
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1UK−01
Z15176
SST
R13186
SST
SA1973
SST
SA1969
SST
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL REAR OIL SEAL
SA−21
1996 LAND CRUISER (RM451U)
REPLACEMENT
1. DRAIN DIFFERENTIAL OIL
2. REMOVE FRONT PROPELLER SHAFT
(See page PR−3 )
3. REMOVE COMPANION FLANGE
(a) Using a chisel and hammer, loosen the staked part of the
nut.
(b) Using SST to hold the flange, remove the nut and plate washer.
SST 09330−00021
(c) Using SST, remove the companion flange. SST 09950−30010 (09951 −03010, 09953−03010,
09954 −03010, 09955 −03030, 09956−03020)
4. REMOVE OIL SEAL AND OIL SLINGER
(a) Using SST, remove the oil seal. SST 09308−10010
(b) Remove the oil slinger.
5. REMOVE REAR BEARING
Using SST, remove the rear bearing from the drive pinion. SST 09556−22010
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA2430
SST
SA2271
R13155
SSTSST
Oil Storage Ring
Rear Bearing
SA2411
SST
1.0 mm (10.039 in.)
R13139
SST
SA−22
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL REAR OIL SEAL
1996 LAND CRUISER (RM451U)
6. REMOVE REAR BEARING OUTER RACE
Using SST, remove the bearing outer race.
SST 09308−00010
NOTICE:
Do not scratch the taper surface of the outer race.
7. REMOVE OIL STORAGE RING
Using a screwdriver, bend the oil storage ring and drive it out.
8. REMOVE BEARING SPACER
9. INSTALL BEARING SPACER
10. INSTALL OIL STORAGE RING
Using SST, install a new oil storage ring. SST 09316−60011 (09316 −00011, 09316−00021)
11. INSTALL REAR BEARING
(a) Using SST, install the bearing outer race.
SST 09316−60011 (09316 −00011, 09316−00021)
(b) Install the rear bearing.
12. INSTALL OIL SLINGER AND OIL SEAL
(a) Install the oil slinger.
(b) Using SST, install a new oil seal, as shown. SST 09214−76011
Oil seal drive in depth: 1.0 mm (0.039 in.)
(c) Coat the lip of the oil seal with MP grease.
13. INSTALL COMPANION FLANGE
(a) Using SST, install the companion flange on the drive pin- ion.
SST 09950−30010 (09951 −03010, 09953−03010,
09954 −03010, 09955 −03030, 09956−03020)
(b) Place the plate washer on the companion flange.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010