1996 TOYOTA LAND CRUISER check engine light

P22215
−
DIAGNOSTICS ENGINE
DI−5
1996 LAND CRUISER (RM451U)
Terminal No.
Connection / Voltage or ResistanceCondition
2Bus 
Line / Pulse generationDuring transmission
4Chassis Ground / ↔ Body Ground 1 Ω or lessAlways
5Signal Ground / ↔ Body Ground 1 Ω or lessAlways
16Battery Positive / ↔ Body Ground 9 − 14 VAlways
HINT:
If your display shows ”UNABLE TO CONNECT TO VEHICLE”
when you have connected the cable of the OBD II scan tool or
TOYOTA hand−held tester to DLC3, turned the ignition switch
ON and operated the scan tool, there is a problem on the ve-
hicle side or tool side.
If communication is normal when the tool is connected to
another vehicle, inspect DLC3 on the original vehicle.
If communication is still not possible when the tool is con-
nected to another vehicle, the problem is probably in the
tool itself, so consult the Service Department listed in the
tool’s instruction manual.
2. INSPECT DIAGNOSIS (NORMAL MODE)
(a) Check the MIL. (1) The MIL comes on when the ignition switch is turnedON and the engine is not running.
HINT:
If the MIL does not light up, troubleshoot the combination meter
(See page BE−2 ).
(2) When the engine started, the MIL should go off. If the lamp remains on, the diagnosis system has de-
tected a malfunction or abnormality in the system
(b) Check the DTC.
NOTICE:
TOYOTA hand−held tester only: When the diagnosis sys-
tem is switched from normal mode to check mode, it
erases all DTCs and freezed frame data recorded in normal
mode. So before switching modes, always check the DTCs
and freezed frame data, and note them down (1) Prepare the OBD II scan tool (complying with SAE
J 1978) or TOYOTA hand−held tester.
(2) Connect the OBD II scan tool or TOYOTA hand− held tester to DLC3 in the fuse box at the lower left
of the instrument panel.
(3) Turn the ignition switch ON and switch the OBD II
scan tool or TOYOTA hand −held tester switch ON.
(4) Use the OBD II scan tool or TOYOTA hand−held tester to check the DTC and freezed frame data,
note them down. (For operating instructions, see
the OBD II scan tool’s instruction book.)
(5) See page DI−13 to confirm the details of the
DTCs.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

FI3605
ON
OFF Flashing
0.13 Second
DI−6
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
NOTICE:
When simulating symptoms with an OBD II scan tool (ex-
cluding TOYOTA hand −held tester) to check the DTC, use
normal mode. For codes on the DTC chart subject to ”2 trip
detection logic”, turn the ignition switch OFF after the
symptom is simulated the first time. Then repeat the simu-
lation process again. When the problem has been simu-
lated twice, the MIL lights up and the DTCs are recorded in
the ECM.
3. INSPECT DIAGNOSIS (CHECK MODE)
HINT:
TOYOTA hand−held tester only:
Compared to the normal mode, the check mode has an in-
creased sensitivity to detect malfunctions.
Furthermore, the same diagnostic items which are detected in
the normal mode can also be detected in the check mode.
(a) Check the DTC. (1) Initial conditions
Battery positive voltage 11 V or more.
Throttle valve fully closed.
Transmission in ”park” or ”neutral” position.
Air conditioning switched OFF.
(2) Turn ignition switch OFF.
(3) Prepare the TOYOTA hand−held tester.
(4) Connect the TOYOTA hand−held tester to DLC3 in
the fuse box at the lower left of the instrument panel.
(5) Turn the ignition switch ON and push the TOYOTA hand−held tester ON.
(6) Switch the TOYOTA hand −held tester normal mode
to check mode (Check that the MIL flashes.).
(7) Switch the engine (The MIL goes out after the en- gine start.).
(8) Simulate the conditions of the malfunction de- scribed by the customer.
NOTICE:
Leave the ignition switch ON until you have checked the
DTC, etc. (9) After simulating the malfunction conditions, use theTOYOTA hand−held tester diagnosis selector to
check the DTCs and freezed frame data, etc.
HINT:
Take care not to turn the ignition switch OFF. T urning the ignition
switch OFF switches the diagnosis system from check mode to
normal mode, so all DTCs, etc. are erased.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00149
DLC1
E1
TE1 SST
P09137
P23430
−
DIAGNOSTICS ENGINE
DI−9
1996 LAND CRUISER (RM451U)
OK
5 Check idle speed.
PREPARATION:
(a) Warm up engine to normal operating temperature.
(b) Switch off all accessories.
(c) Switch off air conditioning.
(d) Shift transmission into ”N” position.
(e) Connect the OBD II scan tool or TOYOTA hand−held tester to DLC3 on the vehicle.
CHECK:
Use CURRENT DATA to check the idle speed.
OK:
Idle speed: 650 ± 50 rpm
NG Proceed to matrix chart of problem symptomson page DI−19.
OK
6 Check ignition timing.
PREPARATION:
(a) Warm up engine to normal operating temperature.
(b) Shift transmission into ”N” position.
(c) Keep the engine speed at idle.
(d) Using SST, connect terminals TE1 and E1 of DLC1. SST 09843−18020
(e) Connect a timing light probe to a high −tension cord.
CHECK:
Check ignition timing.
OK:
Ignition timing: 3 ° BTDC at idle
NG Proceed to page IG−1 and continue to trouble-
shoot.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5OV−03
−
DIAGNOSTICS ENGINE
DI−13
1996 LAND CRUISER (RM451U)
DIAGNOSTIC TROUBLE CODE CHART
HINT:
Parameters listed in the chart may not be exactly the same as your reading due to \
the type of instrument
or other factors.
If a malfunction code is displayed during the DTC check in check mode, che\
ck the circuit for that code listed
in the table below. For details of each code, turn to the page referred to under the ’’See page ’’ for the respe-
cire ’’DTC No.’’ in the DTC chart.
DTC No.
(See Page)Detection ItemTrouble AreaMILMemory
P0100
( DI−20 )Mass Air Flow Circuit
MalfunctionOpen or short in mass air flow meter circuit
 Mass air flow meter
 ECM
 *1
P0101
( DI−25 )Mass Air Flow Circuit
Range/Performance
Problem
Mass air flow meter *1
P0110
( DI−26 )Intake Air Temp. Circuit
MalfunctionOpen or short in intake air temp. sensor circuit
 Intake air temp. sensor
 ECM
 *1
P0115
( DI−30 )Engine Coolant Temp. Circuit
MalfunctionOpen or short in engine coolant temp. sensor circuit
 Engine coolant temp. sensor
 ECM
 *1
P0116
( DI−34 )Engine Coolant Temp. Circuit
Range/Performance ProblemEngine coolant temp. sensor
 Cooling system *1
P0120
( DI−35 )Throttle/Pedal Position
Sensor/Switch ”A” Circuit
MalfunctionOpen or short in throttle position sensor circuit
 Throttle position sensor
 ECM
 *1
P0121
( DI−39 )Throttle/Pedal Position
Sensor/Switch ”A” Circuit
Range/Performance Problem
Throttle position sensor *1
P0125
( DI−40 )Insufficient Coolant Temp. for
Closed Loop Fuel Control Open or short in heated oxygen sensor circuit
 Heated oxygen sensor *1
P0130
( DI−43 )Heated Oxygen Sensor Circuit
Malfunction (Bank 1 Sensor 1)Heated oxygen sensor
 Fuel trim malfunction *1
P0133
( DI−46 ) Heated Oxygen Sensor Circuit
Slow Response
(Bank 1 Sensor 1)
Heated oxygen sensor *1
P0135
( DI−47 ) Heated Oxygen Sensor Heater
Circuit Malfunction
(Bank 1 Sensor 1)Open or short in heater circuit of heated oxygen sensor
 Heated oxygen sensor heater
 ECM
 *1
P0136
( DI−49 )Heated Oxygen Sensor Circuit
Malfunction
(Bank 1 Sensor 2)
Heated oxygen sensor *1
P0141
( DI−47 ) Heated Oxygen Sensor Heater
Circuit Malfunction
(Bank 1 Sensor 2)
Same as DTC No. P0135 *1
*1: MIL lights up
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

FI7130
Vehicle Speed50 − 65 km/h
(31 − 40 mph)
Idling
IG SW OFF 1 − 3 min.1 min. Time
(1)(2)(3) (4)
(5)
−
DIAGNOSTICS ENGINE
DI−43
1996 LAND CRUISER (RM451U)
DTC P0130 Heated Oxygen Sensor Circuit Malfunction
(Bank 1 Sensor 1)
CIRCUIT DESCRIPTION
Refer to DTC P0125 (Insufficient Coolant Temp. for Closed Loop Fuel Control) on page DI−40.
DTC No.DTC Detecting ConditionTrouble Area
P0130
Voltage output of heated oxygen sensor (bank 1 sensor 1)
remains at 0.4 V or more, or 0.55 V or less, during idling after
the engine is warmed up (2 trip detection logic)Heated oxygen sensor (bank 1 sensor 1)
 Fuel trim malfunction
HINT:
Sensor 1 refers to the sensor closer to the engine body.
The heated oxygen sensor’s output voltage and the shortterm fuel trim value can be read using t\
he OBD
II scan tool or TOYOTA handheld tester.
WIRING DIAGRAM
Refer to DTC P0125 (Insufficient Coolant Temp. for Closed Loop Fuel Control) on page DI−35 for WIRING
DIAGRAM.
CONFIRMATION DRIVING PATTERN
(1) Connect the TOYOTA hand−held tester to the DLC3.
(2) Switch the TOYOTA hand−held tester from normal mode to check mode (See page DI−3).
(3) Start the engine and warm it up withe all accessory switches OFF.
(4) Drive the vehicle at 50 − 65 km/h (31 − 40 mph) for 1 − 3 min. to warm up the heated oxygen sensor.
(5) Let the engine idle for 1 min.
HINT:
If a malfunction exists, the MIL will light up during step (5).
NOTICE:
If the conditions in this test are not strictly followed, detection of the\
malfunction will not be possible.
If you do not have a TOYOTA hand −held tester, turn the ignition switch OFF after performing steps
(3) to (5), then perform steps (3) to (5) again.
DI5PA−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS ENGINE
DI−51
1996 LAND CRUISER (RM451U)
DTC P0171 System too Lean (Fuel Trim)
DTC P0172 System too Rich (Fuel Trim)
CIRCUIT DESCRIPTION
”Fuel trim” refers to the feedback compensation value compared against the basic injection time. Fuel trim
includes short−term fuel trim and long −term fuel trim.
”Short−term fuel trim” is the short−term fuel compensation used to maintain the air −fuel ratio at its ideal
theoretical value. The signal from the heated oxygen sensor indicates whether the a\
ir −fuel ratio is RICH or
LEAN compared to the ideal theoretical value, triggering a reduction in fuel \
volume if the air −fuel ratio is rich,
and an increase in fuel volume if it is lean.
”Long −term fuel trim” is overall fuel compensation carried out long −term to compensate for continual devi-
ation of the short−term fuel trim form the central value due to individual engine differences, wear over time
and changes in the usage environment.
If both the short−term fuel trim and long−term fuel trim are LEAN or RICH beyond a certain value, it is de-
tected as a malfunction and the MIL lights up.
DTC No.DTC Detecting ConditionTrouble Area
P0171
When the air fuel ratio feedback is stable after engine warming
up, the fuel trim is considerably in error on the RICH side.
(2 trip detection logic)
 Air intake (hose loose)
 Fuel line pressure
 Injector blockage, leak
 Heated oxygen sensor (bank 1 sensor 1) malfunction
 Mass air flow meter
 Engine coolant temp. sensor
P0172
When the air fuel ratio feedback is stable after engine warming
up, the fuel trim is considerably in error on the LEAN side.
(2 trip detection logic)
Fuel line pressure
 Injector blockage, leak
 Heated oxygen sensor (bank 1 sensor 1) malfunction
 Mass air flow meter
 Engine coolant temp. sensor
HINT:
When the DTC P0171 is recorded, the actual air− fuel ratio is on the LEAN side. When DTC P0172 is
recorded, the actual air−fuel ratio is on the RICH side.
If the total of the short −term fuel trim value and long −term fuel trim value is within + 30 − − 35 %, the
system is functioning normally.
If the vehicle runs out of fuel, the air −fuel ratio is LEAN and DTC P0171 is recorded. The MIL then come
on.
INSPECTION PROCEDURE
1 Check air induction system (See page SF−1 ).
NG Repair or replace
OK
DI5PE−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P20769
(43 − 56 mph)
Vehicle Speed
70 − 90 km/h
Idling
IG SW OFF (1)(2) (3)
(4) (6)
(5)
Warm up 3 − 5 min. 2 min.
3 − 5 min.2 min.(7)
Time
DI−70
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
SYSTEM CHECK DRIVING PATTERN
(1) Connect the OBD II scan tool or TOYOTA hand −held tester to the DLC3.
(2) Start and warm up the engine with all accessories switched OFF.
(3) Run the vehicle at 70 − 90 km/h (43 − 56 mph) for 3 min. or more.
(4) Idle the engine for about 2 min.
(5) Stop at safe place and turn the ignition switch OFF.
(6) Start the engine and do steps (3) and (4) again.
(7) Check the ”READINESS TESTS” mode on the OBD II scan tool or\
TOYOTA hand−held tester.
If ”COMPL” is displayed and the MIL does not light up, the system \
is normal.
If ”INCMPL” is displayed and the MIL does not light up, run the ve\
hicle again and check it.
HINT:
”INCMPL” is displayed when either condition (a) or (b) exists.\
(a) The system check is incomplete.
(b) There is a malfunction in the system.
If there is a malfunction in the system, the MIL will light up after ste\
ps (2) to (6) above are done.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08225
Q08634
TOYOTA Hand−held Tester
DLC3
DI−132
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
The diagnosis system operates in normal mode
during normal vehicle use, and also has a check
mode for technicians to simulate malfunction symp-
toms and perform troubleshooting. Most DTCs use
2 trip detection logic(*) to prevent erroneous detec-
tion. By switching the ECM to check mode when
troubleshooting, the technician can cause the MIL
to light up for a malfunction that is only detected
once or momentarily (TOYOTA hand−held tester)
(See step 3).
*2 trip detection logic:
When a logic malfunction is first detected, the mal-
function is temporarily stored in the ECM memory.
If the same malfunction is detected again during the 2nd test
drive, this 2nd detection causes the MIL to light up.
2. Normal Mode: INSPECT DIAGNOSIS
(a) Check the MIL. (1) The MIL lights up when the ignition switch is turnedON and the engine is not running.
HINT:
If the MIL does not light up, troubleshoot the combination meter
(See page BE−2 ).
(2) When the engine is started, the MIL should go off.
If the lamp remains on, the diagnosis system has
detected a malfunction or abnormality in the sys-
tem.
(b) Check the DTC.
NOTICE:
TOYOTA hand−held tester only:
When the diagnostic system is switched from the normal
mode to the check mode, it erases all DTCs and freeze
frame data recorded in the normal mode. So before switch-
ing modes, always check the DTCs and freeze frame data,
and note them down. (1) Prepare the OBD II scan tool (complying with SAEJ1978) or TOYOTA hand−held tester.
(2) Connect the OBD II scan tool or TOYOTA hand−
held tester to the DLC3 in the fuse box at the lower
left of the instrument panel.
(3) Turn the ignition switch ON and turn the OBD II scan
tool or TOYOTA hand−held tester switch ON.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010